Jump to content

Factory remote start install instructions?

Sierramax07

By Sierramax07
in Modifications & Accessories

 Share

Recommended Posts

tbarn Senior Enthusiast

tbarn

Posted
Posted

Pictures won't post properly. But heres the rest. Installation Instructions Part Number

22901614

Kit Usage

This kit adds remote start to vehicles without option BTV. The vehicle must also have AQQ and an Automatic Transmission. Both can be verified by using GM Vehicle Inquiry System (GMVIS). For proper operation of the remote vehicle start system, a hood status-switch equipped hood latch is required. For light duty trucks, a jumper harness addition is also required in order to complete circuit 109, Hood Status Signal to the Body Control Module. Adding remote vehicle start also requires programming of the vehicle. This is done using the Service Programming System. The installer must call TCSC (1-888-337-1010) to obtain a VCI number. The TCSC will provide a Vehicle Configuration Index (VCI). The VCI is good for only one specific Vehicle Identification Number (VIN). You must have the vehicle’s VIN that will be upgraded and the Authorization Code from the label on the Installation Instruction Sheet included with the kit. This will allow you to access the software to enable the remote vehicle start option.

Kit Contents

Qty

Description

1

Set of Transmitter Key Fobs (2 in total)

1

Hood Latch Assembly (with switch pigtail)

1

Jumper Harness Assembly, including strap clip attached with blue tape (Light Duty kits ONLY)

10

Tie Straps (Light Duty kits ONLY)

1

Installation Instructions (including Authorization Code Label)

Note: Due to wire routing requirements on Light Duty Pickups, please review this entire procedure before trying to perform it.

Note: When calling the TCSC, you must use the Authorization Code from the kit and have the VIN available.

Special Tools, Equipment and Chemicals Required

  • Scan Tool (with capability of communicating on GMLAN)
  • Service Programming System (SPS – TIS2WEB, or equivalent)
  • J-46079 Tire Pressure Monitor Diagnostic Tool
  • GM Glass Cleaner or Cleaner-9M905449 (US) or 00992727 (Canada) – or equivalent
  • Silicone RTV 12378479 US or 88861419 Canada – or equivalent
  • 8” (20cm) ¼” diameter steel brake tube with ends cut a 45 degree bevel – for feeding wire through grommet
  • J-38125-22 wiring connector tool

Diagram for LD PU Harness Only

3419074.giftif.gif

This diagram outlines scope of the Jumper harness for Remote Vehicle Start accessory:

Front of vehicle (1)

Plenum (2)

Plenum Grommet (3)

Harness Ground (4)

Hood Latch (5)

Procedure Remove Front Compartment Front Sight Shield

  1.  

  2. Remove the front compartment front sight shield push-in retainers (1).
  3. Remove the front compartment front sight shield (2).
Updating the Hood Latch – Required for all non-UTJ Pickups

Harness is For Light Duty Trucks Only

3419291.giftif.gif

Route 3-way connector jumper harness branch (2) along front of vehicle, in preparation for routing under Grille Mount Panel Bolt (1) and Bracket (3). Be sure to route in front of air baffle (4). As a general guideline (after driver side of the hood latch) route alongside the Hood Release Cable up to the Driver Side Hood Bumper located on the Tie Bar.

For Light Duty and Heavy Duty Trucks

 

  1. Remove and replace hood primary and secondary latch. Refer to Hood Primary and Secondary Latch Replacement.

  2.  

  3. Make connection from the Hood Latch Pigtail (2) to 3-way forward lamp harness connector (1) (or Jumper Connector for Light Duty Trucks.)
  4. Ensure that the connection is securely fastened in the positioning locator for the connector. Refer to B55 Hood Ajar Switch.
  5. This Step is For Light Duty Trucks ONLY:

    Remove the 6.35mm hole clip with strap, which is taped to the harness (blue tape) and fasten harness (4) to the air Baffle (3) 6.35mm hole approx 4” (10cm) away from connector. Tighten strap clip and cut to length.

  6.  

  7. Remove and replace grille mount panel bolt (1).

    Tighten

    Tighten bolt to 25 N.m (18 lb ft).

    Note: Ensure the bolt does not pinch the jumper harness conduit when fastening.

Installation of the Hood Latch Status Signal Jumper Harness (For Light Duty Pickup ONLY)

Routing the 3-way Connector Branch of the Harness (Light Duty Pickup ONLY)

3420307.giftif.gif

Note: Use a tie strap, part number 11509086 (10 total in kit) to secure the harness to the hood latch release cable, after the hood latch, and before the hood bumper. Cut all tie straps to length.

Fasten the jumper harness to the Hood Latch Release Cable in one location along air baffle, using tie straps (1) P/N 11509086 from the kit. (midway between the two hood cable clips (2). Secure harness along hood release cable using two additional tie straps (3) P/N 11509086. Approx distance between tie straps should be 20cm. Cut all tie straps to length.

