Jump to content

Tpms Reset

ricci151
 Share

Recommended Posts

kdixer Enthusiast

kdixer

Posted
Posted

I keep my owners manual in the glove box just for instances just like this. :)

 

If you have keyless entry then hold lock and unlock on the remote at the same time for like 5 seconds or until the horn beeps. Then starting at drivers front let air out until you hear the horn beep then go to the passenger front and release air until the horn beeps, then the passenger rear, then the drivers rear.

mato27 Enthusiast

mato27

Posted
Posted (edited)

Each TPMS sensor has a unique identification code.

 

 

 

Any time you rotate your vehicle's tires or replace one

 

 

 

or more of the TPMS sensors, the identification codes

 

 

 

will need to be matched to the new tire/wheel position.

 

 

 

The sensors are matched to the tire/wheel positions in

 

 

 

the following order: driver side front tire, passenger side

 

 

 

front tire, passenger side rear tire, and driver side rear

 

 

 

tire using a TPMS diagnostic tool. See your dealer for

 

 

 

service.

 

 

 

The TPMS sensors can also be matched to each tire/

 

 

 

wheel position by increasing or decreasing the tire's air

 

 

 

pressure. If increasing the tire's air pressure, do not

 

 

 

exceed the maximum inflation pressure indicated on the

 

 

 

tire's sidewall.

 

 

 

To decrease air-pressure out of a tire you can use the

 

 

 

pointed end of the valve cap, a pencil-style air pressure

 

 

 

gauge, or a key.

 

 

 

You have two minutes to match the first tire/wheel

 

 

 

position, and five minutes overall to match all four tire/

 

 

 

wheel positions. If it takes longer than two minutes, to

 

 

 

match the first tire and wheel, or more than five minutes

 

 

 

to match all four tire and wheel positions the matching

 

 

process stops and you need to start over.

 

 

 

The TPMS sensor matching process is outlined below:

 

 

 

1. Set the parking brake.

 

 

 

2. Turn the ignition switch to ON/RUN with the

 

 

 

engine off.

 

 

 

3. Press the Remote Keyless Entry (RKE)

 

 

 

transmitter's LOCK and UNLOCK buttons at the

 

 

 

same time for approximately five seconds. The

 

 

 

horn sounds twice to signal the receiver is in

 

 

 

relearn mode and TIRE LEARNING ACTIVE

 

 

 

message displays on the DIC screen.

 

 

 

If your vehicle does not have RKE, press the

 

 

 

Driver Information Center (DIC) vehicle information

 

 

 

button until the PRESS V TO RELEARN TIRE

 

 

 

POSITIONS message displays. The horn sounds

 

 

 

twice to signal the receiver is in relearn mode and

 

 

 

TIRE LEARNING ACTIVE message displays on

 

 

 

the DIC screen.

 

 

 

If your vehicle does not have RKE or DIC buttons,

 

 

 

press the trip odometer reset stem located on the

 

 

 

instrument panel cluster until the PRESS V TO

 

 

 

RELEARN TIRE POSITIONS message displays.

 

 

 

The horn sounds twice to signal the receiver is in

 

 

 

relearn mode and TIRE LEARNING ACTIVE

 

 

 

message displays on the DIC screen.

 

 

 

4. Start with the driver side front tire.

 

 

 

5. Remove the valve cap from the valve cap stem.

 

 

 

Activate the TPMS sensor by increasing or

 

 

 

decreasing the tire's air pressure for five seconds,

 

 

 

or until a horn chirp sounds. The horn chirp, which

 

 

 

may take up to 30 seconds to sound, confirms that

 

 

 

the sensor identification code has been matched to

 

 

 

this tire and wheel position.

 

 

 

6. Proceed to the passenger side front tire, and

 

 

 

repeat the procedure in Step 5.

 

 

 

7. Proceed to the passenger side rear tire, and repeat

 

 

 

the procedure in Step 5.

 

 

 

8. Proceed to the driver side rear tire, and repeat the

 

 

 

procedure in Step 5. The horn sounds two times to

 

 

 

indicate the sensor identification code has been

 

 

 

matched to the driver side rear tire, and that the

 

 

 

TPMS sensor matching process is no longer

 

 

 

active. The TIRE LEARNING ACTIVE message on

 

 

 

the DIC display screen goes off.

 

 

 

9. Turn the ignition switch to LOCK/OFF.

 

 

 

10. Set all four tires to the recommended air pressure

 

 

 

level as indicated on the Tire and Loading

 

 

 

Information label.

