How do you install silverado 100 keypad entry GM 23473339

[jim larson]

How do you install this and program it. You will think the dealer would install it for free when buying a new truck. I found a Ford video on how to install their keypad.

 

 

 

But cannot find anything on this gm product.

 

 

https://www.gmpartsgiant.com/parts/gm-module-asm-keyless-entry-cont-install-23473339.html

 

Thanks

[Silverado Steve]

Contact your dealers parts department, they can get you the electronic version of instructions.

[Bmz72]

Sales and service are two different departments....those Technicians don't work for free just my .02

[Bmz72]

How do you install this and program it. You will think the dealer would install it for free when buying a new truck. I found a Ford video on how to install their keypad.

 

 

 

But cannot find anything on this gm product.

 

 

https://www.gmpartsgiant.com/parts/gm-module-asm-keyless-entry-cont-install-23473339.html

 

Thanks

see if this helps

Tools Required

Measuring Tape

Masking Tape

Before you start

Note: For the keypad to adhere best, the vehicle’s front door should be free of damage (dents, scratches, creases, fractures, etc.).

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Clean the area above the driver side door handle with alcohol wipe.

Programming and Mounting the Keypad to the Vehicle

1. Technician use a QR/Bar (QRB) Code reader and scan the QRB code from the Keyless Entry Keypad Wallet Card. You can also take a picture of the QRB code.
2. Transfer the file your computer (e-mail or cable transfer) to a folder.
3. Send file to TCSC along with the vehicle VIN and the Authorization Code from the Wallet Card. Make sure to include the following in the subject line: “Vehicle Vin Needs Updated to add the GM RF Keypad Programming and .csv files is needed for attached QRB Code”
4. TCSC will send you another file back. Place this file in C:\Users\your id\sps\type4.
5. TIS2WEB should now have the “BCM Cody Control Module – Accessory only Keypad Learn” option in Supported Controllers
6. Using TIS2WEB Program the Keypad.
7. Once TIS2WEB verifies the programming was successful, enter the 5 digit driver unlock code within 30 seconds. If the driver door unlocks, the Keypad was successfully entered.
8. Using Appendix “A” to find the suggested mounting location, prep the mounting location using the Alcohol Prep Pad.
9. Remove the red tape liners and press the keypad to the mounting location being careful to make sure the keypad is following the suggested body line. Use even pressure across the keypad to insure good tape adhesion.
10. Verify the keypad’s functionality using the “User Instructions.
11. Place the “User Wallet Card” and the “User Instructions” in the vehicle owner’s manual.

APPENDIX A Procedure

2. Starting from the driver side rear door edge (1) measure 157 mm along the door feature line (5) and position keypad (2).

   Note: Use masking tape to mark dimensions.

3. Starting from the door feature line (4) measure down 48 mm and position top edge (3) of keypad.

   Note: Use masking tape to mark dimensions.

4. Peel the protective liner from the adhesive backing on keypad and position to marked dimensions. Be careful not to touch the tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.

   Important: The adhesive will bond quickly to the paint. In the event that the keypad should be mis-aligned after installation, do not attempt to remove the keypad as this will cause paint damage. To avoid mis-alignment, do not drop the keypad into place. Instead, first align the top edge of the keypad to the referenced masking tape, then right outer edge to referenced masking tape. Then, toggle the keypad into place. Once the keypad is in place, press firmly on the entire surface of the keypad and then apply 15 PSI of equal pressure along the entire keypad to ensure good tape adhesion.

 

Diagram...

Attached Thumbnails

• 

• Like This

• Quote
• MultiQuote

[jim larson]

Who is TCSC? What is all that TIS2WEB about? Where is C/Users/your id/sps?type4?

 

This is confusing at best.

[x219c]

Who is TCSC? What is all that TIS2WEB about? Where is C/Users/your id/sps?type4?

 

This is confusing at best.

The short hand is that this has to be programmed by the dealer, according to those instructions. They have to send information about your truck and the keypad to GM to have it authorized... after that they can program it.

 

 

Sent from my iPhone using Tapatalk

[j13smiley]

I didn't even know gm offered this.

 

But yes - but those are all gm programming instructions. Only a dealer has access and the programmer. The dealer can't even do it themselves. .. they have to submit the files to gm who then sends back the program they use on the vehicle.

[sk]

There is also an entire thread discussing it here:

 

http://www.gm-trucks.com/forums/topic/195792-adding-keypad-keyless-entry/page-1