Jump to content

Help with factory AM/FM/Cassette problem

blusteel_1

Recommended Posts

blusteel_1 New Member

blusteel_1

Posted
Posted

 

:banghead: I have a '95 Silverado Z-71 that has never been in the repair shop (273 k miles) and is a good truck except for the stereo. It blows a fuse every time I try to put a new one in. I can't figure out how to remove the stereo without the use of a saws-all and hammer, anyone have any tips on how to start with removal? Please help. :thumbs:

ManyCamaroz Enthusiast

ManyCamaroz

Posted
Posted

You must have a dead short in the power feed to your stereo.

 

Have you recently added any electrical components or did any electrical mods, pulled on any wires?

 

 

The wire insulation is probably nicked at some point under the dash or in the engine compartment. Before I removed the stereo, I would try to trace the hot wire from the back of the receiver to the junction block in the firewall under the dash and from the junction block in the engine compartment to the fuse block looking for any insulation damage. If you spot a skinned area tape it off with electrical tape and throw another fuse in it see what happens.

 

As far as removing the reciever... I have a Clymer Repair Manual for a '92-'96 GMC truck's and will look to see stereo removal is covered if you like.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Grumpy Bear
      Grumpy Bears 2015 Silverado 2WD

      By Grumpy Bear · Posted

      Fuel Update   6/7/2026   Since getting Pepper back I've been blending fuel. 50/50 E-85 - 93 pump gas. At my local pricing that is a 97 octane fuel for the price of regular and metering 48% alcohol.    This much gasoline octane locally is $10 a gallon with only one local resource!! I can blend this anywhere I find E-85.     Why? Longer range. Same no KR timing pull. More lubricious fuel. No loss in power cylinder cleanliness and a reasonable chance at seeing any future fuel dilution in the UOA's. When I blend with Shell or XOM premiums there is some friction modifier and antiwear enhancement. No cold weather starting issues either. So lots of pluses and few losses.     
    • Chuck FB
      Fluid Change Questions

      By Chuck FB · Posted

      That's certainly good to hear that there was nothing alarming on the cover magnet volume wise or chunk wise of metal. I don't recall if the Banks cover holds more oil than the factor cover, what volume did you estimate that it took ?. As to the transfer case I assume you bought whatever brand you wanted of a Dexron VI automatic transmission fluid.    Have you changed the automatic trans fluid at some point and actually I don't recall if your truck is the gas or diesel version as that makes the difference as to which transmission and oil type is required in 2023. The problem with my truck is that its the gas engine with the 10 speed and I've not yet attempted to see if I can drop the pan as the silly exhaust is right in the way and I do not want to touch the exhaust system on the manifold end if I can help it, the diesel does not have the Y pipe style exhaust under the pan so is not an issue to remove the pan.
    • Stacey Jaeger
      2014 GMC Sierra 1500 w/5.3L auto, 4wd, Crank but no start, 2MPA high pressure fuel reading

      By Stacey Jaeger · Posted

      I have a 2014 GMC Sierra 1500 with 5.3 litre, with 400,000km. I drove it one morning and when starting later in the day it would crank but not start. I figured it had to be the fuel pump, SO i replaced the low pressure fuel pump in the tank. The problem persisted the exact same way, crank but no start. Checked a couple plugs and was getting spark. I then replaced the high pressure fuel pump under the intake. But the same problem persisted, it tried to start right after the high pressure pump replacement for a few seconds but then just cranks. I plugged in a better scan tool with live data and I can see the low pressure pump has the proper pressure but the high pressure pump is only getting 1-3mpa, when the scan tool says it should be 14mpa. The scan tool says the lower pressure fuel is in the 55-60psi range and it hold this pressure when not cranking. But the scan tool shows the high pressure fuel drop down from 2mpa to 0.   I am not sure where to go from here, any recommendations or experiences with this condition? High pressure fuel rail sensor replacement?
    • Coastie05
      injector cleaner 2021 2.7 1500 silverado

      By Coastie05 · Posted

      Have you had any issues with your 2.7? I’ve only heard of a few with that kind of mileage so far.    OP, I haven’t read anywhere that carbon buildup is an issue. Just make sure to use top tier fuel. They claim that it’s better than non top tier. I’m not sure about that considering my FIL has delivered fuel for years and said it’s all exactly the same. 
    • Core-Lokt
      Fluid Change Questions

      By Core-Lokt · Posted

      It's raining on and off today, but I was able to change the rear oil and cover before it started. I ended up getting the Amsoil 75W85 for the front, 75W90 for the rear, and the right fluid for the transfer case. I wanted a cover with a drain, so that's pretty much the reason for the aftermarket one. I have a Roadmaster sway bar and had to fabricate 1" spacers for clearance, so that might be helpful if anyone has that on their truck and considering the cover swap. Old oil had 60,000 miles and just the slightest metal fuzz on the magnet; everything looked super nice. Fourth pic is just to highlight the spacers to accommodate the cover. Those bags sure make it easier than the old siphon guns.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...