 

 

11. Put the valve caps back on the valve stems.

 

 

 

 

Edited by mato27
PhilB Enthusiast

PhilB

Posted
Posted

A total PITA!! :) GM should come up with a more user-friendly way of doing this. The trick is to let air out for the first 5 seconds and then wait 30 seconds for the horn to beep. It may take several attempts at getting all of your sensors reset.

Spurshot Senior Enthusiast

Spurshot

Posted
Posted
A total PITA!! :) GM should come up with a more user-friendly way of doing this. The trick is to let air out for the first 5 seconds and then wait 30 seconds for the horn to beep. It may take several attempts at getting all of your sensors reset.

 

Yeah, like pushing a reset button on the dash to relearn all positions at once.

Matt_ Senior Enthusiast

Matt_

Posted
Posted
A total PITA!! :) GM should come up with a more user-friendly way of doing this. The trick is to let air out for the first 5 seconds and then wait 30 seconds for the horn to beep. It may take several attempts at getting all of your sensors reset.

 

Yeah, like pushing a reset button on the dash to relearn all positions at once.

 

 

it wouldnt be able to identify the sensor locations in that case. tpms systems that dont tell you the pressures at each tire have a single reset button.

 

honestly... its not that hard to do. ive reset mine numerous time for new tire/wheel combos and new rotations and ive never had it not work on the first try..... i really dont know how much easier they can make it......

brims Senior Enthusiast

brims

Posted
Posted
A total PITA!! :) GM should come up with a more user-friendly way of doing this. The trick is to let air out for the first 5 seconds and then wait 30 seconds for the horn to beep. It may take several attempts at getting all of your sensors reset.

 

Yeah, like pushing a reset button on the dash to relearn all positions at once.

 

 

it wouldnt be able to identify the sensor locations in that case. tpms systems that dont tell you the pressures at each tire have a single reset button.

 

honestly... its not that hard to do. ive reset mine numerous time for new tire/wheel combos and new rotations and ive never had it not work on the first try..... i really dont know how much easier they can make it......

 

 

I have never been able to get the air pressure method to work.

 

My mom's Jeep doesn't need to be relearned, there are receivers at each wheel well that pick up the individual sensors. A lot better system than the stupid thing we have.

Diesail Enthusiast

Diesail

Posted
Posted

I think it works great. I do the key fob thing and make a quick lap around DEFLATING each tire until I get the beep. Now that it has learned I make one more lap and adjust them to there correct PSI. Couldn't be easier IMO.

Wires Enthusiast

Wires

Posted
Posted

Ok, that's interesting info.

 

I didn't even realize that you had to do that......

 

I guess I need to make a journey to the garage and get-r-done....

zaemo Enthusiast

zaemo

Posted
Posted

I tried several times to get my '07 to relearn tire position. Took it to the dealer in in about less than a minute, the service rep had grabbed a hand held computer unit, pressed the Relearn Tire Position button, walked around and pointed the unit at the valve stems until the horn honked, and done. No charge. Don't know why I couldn't do it myself. Maybe I needed to try a few more times?

 

Z

Diesail Enthusiast

Diesail

Posted
Posted (edited)
I have tried many times to get mine to work. Never happened

 

 

Just rotated my tires yesterday, here are the steps I took

 

1) Got in the truck and set the parking brake.

2) Turned the key on, yes on and not running. Repeat, not the accessory position.

3) Pushed and held the lock and unlock buttons on the FOB until the horn beeped twice.

4) Stepped out and went to the driver's side front and using the end of a tire gauge deflated the front tire until the horn beeped.

5) Moved to passenger side front and repeated, then passenger rear and finally driver's rear. After the last tire it beeps twice.

6) Went back around and deflated or inflated accordingly.

 

One observation I did make, I have a 2500HD and tires are 80 rear and 60 front. The tires with 80 PSI deflated much faster and it took just a few seconds get a beep. The tires at 60 took MUCH longer to get the beep, so at the lower pressure of a 1500 I would think it would take even longer. Also you have a 2 minute limit per tire so that is why I think it much easier to deflate then to inflate as you can move around the truck faster.

