Cummins Swap

By devriesj39
October 31, 2009 in 1982-2005 Chevrolet S-10/Blazer & GMC S15/Sonoma/Jimmy

Recommended Posts

devriesj39

Posted October 31, 2009

hey i was wondering if anybody has of putting a 4 cylinder cummins into a mid 90's sonoma. just seeing if anybody has any insight on what might need to be done

txab

Posted October 31, 2009

You might look at this site. They might be able to help you

Here's one that is probably what you're looking for. It's a place to start anyway.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

Recently Browsing 0 members
- No registered users viewing this page.
Forum Statistics

250.3k
Total Topics

2.7m
Total Posts
Member Statistics

342,732
Total Members

8,960
Most Online

Newest Member
user087
Joined 10 hours ago
Who's Online 12 Members, 0 Anonymous, 869 Guests (See full list)
- newdude
- Another JR
- SoCal Angler
- BIGDOGx
- Gone Again
- NDKoze
- dji1
- Lyons00
- CRApex
- Flynlow
- KARNUT
- BuckWallace

Latest Articles
- 2027 Chevrolet Silverado: Horsepower, Price, and Release Date (What We Know)
  Yesterday at 12:36 PM
- 2027 Chevrolet Silverado First Official Look
  Tuesday at 03:00 PM
- GM Recalls 2,700+ Trucks For Airbags That Can Explode While Parked – How To Check Your VIN
  June 3
- You Can Completely Disable A New Chevy Traverse By Bending The Rear Wiper Arm (No, Seriously)
  June 3
Posts
- OEM Trailer Hitch Receiver - Impact tightened by shop
  
  By Another JR · Posted Just now
  
  Based on the service manual picture you posted, the four vertical bolts are single use and the torque specifications appear to be intended to be “torque to yield,” which permanently elongates the bolt. If they were torqued per that specification they should not be reused. However, if they used a properly limited impact device and only torqued them to the initial torque value of 89 ft lbs and did not do the final 70 to 80 degrees of additional rotation, they never yielded the bolts and they could be “reused” and torqued properly. The biggest issue in deciding whether to reuse them likely will be uncertainty over the torque applied by the impact driver.
- OEM Trailer Hitch Receiver - Impact tightened by shop
  
  By newdude · Posted 2 minutes ago
  
  No. If they were rammed in with an impact, they are stretched and need to be replaced. Hence one time use torque to yield fasteners.
- OEM Trailer Hitch Receiver - Impact tightened by shop
  
  By SoCal Angler · Posted 3 minutes ago
  
  Thanks newdude, that's what I thought. Since new bolts were used, can they retorque them without issue?
- Trans Cooler Thermostat Valve Body Seals - 2022 10L80
  
  By newdude · Posted 3 minutes ago
  
  In case you don't read these until later today... PPE makes me "think" that you have a 3.0 Duramax. Which you'd want quantity 4 of the 85628208 seal and NOT the 85628205. IF you have a gas truck 10 speed, you need one of the 85628205.
- OEM Trailer Hitch Receiver - Impact tightened by shop
  
  By newdude · Posted 6 minutes ago
  
  4 vertical bolts. They are one time use torque to yield fasteners and should not be re-used. Yes, they should be torqued to the proper spec.
GM-Trucks.com Clubs
- Black Truck Club
  
  Open Club · 612 members
- White Truck Club
  
  Open Club · 380 members
- Canadian Owners Club
  
  Open Club · 282 members
- Red Truck Club
  
  Open Club · 156 members
- diesel 3.0
  
  Open Club · 279 members
- Texas Owner's Group
  
  Open Club · 371 members
- NorthSky Blue Club
  
  Open Club · 118 members
- Midwest Owner's Group
  
  Open Club · 212 members
- 2015 Custom Sport Club
  
  Open Club · 5 members
- GM Snow Plowing Club HD
  
  Closed Club · 14 members
Popular Contributors
- Week
- Month
- Year
- All Time
1. 1
  
  KARNUT
  22
2. 2
  
  Atlas
  16
3. 3
  
  diyer2
  11
4. 4
  
  newdude
  10
5. 5
  
  Grumpy Bear
  10
Show More