Jump to content

Headlight Adjustment - Proper

Taz56
 Share

Recommended Posts

Taz56 Enthusiast

Taz56

Posted
Posted

I am curious on headlight adjustment if anyone knows. 

 

I am curious on headlight adjustment.

I own a 2019 GMC Sierra AT4. I Googled how to determine headlight height. I found this:

Park against a wall on a flat surface. Mark with tape or chalk the horizontal and vertical points of the headlights on the wall.

Back up 25 feet and adjust (if needed) so at 25 feet away they point in the same spot.

 

However in my case I do not feel this is any longer relevant as I have put bigger tires on and done a front end level kit. So my stance against a wall is no longer “factory”.  

Is there a "height" and “width” that I should aim for, Google is not being very helpful with that.

AD80 Enthusiast

AD80

Posted
Posted (edited)

Their should be a small dot or indentation on the front of your headlights  , marking the center. Measure from that dot to the ground.  Back up 25 away from the wall.  Your  light cut off point should be about 2" lower than your first measurement.  So if your headlights are 47" from the ground, the top of the cut off line should be 45" on the wall when 25 feet away.    I dont know if this is the official way to do it, but this is seems to be the way folks are doing it, and it should get you in the ballpark.   

Edited by AD80
  • Like 1
Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
27 minutes ago, AD80 said:

Their should be a small dot or indentation on the front of your headlights  , marking the center. Measure from that dot to the ground.  Back up 25 away from the wall.  Your  light cut off point should be about 2" lower than your first measurement.  So if your headlights are 47" from the ground, the top of the cut off line should be 45" on the wall when 25 feet away.    I dont know if this is the official way to do it, but this is seems to be the way folks are doing it, and it should get you in the ballpark.   

Sounds the same as what I posted. I assume the 2" you are referring to is to make up for the tires and leveling kit? 

aseibel Senior Enthusiast

aseibel

Posted
Posted (edited)

No, the 2" inches means your lights should be aimed slightly downhill. So 2" over 25' is only about 1/3 of a degree below horizontal. That should keep your low beams from blinding oncoming drivers.

 

your "instructions" are for people who don't own a tape measure apparently. You don't even need a wall. If you park in a flat area, measure the centerline of the bulb, then stand 25' away and measure the cutoff line again, it should be 2" less than the light bulb center.

Edited by aseibel
Taz56 Enthusiast

Taz56

Posted
  • Author
Posted (edited)
4 minutes ago, aseibel said:

No, the 2" inches means your lights should be aimed slightly downhill. So 2" over 25' is only about 1/3 of a degree below horizontal. That should keep your low beams from blinding oncoming drivers.

I get that, but what I was asking is, do I go "more than 2"" because I lifted my trucks front end and I put on bigger tires?

 

When I bought the truck lets say (for example only) that I was at 43" for the headlight, when I installed bigger tires and leveled the front end I am now at 49" Going down 2" brings me to 47" which is still higher than I was stock and I am still blinding people.

 

The point of this post was to ask what it should be at as I did not think to measure before I lifted the front end and put on bigger tires.

Edited by Taz56
aseibel Senior Enthusiast

aseibel

Posted
Posted
Just now, Taz56 said:

I get that, but what I was asking is, do I go "more than 2"" because I lifted my trucks front end and I put on bigger tires?

 

When I bought the truck lets say (for example only) that I was at 43" for the headlight, when I installed bigger tires and leveled the front end I am now at 52" Going down 2" brings me to 50" which is still higher than I was stock and I am still blinding people.

 

The point of this post was to ask what it should be at as I did not think to measure before I lifted the front end and put on bigger tires.

It doesn't matter what the old height was. As long as your lights are pointed downhill NOW, they shouldn't blind people unless you are tailgating them or parked directly behind at a stoplight/mcdonalds drive through.

 

forget about the "before" and just measure at the new light C/L and at 25' away. that's all that matters.

Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
Just now, aseibel said:

It doesn't matter what the old height was. As long as your lights are pointed downhill NOW, they shouldn't blind people unless you are tailgating them or parked directly behind at a stoplight/mcdonalds drive through.

 

forget about the "before" and just measure at the new light C/L and at 25' away. that's all that matters.

OK. Will do.

mafd2 Senior Enthusiast

mafd2

Posted
Posted

I can tell where the cut off point on the road should be on dim. I've set many sets and projector lights as well on lowered and leveled trucks.  I use a level slab and a brick wall to level the left and right headlights the same using the bricks or mortar joints.  Aim is perfect and I never get flashed.

redwngr Senior Enthusiast

redwngr

Posted
Posted

Whatever measure/adjustment method is selected, the verification is still how other vehicles respond.

