Jump to content

Rattle/Clunk in steering column

xXZ-71Xx
 Share

Recommended Posts

xXZ-71Xx Enthusiast

xXZ-71Xx

Posted
Posted

Okay, Over the last year or so when I hit patches,pits,bumps etc. in the road my steering column has had a rattle/clunk in it. I have replaced the plastic steering column bearing and installed the latest ISS revision because there was a little play in it and I thought that would solve it but it hasn't.The play is coming from the inner shaft where the ISS bolts to under the dash. Any ideas on how to fix this?

 

 

Truck is a 03 Silverado 1500

xXZ-71Xx Enthusiast

xXZ-71Xx

Posted
  • Author
Posted

I replaced the upper shaft in the video (ISS) and the steering column bearing and it reduced the problem but didn't fix it. The play is coming from the shaft that the ISS bolts to and goes into the bearing. Thanks

sahls01gmc Senior Enthusiast

sahls01gmc

Posted
Posted

Mine has been doing that for 265,000 miles now. Hasn't got any worse.....

 

I've just gotten used to it at this point.

  • Like 1
ifixedit Enthusiast

ifixedit

Posted
Posted (edited)

Pretty common on these years. A friend of mine had the same problem on his 03, mine does it now and then as well. He said the local mechanic told him there's a sleeve of sorts that slides over the steering shaft as it comes out of the firewall. Although I have yet to investigate it to see exactly how it works, he says the sleeve is supposed to have some grease in it and it gets dry and hence the noise. He said there's a bolt that you take out so you can slide the sleeve back and forth to get the grease back in there and that solves the noise. Gonna have to check that out one of these days.

Edited by ifixedit
waumo1 Enthusiast

waumo1

Posted
Posted

Probably the same issue our 2002 Yukon had. They greased the slip joint 3 times before they finally replaced the whole thing under a "goodwill warranty repair".

Greasing it would make the problem go away for several months. I guess you could just keep doing that.

 

Ours was worse when turning to the left if I remember correctly.

Paulsoa New Member

Paulsoa

Posted
Posted

Had the same problem on my 03 as I recall.. There was a sb way back when. They greased it a few times always came back. Eventually just replaced it with a "redesigned" unit. Easy to do. There is a slip shaft 2 bolts slide it out and new one in. One right at steering box and the other is right up at the firewall if I remember correctly. Borgeson makes an upgraded unit

  • 1 month later...
xXZ-71Xx Enthusiast

xXZ-71Xx

Posted
  • Author
Posted

I had some things come up and forgot about this thread. I would like to thank everyone who responded but the part everyone is mentioning here is the intermediate steering shaft that I just replaced with the most recent redesign along with a new steering column bearing (green). I will try to take some pictures later to show what I replaced and where the movement is.

greatmizzou Enthusiast

greatmizzou

Posted
Posted

Mine has been doing that for 265,000 miles now. Hasn't got any worse.....

 

I've just gotten used to it at this point.

I had a GM mechanic tell me a long time ago that the steering rattle was nothing to worry about, but if it was too annoying they would pack it full of grease. Nobody packs it full of grease anymore supposedly because they don't have the right equipment to do it anymore, but he did offer a replacement that was expensive.

xXZ-71Xx Enthusiast

xXZ-71Xx

Posted
  • Author
Posted

I had a GM mechanic tell me a long time ago that the steering rattle was nothing to worry about, but if it was too annoying they would pack it full of grease. Nobody packs it full of grease anymore supposedly because they don't have the right equipment to do it anymore, but he did offer a replacement that was expensive.

Do you know if they were packing the intermediate steering shaft with grease or something inside the steering column?

greatmizzou Enthusiast

greatmizzou

Posted
Posted

Do you know if they were packing the intermediate steering shaft with grease or something inside the steering column?

I have no clue, I thought they accessed it somehow through the engine bay and that was it, so somewhere on the shaft. If I remember right, there was a special grease gun they used to get it all lubed up....not sure if he was pulling my leg on that though. There are numerous youtube videos about the same problem and different solutions.

xXZ-71Xx Enthusiast

xXZ-71Xx

Posted
  • Author
Posted

Okay the bottom thing circled in red is the top of the new intermediate steering shaft that runs down through the firewall (New with no play), The top thing circled in red is the new steering column bearing. The shaft circled in yellow bolts to the top of the intermediate steering shaft then runs up through the steering column bearing toward the steering wheel. The shaft that is circled in yellow is the one with play in it but I don't know how to tighten it up...It looks like the bearing is supposed to keep it from rattling but it doesn't. I checked my other truck and it moves to but only about half as much.

Untitled_1.jpg

  • 2 weeks later...
steveo77 Enthusiast

steveo77

Posted
Posted

I used to work for GM, the "solution" was to grease it in the early years, I'm pretty sure that they have a corrected part now as my 2013 does not do it. The part is called the intermediate shaft, and the posts are correct. Back in 2008 you could actually purchase the special grease gun for about 15 bucks. (It was a one shot tube that looked a bit like a toothpaste tube. It is accessed under the hood, there is nothing to tighten and no safety issue even though driving it can be a bit alarming.

  • Like 1
VikingTrad3r Enthusiast

VikingTrad3r

Posted
Posted (edited)

isn't this the typical issue where they disconnect the intermediate steering shaft and just pump it like jacking off to redistribute the grease?

