Jump to content

2020 GMC Sierra 2500HD Error Code P20EE

slimjim7772
 Share

Recommended Posts

jj46 Enthusiast

jj46

Posted
Posted
3 hours ago, xsvn2o said:

Mine has 6000 miles on it . Its been using a ton of DEF (30 plus gal so far) . after a few dealer visits I am about ready to try a ford . 

#troll

powerhaulic Enthusiast

powerhaulic

Posted
Posted
2 hours ago, davester said:

P0700 is just a generic error code meaning "the tcm has signaled the ecm that it's noticed a problem".

 

You need a more advanced code reader to get codes from the TCM, indicating the actual problem...

I am aware, thanks.

Thats why I said loss of communication, there were several codes for loss of communication. I believe there is a loose harness connection, probably at the body control module.

I could chase it, but why? i have a warranty, scheduled for next wednesday.

 

xsvn2o New Member

xsvn2o

Posted
Posted
On 10/15/2019 at 2:57 PM, jj46 said:

#troll

Believe me I wish I was . Hanging out on the internet is easier than endless trips to the dealer. 

xsvn2o New Member

xsvn2o

Posted
Posted
On 10/15/2019 at 11:36 AM, xsvn2o said:

Mine has 6000 miles on it . Its been using a ton of DEF (30 plus gal so far) . after a few dealer visits I am about ready to try a ford . 

* update . The dealer said that GM had an update that is going to fix the issue . Last tuesday they did the update and as of today (6 days later) no check engine lights and DEF appears to be being consumed at a normal rate . I have my fingers crossed this fixes it. 

Swell New Member

Swell

Posted
Posted

2020 gmc with p20ee code . Dealer reprogrammed today but buy the time I got home 40 miles or so it came on again anyone else had this happen

MrGraff Enthusiast

MrGraff

Posted
Posted
5 hours ago, Swell said:

2020 gmc with p20ee code . Dealer reprogrammed today but buy the time I got home 40 miles or so it came on again anyone else had this happen

Its a known issue, generally speaking clear the codes and go on down the road till GM releases an actual fix for it.

DVohs3 Enthusiast

DVohs3

Posted
Posted

I had mine done 2 weeks ago and about 400 miles. Not too many highway miles. My CEL hasn’t come back on yet. What kind of miles were the 40?  

JOZSEF New Member

JOZSEF

Posted
Posted

I have same issue p20ee

Got to dealer they sad it's fixed came back after 50miles 

Now they ordered a new nox sensor will see what happens

  • 7 months later...
Scottiek New Member

Scottiek

Posted
Posted
On 9/23/2019 at 8:43 PM, slimjim7772 said:

Purchased a brand new 2020 Sierra 2500HD 6.6L Diesel. The truck had ~400 miles on it when I left the dealership. I drove it for ~200 miles and the check engine light came on. Called Onstar for a diagnosis and they told me it was a P20EE error code. Took it to the dealer and was told this was a known issue and there was no solution although they had a Service Bulletin that said to reset the sensors, set it up for a regen and clear the code. The dealer said the code may or may not come back on. The next day the check engine light came on and I called Onstar again. They told me the same code P20EE. Called the dealer and was told to continue driving it, they said it would not hurt anything else and as long as the truck was running okay then everything was okay. In my opinion if the check engine light is on then the truck is not running okay. Contacted the GM Service Center and was told the same thing, that GM is working on a solution and to keep driving it until GM can resolve.

 

Now a couple of question: Has anyone else had this happen? Will it cause any damage or other issues in the future if I continue to drive the truck? 

This code just popped on my 2020 2500hd. This is the 3rd time the check engine light came on. 1st was for the fan regulator to cool the engine, which came on 2 days from driving it off the lot and the 2nd was for a heating coil. Has this code p20ee been figured out yet? Would like to know. Any had my truck for 3 months. Any help I would appreciate it. 

  • 5 months later...
  • 1 year later...
John5 New Member

John5

Posted
Posted

I have a 2020 3500 Denali and has been in the dealer once or twice a week for the past month for the same P20EE code. Updated software twice, removed and reinstalled software twice, changed NOX sensor twice, and cleaned MAP sensor once. Light stays off for about 60 miles each time. I'll just wait for GM to come up with a legitimate fix or get a lemon law attorney and hope they just replace with a 2023????????????    

davester Senior Enthusiast

davester

Posted
Posted
14 hours ago, John5 said:

I have a 2020 3500 Denali and has been in the dealer once or twice a week for the past month for the same P20EE code. Updated software twice, removed and reinstalled software twice, changed NOX sensor twice, and cleaned MAP sensor once. Light stays off for about 60 miles each time. I'll just wait for GM to come up with a legitimate fix or get a lemon law attorney and hope they just replace with a 2023????????????    

You might want to make sure the lemon law for your location still applies to the truck, as they vary by state and even location within a state.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...