Jump to content

Miller "chill"

Schmids5.3l

By Schmids5.3l
in The Off-Topic Bar

Recommended Posts

Schmids5.3l Senior Enthusiast

Schmids5.3l

Posted
Posted

My Girl friends old man gave me some Miller "Chill", the newer miller stuff in a green bottle, because he didn't like it. After about 5 of these they are tasting like Sprite. Lame. I'm not a fan of this beer. I have a few more left so I'm finishing them up :( but I won't ever buy this stuff!

C & A s Dad Senior Enthusiast

C & A s Dad

Posted
Posted

I have the same thoght about beer and coffee. I do not want any flavored, colored, sweetened, nothing added to either. Just plain old Michelob for the beer and good strong Community Dark Roast for the coffee.

 

I never will forget trying a Zima. It was like a light beer with an Alka Seltzer dropped in it.

thecraft Senior Enthusiast

thecraft

Posted
Posted

 

 

My Girl friends old man gave me some Miller "Chill", the newer miller stuff in a green bottle, because he didn't like it. After about 5 of these they are tasting like Sprite. Lame. I'm not a fan of this beer. I have a few more left so I'm finishing them up :( but I won't ever buy this stuff!
I HATE that s**t!
General Lee 01 Senior Enthusiast

General Lee 01

Posted
Posted

I actually like it. It's more tolerable than most of the other crap Miller Brewing Puts out. :(

 

 

 

 

 

 

 

You know what's entertaining as hell? Going back and forwarth from the age thread to the alchohol ones. :(

crpowens Enthusiast

crpowens

Posted
Posted
My Girl friends old man gave me some Miller "Chill", the newer miller stuff in a green bottle, because he didn't like it. After about 5 of these they are tasting like Sprite. Lame. I'm not a fan of this beer. I have a few more left so I'm finishing them up :( but I won't ever buy this stuff!

 

 

Personally, I think the girlfriends old man hates you. You took his baby girl! J/K :lol:

 

This kind of reminds me of someone saying "This tastes like Sh**, try it!"

 

Miller :(

Wingnut Senior Enthusiast

Wingnut

Posted
Posted

I've had it...Not bad for what it is.

 

There are WAY too many good beers out there to waste much time drinking that stuff though.

Schmids5.3l Senior Enthusiast

Schmids5.3l

Posted
  • Author
Posted

I agree with it's ''not too bad'', but I can't drink it in any sort of quantity, because it begins to taste like sprite/7 up. I'm like the Blake Shelton song 'The More I Drink'.... "If I have one I'll have 13" :sigh::thumbs:

Rosedog Enthusiast

Rosedog

Posted
Posted

Its the one miller beer that I like. I'm more a Bud guy, king of beers and all. For me its truely the all-around, any occasion beer....but...when I'm by myself and feel like a treat, I'll get myself either Alaskan, Sam Adams or some redhook ESB. The ESB leave me with a headache in the morning though.

 

Nothing beats "BEER" though! You know the one that comes in the white can that says "BEER". :P

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Artemis
      New Member Just Bought a Vtrux

      By Artemis · Posted

      Great info here thank you. I just joined, we have a 2014 Silverado truck we bought about 4 years ago with less than 5,000 miles on it. It has approximately 24,000 on it now. It appears to have all the standard issues that people are talking about. Occasional charging problems especially using 110 volt, occasional blinking triangle where nothing will turn on when first starting the truck but it will reset itself if you wait 10 to 15 minutes. Noisy coupler between the flywheel and the generator. Our truck is speed limited to 74 mph, is there any way to change that? The latest issue we have been dealing with is when driving long distance on the highway at full speed the generator does not keep the batteries charged. The meter will go into the yellow/red border Zone for charge status and the yellow triangle will illuminate solid but the generator will not keep the battery charged, not sure why the controller doesn't tell the gas engine to increase RPM to increase generator output it usually stays well below 25 kilowatts even though the battery is discharging and I have to slow down the highway to 45 mph and eventually pull over and let the truck idle to charge the battery so I can continue driving at speed. Has anyone had this issue before or have any idea how to diagnosed it? When via Motors was around it they were very helpful at troubleshooting. This becomes much if the Terrain is hilly and you're towing a small trailer
    • Z45
      Tonneau cover that does not leak water

      By Z45 · Posted

      I have the GMC accessory (REV) cover installed by dealer. Ordered with the truck.  They did a very good install job, can't find a single issue. Some water gets in around the tailgate but no where else.  You can see daylight around the tailgate but that's not the covers fault.  Installation is means everything. Guys at my dealer were seasoned pros, not inexperienced here today good tomorrow types, like many dealers employ for these jobs.   I don't mind paying for a professional job.    
    • Haufski762
      Tonneau cover that does not leak water

      By Haufski762 · Posted

      Like others have said, they will all leak. Mainly at the corners.   I have owned several and the best has been my current one. Revolver x4
    • calgator73
      LCA bolts

      By calgator73 · Posted

      About 8 months after an alignment job by the dealer I started experiencing a pretty significant clunk in the front end on hard left hand turns usually parking lot speeds almost at lock.  Occasionally get the same on hard rights too.   Discovered that the lower control arm attachment bolts are TTY and only to be used for a single use. And then I found some evidence of a TSB that indicates you can over torque those fasteners to about 130 foot pounds.   Asked a local shop to investigate and they found 3 out of four bolts loose and retorqued.   I've ordered the MOOG    K100421 lower control arm bolt kit that is completely reusable and not TTY.    Is the 80 ft pounds a realistic number?  Anyone have experience with those bolts?
    • davester
      Brake Bleeding Procedure on 2026 Silverado 2500

      By davester · Posted

      subscribe to alldata.com, that will have gm's brake bleeding procedure.  and what you have to do likely varies, as if you just replaced a caliper and the MC didn't go dry, you most likely can just do a normal bleed on that corner, but if you disconnected lines at the MC or the abs unit, or let the MC run dry while doing work, you'll have to do a more extensive/complicated bleeding procedure.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...