Jump to content

1977 Glastron Carlson Cvx-20

ChevyMan23

Recommended Posts

ChevyMan23 Enthusiast

ChevyMan23

Posted
Posted

Like the title says, 77 Glastron Carlson CVX-20 jet boat, 20 foot 455 Olds punched out to 461.

All necessary engine work done to make it a reliable 455, i.e: oil restrictors.

Edelbrock/Mondello aluminum heads.

Weiand Intake, Holley 650 Marine carb

DUI Marine distributor.

Berkley 12JC pump, completly rebuilt, and machined by a professional, needs a Jet-O-Vater cable for trim adjustment, but can use the boat without it. (Just need it to make the killer roosters)

Hardin Marine gauges

Calrion Marine HU, 2 Pioneer 6x9's

New carpet, new upholstery, new windhsield(very rare) not made anymore.

Front seats will need to be rebuilt, but they're still useable as-is for now.

 

*Trailer included*

$6000

 

I know I am forgetting alot, but if you think of any questions, just ask.

 

 

DSCF1403.jpg

DSCF1401.jpg

DSCF1405.jpg

DSCI0105.jpg

100_1259.jpg

100_1262.jpg

DSCF1410.jpg

DSCF1411.jpg

100_1257.jpg

DSCF1400.jpg

ChevyMan23 Enthusiast

ChevyMan23

Posted
  • Author
Posted
You're forgetting the most important thing, location!

 

 

Sorry, Owensboro, Ky

Trav_13 Senior Enthusiast

Trav_13

Posted
Posted

Sharp Lookin Boat! I had a Glastron V-174 Boat up until 2 years ago. The Berkely Jet Drive is the only way to go in my opinion....mine had a 350 Chevy, it was alot of fun, but at the same time was starting to need alot of work....I sold it to a guy and his intentions were to restore it.

y2kz71 Enthusiast

y2kz71

Posted
Posted

wow thats a nice boat. My neighbor had one just like it back in the day. Price is great, this should sell fast.

  • 2 weeks later...
  • 1 month later...

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Z45
      Fluid Change Questions

      By Z45 · Posted

      I would be surprised if the diff's were not filled (with the cheapest gear lube) at the axle factory before being shipped to GM.  If you ever watched them building trucks they install the axles and all suspension parts with the frame upside down and then turn it over before its time to install the engine.     Too much gear lube in a axle can be worse than not enough especially with a lower quality GL where is get whipped up with entrained air (foam)  weakening its ability to lubricate.        
    • MORSNO
      Oil Consumption

      By MORSNO · Posted

      This is the 6.6 gasser section of the forum, you should either delete or modify your previous post as it is misleading for anyone looking for factual information on their 6.6 gas engine.
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Well....I've done my first intake gasket. Probably wrong, but...we'll see?   Ultra black on the china walls and 1/4" up onto the sides of the intake gaskets. Permatex High Tack (couldn't find Gaskachinch) on the head side of the intake gasket. I read wrong and it says you're supposed to put it on the mating surface of the head, not the gasket. Hoping it's like a PB&J sandwich where it doesn't matter what side the PB goes on so long as there's jelly. That crap is messy/sticky and I got a dab or two on the intake port openings, tried to wipe it off. Hopefully it won't be a big deal and will only aid in sealing.   Per instructions I left the intake (top side) of the gasket dry except for a light smear of RTV around the coolant ports. Wiggling the intake in there was a bear but I had help to free me of surrounding wiring/stuff but I was basically able to set it straight down lined up with the bolt holes.   I did not think to wait until the RTV skinned over but there probably was 5-10 minutes while it sat before installing the intake.   Bolts finger tight first. Then, followed the Chilton's manual pattern to snug them to 15 lb-ft.   Waited a little over an hour, and then did the final torque in sequence again to 35 lb-ft.   Yesterday I replaced the fuel pressure regulator and got my new "nut and bolt kit" (fuel lines) installed. Damn GM used security torx on the spider, which I don't have, so I got scammed at the local HW store for an off-brand security Torx bit set.   The new driver's door mirror arrived yesterday, so, there's a chance this thing could be running and road legal tomorrow? I don't want to get my hopes up.   This will be my first time stabbing a distributor, too. Although, lucky me, someone else marked the old distributor for removal previously, I did see that. (Someone's been here before!!). Engine is still at TDC so it *should* be just a matter of transferring the mark to the new dizzy and rotating it into place.
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      He has his dad’s newer truck he’s put away. He has several old cars he rotates between him and his family. I’ve seen a restored square body and a SS Chevy truck he’s sometimes drives. He did raffle off a new suburban recently. As much as he is watched if he drove new stuff as a rule we’d know it. It would be fine by me. I don’t care what people prefer. I got one more new one in me. I’d rather my wife get one. I can’t get her out of the Genesis. Don’t tell anyone. I want her to get an electric truck. I want to put a generator in the back. Just because. She hasn’t bit yet.
    • Atlas
      2027 GMC Sierra: Official Discussion

      By Atlas · Posted

      Yes, you must have seen my thread on the Blazer. HOT GARBAGE, but I love them anyway. I'm convinced every car guy has a soft sport for an S/T series somewheres. Probably even a Panther too, if I'm being an honest car guy. That doesn't mean they aren't junk. And they definitely don't get better with age. I sometimes play with old cars, but that's by choice. I don't rely on them and they aren't my everyday fleet.   Derek plays the common man on Youtube and that's no doubt where he started. Now he has Youtube money (and Motortrend, etc). You think his crews and his wife ride around in old beaters when they're chasing him and his wrecks across the country? No he's got newer and nicer stuff for that, you'll see glimpses of it in the footage.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...