Jump to content

Headliner cleaning

BrandenG1

Recommended Posts

BrandenG1 Enthusiast

BrandenG1

Posted
Posted

My headliner and visors have a few dirty finger prints on them. What's the best way to clean them up?

sdeeter19555 Senior Enthusiast

sdeeter19555

Posted
Posted

Tuff Stuff foaming aerosol cleaner...I used it a lot at a detailing shop 20 years ago, still use it on my own junk.

 

Sent from my SM-T350 using Tapatalk

jgl25 Enthusiast

jgl25

Posted
Posted

Tuff Stuff all day! Just cleaned the previous owners grease stains off my headliner and it looks like it just rolled off the showroom floor.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • UrbanRage
      What have you done to your K2 today?

      By UrbanRage · Posted

      I have the same running boards on my truck and I do agree they are bulky. I also find myself stepping over them when getting in and out of the truck. Besides providing protection to the rocker panels, they aren't very useful.  I will be replacing them soon with the Amp Powersteps. 
    • ChristopherDobson
      Vehicle Payments

      By ChristopherDobson · Posted

      Monthly payment is only part of the equation. With today's prices and interest rates, I'd look at the total monthly cost: payment, insurance, registration, fuel, maintenance, and expected repairs. A vehicle that fits comfortably into your budget is usually the better choice than stretching for a higher trim. I've also kept my vehicles longer over the past few years. New cars have gotten expensive enough that driving one for 10+ years, while staying on top of maintenance, often ends up being the most cost-effective approach.
    • Grumpy Bear
      OCI, not when but why?

      By Grumpy Bear · Posted

      10 Ford and Chevy engines proven to reach 300,000 miles   You may note a common 3K OCI on this list of gas motors. I skipped over the diesels. Dh'O. 
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      Thanks newdude!  By the time manual selection is needed, I'm probably too much of a control-freak to depend on the transmission sensing braking to activate automatic downshifting.  I would be anticipating the situation and already be manually downshifting.   This truck replaced a 2004.5 LLY diesel with the Allison 5-speed.  Putting it in T/H made noticeable differences (when the torque converter locked, upshift points, downshift behavior).  On this 2024 gasser with the 10L1000 I haven't been able to detect much, if any, difference.  Ok, I can never tell now when the torque converter locks up.  But I also don't notice differences in shifting.  For downhills, I've probably already manually downshifted by then anyway.  Since it's also more awkward (than the 2004.5) to engage/disengage I don't even bother.  Or maybe it doesn't really matter with just a 3k lb. camper in the bed?   Thanks also for the list of reasons the charging system might select various voltages.  However, what I am seeing doesn't fall into any of those categories.  It very definitely, and very consistently, rises after coasting/braking.  Maybe not immediately, but not very long after coasting/braking.  Very consistently drops voltage when no longer coasting/braking.  It might also be interacting with the camper battery charging (I might disconnect the camper and see if it changes the charging behavior).  I also need to recheck turning on headlights for when I want to force it to charge the camper.   Another JR, in June I converted the camper to LiFePO4.  Since it's not a good idea to try to charge lithiums directly using truck, I installed a Victron Orion XS DC-DC charger (which BTW is AMAZING!!).  Being cheap, I only had to buy that one item (besides the battery, of course) to do the conversion.  The camper OEM 120v battery charger (only 19 years old and works perfectly) and the truck feed the input to the DC-DC charger (not at the same time).  But I didn't want the camper charger feeding back to the truck so I kept the old separator.  I considered replacing the separator with a 30amp diode but that means more work and might add another 1/2 volt drop.  One thing that surprised me was the voltage drop over the long 10awg wire run, so I can only charge smoothly at 8 amps (because the DC-DC charger is completely configurable).  Another reason I don't want an added voltage drop with the diode.  I might also be a little lazy but all this work is being done under the sink with a small cabinet opening.    
    • davester
      cam upgrade in CA

      By davester · Posted

      apparently CA smog is (or at least was)  checking that the vehicle is using the oem and/or a ca smog approved tune, so I expect you'll fail inspection doing it.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...