Jump to content

2020 2500HD L5P no communications with modules

rdomeck
 Share

Recommended Posts

rdomeck New Member

rdomeck

Posted
Posted

Hey guys.  I have no communication with multiple modules on my truck.  I have been searching and searching, nut can't find related threads.  

 

 

I have been fighting an issue for about three days.  The truck has been rebuilt.  I put a frame under it and a lot of other repairs.  I had it running and driving, but something was running my batteries down completely overnight.  I could not get my batteries to hold a charge any more and this is when the issue started while I was starting to troubleshoot.  I am getting a U0100 code.  

 

I have communication with my BCM.  I do not have it with the ECM, TCM, TBCM (Trailer Brake Control Module).

 

I need help!

carkhz316 Enthusiast

carkhz316

Posted
Posted (edited)

Check the ground in the engine bay that is attached to the fender support just forward of the coolant bottle on the left side. Its G114. This is the ground for the ECM, TCM, and some others. If this is the culprit, I'd assume you'd have loss of comms with more modules relating to the diesel-specific items including the reductant module and various exhaust sensors.

 

Barring that, list all the modules that have no communication, or the modules that are REPORTING loss of communications and with what modules that THEY can't communicate with.

 

The battery drain can be addressed later, as its likely a symptom of the above issues.

Edited by carkhz316
rdomeck New Member

rdomeck

Posted
  • Author
Posted

 

I have viewed and inspected all the ground locations listed with AllData. I had even sanded each location and put a good amount of dielectric grease on each during reassembly.

 

I would agree that it sound like a ground issue.  But all of them are checking out good!

 

I have the following things not working.

-Fuel gauge

-Outside temp is reading -40

-Brake pad sensor malfunction

-Service Parking brake, but that is working

-Traction control light on

-TPMS light on

 

The following codes descriptions.

 

Invalid data received from body control module

Lost comm with TCM

Lost comm with ECM

invalid data from front and rear brake wear circuit

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   
    • devonthegreat
      anyone interested in a 2002 Chevy Silverado 4x4 parts truck NYC

      By devonthegreat · Posted

      **SOLD** Please end or delete post. thank you
    • PBNB
      Tire pressure for 37s

      By PBNB · Posted

      Do you think this width might affect the chalk test with a higher pressure closer to 65psi? I think lowering the pressure makes sense to get the tread to lay flatter

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...