Jump to content

What Ive Been Up To

sic lsx

By sic lsx
in Hobbies, Tech & Outdoors

Recommended Posts

sic lsx Senior Enthusiast

sic lsx

Posted
Posted

Ive been working on my camaro in afternoons and then going to bed so no time for the net lol. I installed a tubular k-member and a for 9" rear with , strange center section, 4.30 gears, 35 spline CM spool and 35 spline moser axles! I also had it narrowed a total of 5" so i could run a deep dish wheel. Here are a few pics. I also cleaned the bottom of the car and painted satin black!

 

71788_1623664881636_1536907746_31592642_2339125_n.jpg

61390_1586506392697_1536907746_31515710_4982588_n.jpg[/img]

61937_1586506592702_1536907746_31515711_7147962_n.jpg

62146_1586506792707_1536907746_31515713_8353091_n.jpg

 

This is after 1st coat! it has 3 coats

59971_1590166484197_1536907746_31522578_4618484_n.jpg

59984_1590166684202_1536907746_31522580_1062584_n.jpg

62488_1599815085406_1536907746_31543784_5025269_n.jpg

63836_1599815245410_1536907746_31543786_2006292_n.jpg

59971_1590166444196_1536907746_31522577_695043_n.jpg

62246_1590106962709_1536907746_31522504_4142913_n.jpg

 

 

 

here it is, 15x4 165/80s 15x10 5"bs 295/50s. just put a narrowed 9" in my car so had to get ne rear wheels :cool:

40122_1629377464447_1536907746_31602497_6830489_n.jpg

66337_1629376584425_1536907746_31602495_1659926_n.jpg

72741_1629375624401_1536907746_31602494_2929674_n.jpg

66339_1629374264367_1536907746_31602492_4787197_n.jpg

67679_1629373384345_1536907746_31602490_721601_n.jpg

72413_1629373144339_1536907746_31602489_5182273_n.jpg

sic lsx Senior Enthusiast

sic lsx

Posted
  • Author
Posted

thanks i hope to get a 10.99 put of it with the new parts. Going from a stock 10 bolt with 3/42's to 4.30s should help and took 40lbs off front of car. Ive been 11.3@120

sic lsx Senior Enthusiast

sic lsx

Posted
  • Author
Posted

clutch and a chrome molly drive shaft. Im going to snap the alu one. My goal is to get 6.0 iron block and build a 370ci turbo motor and run a single 88mm turbo

sic lsx Senior Enthusiast

sic lsx

Posted
  • Author
Posted

i use all UMI stuff but i got the BMR k-member at a deal used. BTW the 4.30's pull like a mofo!!!!!!! feels like i added a 100 shot lmao. 3.42s were really holding it back!

Wingnut Senior Enthusiast

Wingnut

Posted
Posted
clutch and a chrome molly drive shaft. Im going to snap the alu one. My goal is to get 6.0 iron block and build a 370ci turbo motor and run a single 88mm turbo

 

lol...I'm waiting to snap something on my drivetrain. Still stock axles, driveshaft (2 piece), stubs, hubs, etc.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
×
×
  • Create New...