Edited by Diesail
CalixEros Enthusiast

CalixEros

Posted
Posted

If you're having trouble getting it to work try running a large magnet across the sensor as you're letting air out. I do this on the Vette and don't even need to let any air out but I do on the truck. I have a friend's truck where I can just use the magnet, so I'm guessing there are differences in the TPMS that's making it easier for some than others... I got a big magnet from Harbor Freight for ~$5 that works great. An old speaker magnet would work well too.

cgalford Enthusiast

cgalford

Posted
Posted

I could never get mine to work and after A LOT of searching I found a service bulletin for certain types of valve stem type (rubber I think it was) letting air out causes a harmonic vibration so the sensor thinks it rolling instead of sending position information and that the programming tool was the only was to get them to register.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.3k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,739
    Total Members
    8,960
    Most Online
    chfkief
    Newest Member
    chfkief
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,374 Guests (See full list)

  • Latest Articles

  • Posts

    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      Fred was in the fertilized egg business. He had several hundred young pullets, and ten roosters to fertilize the eggs He kept records, and any rooster not performing went into the soup pot and was replaced. This took a lot of time, so he bought some tiny bells and attached them to his roosters. Each bell had a different tone, so he could tell from a distance, which rooster was performing. Now, he could sit on the porch and fill out an efficiency report by just listening to the bells. Fred's favourite rooster, old Butch, was a very fine specimen, but this morning he noticed old Butch's bell hadn't rung at all! When he went to investigate, he saw the other roosters were busy chasing pullets, bells-a-ringing, but the pullets, hearing the roosters coming, would run for cover. To Fred's amazement, old Butch had his bell in his beak, so it couldn't ring. He'd sneak up on a pullet, do his job and walk on to the next one. Fred was so proud of old Butch, he entered him in the City Show and he became an overnight sensation among the judges. The result was the judges not only awarded old Butch the "No Bell Piece Prize," but they also awarded him the "Pulletsurprise" as well. Clearly old Butch was a politician in the making. Who else but a politician could figure out how to win two of the most coveted awards on our planet by being the best at sneaking up on the unsuspecting populace and screwing them when they weren't paying attention. Vote carefully in the next election, you can't always hear the bells.
    • chfkief
      FS: Black Bear Performance AutoCal Tuning System

      By chfkief · Posted

      Do you still have?
    • 3CarSeatDad
      High Country Suburban build confirmation

      By 3CarSeatDad · Posted

      Can someone confirm if the GM order workbench terminal is able to validate a custom build sequence:   1) Initialize the Allocation Base: Open a new vehicle build queue, select the 2026 Chevrolet Suburban 4WD, and pick the High Country (3LZ Preferred Equipment Group).   2) Select the Diesel Powertrain: Go directly to the engine configuration screen and choose RPO code LZ0 (3.0L Duramax Turbo-Diesel). Ensure it maps to the MHS 10-speed automatic transmission.   3) Deploy the Seating Swap: Navigate to the Interior Options screen and enter RPO code ATT to replace the standard captain's chairs with the power-release 60/40 bench seat. Because you are not trying to force a separate luxury or air-suspension bundle, the standard, premium D07 Fixed Floor Console remains active. The system will accept this change immediately without triggering a warning message.   3)Apply Heavy-Duty Hauling Capability: Input RPO code NHT (Max Trailering Package). The commercial terminal will automatically bundle the required trailering hardware and software modules to support the diesel engine's maximum towing capacity.   5) Layer the Premium Tech and Glass: Separately add code C3U (Panoramic Power Sunroof) and code UKL (Super Cruise) to the order screen.   6) Run the Final Validation: Click the "Validate Order" button at the bottom of the interface.
    • revmanii
      Looking at ordering a '26 WT because I want a std cab, std bed

      By revmanii · Posted

      Spent the last hour or 2 googling and reading up on the spacer thing. I don't like the loss of thread contact on the slip on spacers, but it appears you can get "extended" lug nuts that reach into the hole of the wheel to get back the lost threads. Looks like the only true hubcentric slip on spacers are at least .375". I'd want as little as I could get away with and don't want to cause other clearance issues going any thicker. Bora seems to offer what appears to be a well made .375" spacer and extended lug nuts. I searched here and did find a couple threads recommending Bora. But not cheap. By the time I buy spacers and lugs, new TPMS sensors, then pay a tire shop to install the new sensors, I suspect I'm going to be in over $400. Thinking about running out and getting some washers to put behind the wheel to see if .375" is enough to clear calipers, turn lock to lock without rubbing, and to see if the wheels/tires look strange pushed out a little. This would just be to check fitment.
    • Core-Lokt
      Road Master Active Suspension

      By Core-Lokt · Posted

      Roadmaster makes some quality parts; I have their sway bar. I considered the RAS, but I ended up bagging. I didn't know what kind of ride I'd get with RAS, and the bags have interior jounce bumpers, so I can run 0 pounds pressure. I figured I'd have the best of normal suspension ride with assist on-demand. But it seems you got pretty much the same in one item.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...