Jump to content

Recommended Posts

Posted

I've got a 2015 Silverado regular cab. I installed Razir's led tailgate light bar last summer. I decided to keep it on this winter for snowplowing, since it adds quite a bit of extra lighting when I'm in reverse.

 

This week the white wire that connects from the light bar into the left taillight tore apart. And with that, my reverse lights stopped working.

I spliced the two wires back together and heat shrunk them. Still.. No reverse lights.

I checked the fuses under the hood, and replaced the trailer reverse lights. I also checked the fuse panel under my dash, but I cannot find which goes to the reverse lights.

 

So does anyone know which fuse under the dash are for the reverse lights? And also why I would still not have reverse lights? (Yes, I do have taillights)

Thanks

Posted

Long shot but check Fuse 16 it is reverse lights for trailers according to my owners manual on a 17

I will continue to look for anything else

  • 1 year later...
Posted

Bumping this as I’m going through this.

 

did you ever find a solution?

On 1/11/2017 at 12:52 PM, Hult said:

I've got a 2015 Silverado regular cab. I installed Razir's led tailgate light bar last summer. I decided to keep it on this winter for snowplowing, since it adds quite a bit of extra lighting when I'm in reverse.

 

This week the white wire that connects from the light bar into the left taillight tore apart. And with that, my reverse lights stopped working.

I spliced the two wires back together and heat shrunk them. Still.. No reverse lights.

I checked the fuses under the hood, and replaced the trailer reverse lights. I also checked the fuse panel under my dash, but I cannot find which goes to the reverse lights.

 

So does anyone know which fuse under the dash are for the reverse lights? And also why I would still not have reverse lights? (Yes, I do have taillights)

Thanks

 

Posted
On 1/11/2017 at 2:12 PM, Nwatson99 said:

Long shot but check Fuse 16 it is reverse lights for trailers according to my owners manual on a 17

I will continue to look for anything else

What size is the fuse?

  • 3 months later...
  • 8 months later...
  • 4 years later...
Posted

Hi, lm new to the forum, and wanted to share something that will help quite a few 2014 to 2019 gm truck owners. If you are having the dreaded no power to fuses 16 and 33, the most likely cause is a non serviceable relay  inside the under hood fuse block.

You will need to purchase a new fuse block to remedy this issue. 

They cost from $150.00 to $220.00. It took me 15 min to replace and everything work normally now.

 

  • Like 1
  • 4 months later...
Posted
On 7/20/2023 at 12:19 PM, Dan Stephens said:

Hi, lm new to the forum, and wanted to share something that will help quite a few 2014 to 2019 gm truck owners. If you are having the dreaded no power to fuses 16 and 33, the most likely cause is a non serviceable relay  inside the under hood fuse block.

You will need to purchase a new fuse block to remedy this issue. 

They cost from $150.00 to $220.00. It took me 15 min to replace and everything work normally now.

Does anyone know what the part # is for this non serviceable relay that's inside the under hood fuse block?

Posted (edited)
8 hours ago, Kalei said:

Does anyone know what the part # is for this non serviceable relay that's inside the under hood fuse block?

You have to replace the entire under hood fuse block. The non serviceable relay is integrated into the fuse block. What year and make is your truck? It is probably going to be part # 84303175

Edited by mikeyk101
  • 3 weeks later...
Posted
On 1/11/2017 at 12:52 PM, Hult said:

I've got a 2015 Silverado regular cab. I installed Razir's led tailgate light bar last summer. I decided to keep it on this winter for snowplowing, since it adds quite a bit of extra lighting when I'm in reverse.

 

This week the white wire that connects from the light bar into the left taillight tore apart. And with that, my reverse lights stopped working.

I spliced the two wires back together and heat shrunk them. Still.. No reverse lights.

I checked the fuses under the hood, and replaced the trailer reverse lights. I also checked the fuse panel under my dash, but I cannot find which goes to the reverse lights.

 

So does anyone know which fuse under the dash are for the reverse lights? And also why I would still not have reverse lights? (Yes, I do have taillights)

Thanks

It's fuse

16 under the hood. I'm having issues with no reverse lights too. No mods though. Fuse is good (10 amp), both bulbs good, and camera quit too. Voltage is good at fuse, but not at the bulbs. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • 2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...