 

yes i just said that, but its because thats what its like. i had same issue as OP and took me 10 minutes to do this. i do it once per year.

 

 

 

and this, though i didn't pump it full of grease. i just jacked it like vid above. works great.

 

https://www.youtube.com/watch?v=8W7TjXG_BAs

Edited by VikingTrad3r
  • 4 years later...
bigdogyj New Member

bigdogyj

Posted
Posted
On 10/6/2015 at 8:47 AM, xXZ-71Xx said:

Okay the bottom thing circled in red is the top of the new intermediate steering shaft that runs down through the firewall (New with no play), The top thing circled in red is the new steering column bearing. The shaft circled in yellow bolts to the top of the intermediate steering shaft then runs up through the steering column bearing toward the steering wheel. The shaft that is circled in yellow is the one with play in it but I don't know how to tighten it up...It looks like the bearing is supposed to keep it from rattling but it doesn't. I checked my other truck and it moves to but only about half as much.

Untitled_1.jpg

I know this is five year’s old but the solutions provided did not fix the OP issue. I have the same exact issue. I have a brand new Green column bearing as well as a new ISS.  But I still get the rattle/clunk and it seems to come from somewhere between the steering wheel and the column bearing.  I know I’m taking a long shot, but curious if the OP was ever successful in figuring out how to solve the issue. Thanks. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,961
    Total Members
    8,960
    Most Online
    CockneyUSA
    Newest Member
    CockneyUSA
    Joined

  • Who's Online   4 Members, 1 Anonymous, 756 Guests (See full list)

  • Latest Articles

  • Posts

    • Atlas
      Tire psi

      By Atlas · Posted

      It's possible the two trucks are using different body control modules which is why yours works and the OP's doesn't.   So much in these newer vehicles depends on model/trim configurations, production date. They don't all use the same modules like back in the day.
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I forgot to answer the question as per what market mine is set to and yes I finally found that area on mine and yes its also set to America.   So here's something I realized as I wasn't looking at that part in the Sierra section until now, your right that what I see here as choice 3 under Sierra which says 07/2023-06/2026 ( 433 MHz 13542523 ) it has no choice 5 for tire pressure selection. Where as it does under the Chev choice. However I kept going down the list within the Sierra and I am really wondering if choice 9 will work for your truck as it has the same model number and hertz sensor as my truck. I would say try that choice first, if that doesn't work then jump over to the Chev section and again choose that same model and hertz choice as for some reason the Chev section gives the choice 5 of tire type/pressure selection for going back a number of years. Could very well be an Autel thing that they just didn't get the updates all done properly under Sierra but anyway first try that selection 9 I suggested under Sierra and then go from there. 
    • B07
      Anyone have a spare?

      By B07 · Posted

      Looking for this piece that holds the hose clamp in place. I have the hose clamp just not that other piece. Dealers and wrecking yards in my area will not sell just that piece. They want you to buy the whole air tube $100 +/- to get that $5 part.  that piece isn't molded to the air tube as I looked at my friends truck. It's held on by a screw and nut. I'm trying to put the OEM parts on the truck as the previous owner butchered things up installing an aftermarket CAI. It really looked homemade. 🤣 Thanks
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      Ok I missed that part that yours is a GM. The strange part is that the choice for year ranges and within the year of 2026 is different on the Sierra then on the Chev for some reason as I am looking at my tool at the Sierra choices. Now I am guessing you see as to your sensor part number as it may be different on your truck for some reason and a call to GM should get you the part model number of the sensors you should have as well as which MHz your sensors are. I know mine are the ones as per what I listed but there are other choices in the Autel and got me wondering if by some chance they put different ones in your truck. Having said that, did you try using each of the choices starting from No 1 and going on down the list, not sure if that would mean shutting off the engine each time and resetting the tool and going at it again each time. Also I thought of something else which may sound retarded but if there was some stupid chance that the chev choice would work. The reason I say that is that the Sierra is showing a range up to 06/2026 for the various choices of sensors it could be where as the Chev has one choice that has that 12/2026. By the way it is possible to not run the truck and you may know that as per not pressing the brake but pressing and holding the start button for a few seconds and it lights up the dash ( its called service mode ) but that sucks battery power and if it were me doing it that way I would be throwing on a decent sized battery charger before doing it that way as killing your battery won't make you happy at me at all !.    Like I say, just a thought to try the Chev choices if you have already exhausted the Sierra choices but first it would be nice to know for sure what exact sensor model and hertz your truck uses as I assume only those choices that mention the sensor would work unless a choice that does not mention the sensor model would somehow work. Its frustrating when one is trying to use tools like this without the experience of the tool and the vehicle, as I am sure dealer techs themselves struggle with it when starting out or a new model year comes along that is slightly different. 
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      I tried before I updated the scan tool just incase an update messed it up, but it never worked so I updated the scan tool and it still didn't work.   Only difference is I click on Sierra not Chevrolet cause I have a Sierra.   If I click on 2026-2024 I didn't have any option to change placard, when I click on 2023 it does give me the option but when I try to do it,.it says vehicle not supported!   I have my region or market or whatever it is set to America I think, is that what yours is set to?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...