Routing the Ground Branch of the Harness (Light Duty Pickup ONLY)

 

  1.  

  2. Route the ground ring branch of the harness along the washer bottle tube and fasten using a tie strap P/N 11509086, to the forward lamp harness head lamp connector branch. Continue to route in front of the bottle and in front of the fog lamp bracket. Accessing from underneath the vehicle, continue to route behind the front fender and fasten to the upper end of the downward branch (2) of the forward lamp harness (1) using tie strap (3) P/N 11509086.

  3.  

  4. Continue along down to the ground stud G101 (1). Remove the ground stud and fasten using BOLT/SCREW-FORWARD LAMP WIRING HARNESS GROUND, tighten to 9 N.m for ground ring, noting there may also be an existing ground from the forward lamp harness. Cut all tie straps to length.
Underhood Routing of the Hood Latch Status Signal Wire (Light Duty Pickup ONLY)

 

  1.  

  2. Following hood latch cable, route the signal length of the harness (1), inserting the harness into the C-clips (2), in two locations.
  3. Using tie strap (3), P/N 11509086, fasten in two locations between C-clips, maintaining approximately 20cm between fastening points. Cut tie straps to length.

  4.  

  5. Fasten to the third hood latch cable C-clip and branch away and toward the body harness before the grommet (3). Fasten the jumper harness (1) to the body harness using two tie straps (2) P/N 11509086 evenly spaced approximately 20 cm alternating with clips. Cut to length.
  6. Route the signal wire conduit to the body harness grommet, ensuring to create a 3” diameter drip loop (4) before positioning the taped conduit end at the grommet for entry to the interior of the vehicle.
  7. using a utility knife, cut an 1/8” slit in the grommet (3) to prepare the entry for the bare signal wire.
Routing Wire through Grommet to the Body Control Module (Light Duty Pickup ONLY)

 

  1.  

  2. From inside the vehicle, remove the fasteners and position aside the instrument panel wiring harness junction block.

    Note: Junction block connector removal is not required.

  3. Using a utility knife, cut an 1/8” slit in the thin hole of the grommet opposite of the exterior side. From inside the vehicle, insert the ¼” brake tube (2) through the back piece of the grommet (3).

    Note: Grommet removal should not be required.

  4. From inside the vehicle, carefully push the tubing through to the front of the grommet, exiting at the exterior end of grommet.
  5. From the under side of hood, insert and feed the signal wire (1) and terminal through the tubing (2) to the inside of the vehicle.

    Be sure to maintain the conduit drip loop just before the grommet entry. Verify that the grommet end does not collapse.

  6. Remove the steel tubing (2) and clean both the entry and exit surfaces of the grommet using cleaner P/N 9M905449 (US), 00992727 (Canada), or equivalent.
  7. Apply silicone to the grommet at both wire entry and exit, using silicone P/N 12378479 (US), 88861419 (Canada) , or equivalent. Leave to dry while completing the remainder of this procedure.
  8. Using J-38125-22 tool, remove any wiring in K9 BCM X4 26-way connector pin 24 (BN/L-GN) and tape back onto the body harness, if applicable. Insert the GN (green) jumper harness signal wire connector into pin 24 on the K9 BCM X4 26-way connector. Refer to K9 Body Control Module X4. Reinstall all connectors.
  9. Reinstall the instrument panel wiring harness junction block to the floor studs and install the fasteners.

Programming the Vehicle (All Vehicles)

Note: For North America vehicles, the installation of accessory remote start requires BCM programming. This is done with a Service Programming System. The installer needs to call the Techline Customer Support Center (1-800-828-6860). The Techline Customer Support Center will provide programming instructions and changes to the vehicles calibration settings. You must provide the vehicle identification number (VIN) of the vehicle to be programmed and the authorization code provided with the accessory, when calling.

Reprogram BCM. Refer to Body Control Module Programming and Setup and follow Reprogram Control Module Instructions.

Learning Transmitters to Vehicle

Reprogram remote control door lock transmitters. Refer to Remote Control Door Lock Transmitter Learn

Reinstall all removed components.

 

  • 5 years later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      It also depends on what criteria someone is using for “best” when talking filters.  Are we going off best efficiency?   Best quality/QC?  Etc. because the two may not mutually exclusive.  
    • Tyler Gibbs
      PF63 Oil Filters Going Away?

      By Tyler Gibbs · Posted

      They’re not the same wiz as 10-15 years ago.  QC has fallen pretty hard.  The XP line was never good though in the first place.    https://bobistheoilguy.com/forums/threads/wix-filter-rusted-through.386492/post-6991372   https://bobistheoilguy.com/forums/threads/i-ve-used-my-last-wix-filter.27299/   https://bobistheoilguy.com/forums/threads/looking-for-a-better-replacement-for-wix-51258.403977/   https://bobistheoilguy.com/forums/threads/convince-me-in-using-the-purolator-boss.401537/post-7420147   the forums are littered with posts and examples of not great wix filters the last couple years 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...