Jump to content

Can you install the 2019 dual exhaust rear bumper on a 2017 or 2018 Silverado 1500

Fredrico34

By Fredrico34
in Modifications & Accessories

 Share

Recommended Posts

  • 7 months later...
  • 2 weeks later...
Dezrado Enthusiast

Dezrado

Posted
Posted

Not a 2018 but im sure the fit would be closer than fitting it on an older truck like this one

7C3D3DE4-5FF9-4B0B-9838-1341F2A72805.jpeg

  • Like 1
  • Thanks 1
  • 3 weeks later...
MistercapNando Enthusiast

MistercapNando

Posted
Posted
On 9/10/2019 at 9:29 AM, Dezrado said:

Not a 2018 but im sure the fit would be closer than fitting it on an older truck like this one

7C3D3DE4-5FF9-4B0B-9838-1341F2A72805.jpeg

Is there any info on this mod? Like and cutting of the bed or modifications done? Looking to do this on my 2017 Silverado 1500 singlecab. 

jdm197 New Member

jdm197

Posted
Posted

only problem i see is where it wraps around. the shape is different and looks a little longer on the sides. would be easier to just cut the bumper you have and add the tips.

  • 3 years later...
Iron Joe New Member

Iron Joe

Posted
Posted

Hello folks, as there any issues with the fitting of the the 2019 pipes to the older model besides the tips. Hangers in correct locations, pipes fit around axles etc. thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Chuck FB
      Oil Consumption

      By Chuck FB · Posted

      Through the years it hasn't been my typical method as I tried to drop oil on an engine that was hot from having been worked, however that was not always practical and had to fire up a unit and let it warm up reasonably well and drop the oil when I had the time to do it but am referring to not only vehicles but a variety of farm equipment and highway tractors etc. However on a vehicle where one is crawling under it and the exhaust is nearby to ones body and if wanting to pull the plug without danger of being hit with boiling hot oil or attempting to remove a HOT oil filter, its sure safer and easier to not have everything smoking hot and can remove the filter right away when under the vehicle and let it all drain. Of course its not the end of the world if a bit of oil stays in the engine that might have eventually found its way out, I like to get out as much as possible but any oil changes that take place in shops would rarely be sitting around for very long at all before the plug is thrown back in and filter slapped on and oil poured in and sent out the door quick like. There would be very little time spent ( assuming they even did it ) in starting the engine with oil to fill the filter, then waiting to verify the level on the stick. A good reason to check ones oil level shortly after a shop changed the oil on a vehicle just to make sure its correct and to look under for any oil around the drain plug or filter. 
    • CPhelps
      4 Wheel Drive System

      By CPhelps · Posted

      Cool to see another Vermonter!
    • diyer2
      Winter Returned

      By diyer2 · Posted

      To many wildfires.
    • diyer2
      Oil Consumption

      By diyer2 · Posted

      I have changed oil and filter for years by starting a cold engine to warm oil up, let it run 5-10 minutes depending on temperature. Drain until it starts dripping, refill with quantity from owners manual or get it close.   
    • Chuck FB
      Fluid Change Questions

      By Chuck FB · Posted

      I changed the factory fill oil in the rear diff of my truck for the first time today and the miles is close to 9000 on the truck. There was a lot of fines on the magnet, a very thick layer but working it through my fingers it all felt like mush and as most know it appears like graphite, so no surprise chunks anyway. Certainly was time to do it from my thinking and could have been done sooner but the oil didn't look awful but sure wasn't new looking and never expected it to either. I did use some solvent to help me clean out the bottom area of the axle housing, just get any other stuff settled at the bottom washed and wiped out of the housing for the bit of effort it takes. I used Amsoil Severe Gear 75W90 in the easy packs to try out what they are like and I used up 4 packs and didn't spill much at all in the process but did take all four of the packs and go to the work bench and emptied them into a measuring container and there certainly was some in them that added up to something, then poured that into one of the easy packs and squirted in what I could get out of it. I would say the level is within 1/8th of an inch of being level with the threads at the fill plug so just the perfect amount. Once again, more than what GM says the fill volume is but computes with what others are adding to their rear diffs as well. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...