Jump to content

Brake controller

rusty01

By rusty01
in Towing, Hauling & Hitches

Recommended Posts

rusty01 Enthusiast

rusty01

Posted
Posted

I have a Hayes Energize iii brake controller. I have it set up properly with the pendulum set with gravity. If I manual move the slider it applies the trailer brakes. Automatic does not work. No brakes at all. Is there something I am missing? I bought the controller used so maybe it's faulty? Anyone else have one of these controllers?

Hooverhog New Member

Hooverhog

Posted
Posted

I don't have a Hays controller but I just put a Tekonsha P3 in my truck and it works really well pulling my 6500lb. TT. It was easy to wire up too.

rusty01 Enthusiast

rusty01

Posted
  • Author
Posted

I got it work. I had to mess around with the little arm on the side of the controller to get it to work right. Now it slightly applies the TT brakes when going down hill to help keep speed down and applies the brakes increasingly as you get on the brakes.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      2020 Trailboss 6.2 replacement

      By newdude · Posted

      Correct.  2019-2021 model years are serviced by a different p/n.  19420611.  Recall 2021s use 19420611.   The recall engines 2022-2024 model years are serviced with 12740076.     The difference between 19420611 and 12740076 is GM changed injector size for 2022.  The injectors are smaller on 12740076 with smaller injector bores in the cylinder heads to match the smaller injectors.  So you can't install a 19420611 in a 2022-2024, and you can't install a 12740076 in a 2019-2021.     Both engines are the replacement engine p/ns that are in the L87 recall.  So both of these are the updated engines.     Here's a version of the L87 recall with the p/ns for all the parts needed.    RCRIT-25V274-7075.pdf   Note it shows 19420611 and 12740076 with an asterisk to a footnote "Use the VIN and the GM Electronic Parts Catalog (EPC) to determine which part to order if two or more part numbers are listed for the same part, as it may vary by vehicle options."    
    • 2017Z
      2020 Trailboss 6.2 replacement

      By 2017Z · Posted

      Looking for advice from this group. Took my flawless 2020 6.2 TB to an unnamed shop for routine rear brakes and oil change. Tech forgot to put oil back in after the full service and needles to say, destroyed my engine.  It’s all on their shop video so they are responsible.   I had my Chevy dealer do the analysis and they confirmed its compromised and said engine replacement. The manager said they only get GM reman engines from GM with full 3 yr warranty and the one they would put in is not same as what’s they are swapping out on 21-25 for recall.    I am looking for advice why that would be a different engine because obviously I had the good 6.2 year and replacing it has my concerns with that recall for 21-15   Also what’s the pros and cons of accepting the engine swap vs telling the shop that bricked the truck to pay up so I buy a new truck. I’m concerned about stigma resale eventually if I just decide to get rid of it after the swap or other issues showing up after the swap out.  
    • GN2018
      AFM Disabler Question

      By GN2018 · Posted

      Just looked up my records.  I've never gone over 5000 miles between oil changes.  At 46K miles, I have 10 oil changes.  I hope that will help.  I also installed the disabler last year.  I've still had a few times when it didn't seem to engage (which I can tell because the start stop feature kicks in), but for the most part, I think it's working.  For some reason, GM did not include the number of cylinders running in the information screen like I had on other models.  In my Cadillac, it shows me when it's running on 4 cylinders on the fuel milage screen.  I can't find that on my '21 Denali.
    • davester
      Wiring Help, Please

      By davester · Posted

      you might read through the info on gmupfitter.com for your truck, to find a good power source.
    • Grumpy Bear
      AFM Disabler Question

      By Grumpy Bear · Posted

      Melling I believe is/was the OEM on the lifters who explored this problem some years ago. The white paper they generated on the topic indicated two items of note when I read it. 1.) They only fail on the switch. Prevent the switch, prevent the failure. 2.) The majority fail due to deposits messing up the timing of that switch. Anyway that's what I got from it.    Mine have always been active, 195K+ now, and my oil maintenance is surgically clean.    Of course this assumes good parts. That is no heat treat issue or machining flaws. I get comfortable that these issues are in the rearview mirror by about 30K. IMHO naturally. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...