 

Frequently getting flashed on level roads means they are to high. 

A head-on because a blinded driver that drifts into your lane can make for a bad evening. 

 

 

  • 9 months later...
JansterZ71 Enthusiast

JansterZ71

Posted
Posted
On 2/5/2020 at 9:26 AM, Taz56 said:

I am curious on headlight adjustment if anyone knows. 

 

I am curious on headlight adjustment.

I own a 2019 GMC Sierra AT4. I Googled how to determine headlight height. I found this:

Park against a wall on a flat surface. Mark with tape or chalk the horizontal and vertical points of the headlights on the wall.

Back up 25 feet and adjust (if needed) so at 25 feet away they point in the same spot.

 

However in my case I do not feel this is any longer relevant as I have put bigger tires on and done a front end level kit. So my stance against a wall is no longer “factory”.  

Is there a "height" and “width” that I should aim for, Google is not being very helpful with that.

Did you end up adjusting?

Taz56 Enthusiast

Taz56

Posted
  • Author
Posted
13 hours ago, JansterZ71 said:

Did you end up adjusting?

No. I meant to and kept forgetting.... I still want to LOL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By newdude · Posted

      HD at the moment, are kinda their own deal.  How LTZ sells on those vs on 1500, there is a difference.   They are merging most of the mid trims on 1500.  LT, RST and LTZ are replaced by one trim, Silverado.  LT and RST are a BIG portion of sales.    Bad naming choice aside, the new Silverado trim will offer the spread of options that those three trims offered.  So expect to see things like the tech package for example, and memory seats.  And LT Trail Boss will now just be "Trail Boss" (formerly LT Trail Boss) but will offer content spread like the new Silverado trim will.  The press photos showed the Trail Boss (formerly LT Trail Boss) has access to Super Cruise now, which on the current truck was High Country only.       Here is the Trail Boss interior.  Memory seats and Super Cruise are present.  All things the LT Trail Boss it replaces, and the RST it was based on didn't get on the current gen.  You had to go to LTZ or ZR2 for memory seats, and High Country for Super Cruise.      
    • dennismc
      2021 vs 2026 handling (1500 X31 Sierra)

      By dennismc · Posted

      I installed a Hellwig rear sway bar on my 21 Sierra SLT, it made a huge difference on how the truck handles, no body roll, the trucks much more planted now. Not sure of the suspension differences between the 21 and 26,  if its body roll your having a sway bar will solve it. 
    • Old Bay
      frustrating P0446 code

      By Old Bay · Posted

      So a follow up and my fix. I found in online searches the live data to look at on a scan tool to verify the fuel tank pressure sensor was working.  It showed an spec number towards the lower end of the rang, but in spec.  Then while it was running opened the gas cap and the pressure should change.  It didn't change even a tiny bit.  The data for the purge valve said it was open...never changed. So then I measured the voltages on the plug for the fuel pressure sensor and they matched what it should be.  So local car quest parts had the sensor in stock...it was a bit of a pain to remove and an even bigger one to get it to actually go back in.  It helped to unbolt the driveshaft and bungie cord away from the gas tank to give a bit more room to work. So fuel tank pressure sensor in I cleared the code, and started it up.  I went to the scan tool's live data and... Eureka! The pressure number was different and fluctuated a bit.  So took it on a short drive and pressure number varied saw the purge valve go from closed to open and back to closed.  Drove it to and from work for roughly a week plugged in the scan tool no codes.  I took it in to get tested and passed.  In my state's infinite wisdom (oops meant greed), since I pushed the test with the maximum extensions I have to take it back in by Feb '27 to 'get it back up to date', then my next test won't be until Feb '29. 
    • newdude
      loose lug nuts

      By newdude · Posted

      Any grease on the stud threads of any kind?   Wheel studs should have NOTHING on them for proper torquing and so the nuts don't back off.     Are all of the mating surfaces clean?  So wheel, rotor and hub?     We've had plenty of trucks at work with that wheel, this is a first to me.  Makes me think they've got a lube tech putting anti-seize on all the wheel studs or some kind of grease, and they need to stop doing that.  To have 11 other trucks with the same exact problem.      
    • Flynlow
      2027 Chevrolet Silverado: Official Discussion

      By Flynlow · Posted

      I was a Chevy guy for years, then switched to GMC because I liked the looks better.  I'm actually thinking I like the Chevy looks better than GMC for the first time in a lot of years.   One thing I know for certain, the new GMC dash is hideous!  Chevy wins this one!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...