Jump to content

Recommended Posts

Posted (edited)

Long story short. 2016 GMC Sierra SLT 4X4 Z71 crew cab. When driving at night everything is normal. Lights work fine and instrument cluster is normal. After 5 to 10 minutes the headlights turn off, fog lights stay on and the instrument cluster goes to full brightness. The dimmer switch will control the HVAC and other interior lights normally, the cluster stays full bright and tbh I think it's much brighter than normal. The headlights will turn on with the manual headlight switch but the cluster stays full bright. After 5-10 minutes the cluster will go back to normal and the auto headlights work normally. This cycles randomly and only happens at night.

 

I pulled the test procedure and tested out the light sensor on the dash. It tested good, but I replaced it anyway 3 times with dealer parts. I replaced the BCM, I replaced the instrument cluster. The only thing that is next is the hvac module that the light sensor runs through. I can program the modules and they are relatively cheap on rock auto so throwing parts isn't that much of an issue for me, but I am getting tired of dealing with this. Has anyone ran across this and found a fix?

Edited by spayne460
Posted (edited)

Instead of throwing parts at it, have you gone through "ALL" the grounds? There are several that are connected to body as well as the infamous G214 that you can find under the dash speaker on left side of dash. Especially on the 2014-15, it is a known issue and isn't always a clean ground and the insulation may need to be cleared away from the stud.  Bad grounds cause all kinds of intermittent problems. Also an old weak battery will also cause problems. Make sure to also check the main negative cable coming off the battery.

Edited by mikeyk101
  • Like 2
Posted

I would start with what mikeyk101 said...

Posted
23 hours ago, mikeyk101 said:

Instead of throwing parts at it, have you gone through "ALL" the grounds? There are several that are connected to body as well as the infamous G214 that you can find under the dash speaker on left side of dash. Especially on the 2014-15, it is a known issue and isn't always a clean ground and the insulation may need to be cleared away from the stud.  Bad grounds cause all kinds of intermittent problems. Also an old weak battery will also cause problems. Make sure to also check the main negative cable coming off the battery.

I have checked these grounds. The problem is not intermittent enough to be grounds. It's pretty predictable. But yes body grounds to the frame and the one under the speaker. I could see if it was you hit a bump and it would start/stop but this is pretty consistent. I had some codes for the front view camera so I replaced it too. One piece of info I forgot to add is that I had a power tap to the mirror for a radar detector. I think that messed up the front camera and might have started all this. My next step is the HVAC module behind the glove box. 

  • Like 1
  • spayne460 changed the title to 2016 Sierra Headlights Turn Off At Night And Instrument Cluster Go Full Brightness

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • I agree with Tim.  As tech heavy as engines are these days, no way I’d be an early buyer of the new 6.6.  Of course, I bought my ‘26 Denali w/the 6.2 after dumping my Tundra with it’s defective 3.5 liter imploding engine disaster, so I’m a little gun-shy.  That said, my 6.2 has been rock solid.  I don’t drive it like I do my BMW Z4 M40i, but I don’t baby it either.  I got a V8 for a reason.  But I’m averaging 18 around town and 22 highway.  I have seen 24 highway as well when I wasn’t loaded up heavy.  Considering my Tundra with the twin turbo V6 only got 14.5 in town and 17 on the road, I’ll take the 6.2 all day, every day.  If I were you, I’d grab a ‘26 while you can.  Inventories are probably gonna start dropping and I’ll bet the deals will start looking sweeter as well.
    • I am curious if anyone has figured out a way to add an hard button AUX or 360 Camera switch to the center row of switches. I have a 2021 AT4, and want to split the hill decent button and add a 360 camera button so that you don't have to go into the center display and locate the camera functionality, etc...   My father's 2024 Yukon XL AT4 and it has a hard button, see below. I found this thread on the Yukons, but it seems like there may not be a part number for the 2021 sierras. https://www.gm-trucks.com/forums/topic/255339-adding-hard-button-for-camera-on-2021/ Anyone else figured this out. Seems like it would need to be a custom switch!   I am getting ready to install the auto stop/start eliminator, so would be nice to knock them out at once.     Upvote1Downvote0Go to comments
    • Looks like the entire state is burning. 😬
    • Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • Cool to see another Vermonter!
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...