Jump to content

2014 Sierra 1500 crew cab Remote Keyless entry “receiver” location

Jason Stephenson
 Share

Recommended Posts

Jason Stephenson Enthusiast

Jason Stephenson

Posted
Posted

I can’t find anything online nor in my Haynes manual for the location of the remote keyless entry receiver on my 2014 GMC Sierra 1500 SLE Crew cab. I’ve pulled apart the rear passenger door panel as well as the trim panel next to the rear window passenger side. Any help is much appreciated.

Jason Stephenson Enthusiast

Jason Stephenson

Posted
  • Author
Posted
20 hours ago, Jason Stephenson said:

I can’t find anything online nor in my Haynes manual for the location of the remote keyless entry receiver on my 2014 GMC Sierra 1500 SLE Crew cab. I’ve pulled apart the rear passenger door panel as well as the trim panel next to the rear window passenger side. Any help is much appreciated.

Found it. It in the rear over head just right (passenger side) of center, next to the rear window. Whenever in doubt, call your local service center and talk to the parts department.

021EFA89-5B74-4CE8-9D75-34F5260F144A.jpeg

  • Like 1
Jason Stephenson Enthusiast

Jason Stephenson

Posted
  • Author
Posted

Gonna wait until it starts acting up again then swap it to verify that’s what my issue was with my locks constantly locking. In another post, my trucks locks were acting crazy and constantly actuating and I narrowed it down to this thing or the Body control module. Fairly certain the receiver is the problem. I just started using my rear defrost and as you can see, the thing is butted up against the discharge.

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted (edited)

So, I was close on my first guess yesterday.

 

Are you going to put everything back together, and then strip it again if it is bad.

Could they tell you if there is a way to test it first? 

Edited by JimCost2014
Jason Stephenson Enthusiast

Jason Stephenson

Posted
  • Author
Posted
39 minutes ago, JimCost2014 said:

So, I was close on my first guess yesterday.

 

Are you going to put everything back together, and then strip it again if it is bad.

Could they tell you if there is a way to test it first? 

Gonna leave everything apart for awhile and hopefully we have a hard freeze again and I can get it to act up again then just disconnect/ swap to verify that’s the problem. Plus I get my fancy diagnostic tool (icarsoft CR pro OBD2) today and hopefully it tells me something. 

JimCost2014 Senior Enthusiast

JimCost2014

Posted
Posted
1 hour ago, Jason Stephenson said:

Gonna leave everything apart for awhile and hopefully we have a hard freeze again and I can get it to act up again then just disconnect/ swap to verify that’s the problem. Plus I get my fancy diagnostic tool (icarsoft CR pro OBD2) today and hopefully it tells me something. 

Specialty tools are cool, especially when they can solve a problem for you!!!

 

Good luck!

  • Like 1
  • 1 year later...
alaskajohn Enthusiast

alaskajohn

Posted
Posted

Did you ever solve your issue?  Mine is acting up as well, but the opposite problem.. it randomly stops working.  I've pulled the module out, and I think it might be an issue with the ground, but I can't figure out where the ground is located.

 

I get a 11.9v difference across the unit when it is not working, and a 12.0v difference when it is... which doesn't seem enough to create problems with the receiver, but I'm at a loss otherwise.

Here's the thread of my problem:  https://www.silveradosierra.com/electrical/2014-rcdlr-tpms-keyless-entry-intermittent-crewcab-t741673.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Another JR
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By Another JR · Posted

      Have considered installing a DC to DC charger in your camper to replace your isolator?  
    • newdude
      Gas fill door

      By newdude · Posted

      Common failure.  You need to replace the fuel door housing.   The painted cover transfers over to the new housing.  To remove the old one there is 4 spots where you poke the plastic to release it.  
    • newdude
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By newdude · Posted

      No such thing as regenerative braking on a pure ICE vehicle.     Regenerative braking is the re-capture of energy from electric motors and stores it in the battery pack.  So hybrids, PHEV and EVs have regenerative braking.     What you are seeing is the charging system changing modes is all.  Its likely entering charge mode for some sort of reason is all.  All of the charging modes will be listed below.   As for L10 vs D.  L10 turns off automatic grade braking.  L10 puts you in control of grade downshifts where in D it will automatically do it based on brake pedal position and other factors.  Otherwise L10 and D drive exactly the same aside from that one aspect.    Battery Sulfation Mode The BCM will enter this mode when the interpreted Generator output voltage is less than 13.2 V for 45 minutes. When this condition exists the BCM will enter Charge Mode for 2–3 minutes. The BCM will then determine which mode to enter depending on voltage requirements.   Charge Mode The BCM will enter Charge Mode when ever one of the following conditions are met:   Windshield wipers are ON for more than 3 s. Climate Control Voltage Boost Mode Request is true, as sensed by the HVAC control module via serial data. High speed cooling fan, rear defogger, and HVAC high speed blower operation can cause the BCM to enter the Charge Mode. The estimated battery temperature is less than 0°C (32°F). Battery State of Charge is less than 80%. Vehicle speed is greater than 145 km/h (90 mph) A current sensor malfunction exists. System voltage is determined to be below 12.56 V When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.   Fuel Economy Mode The BCM will enter Fuel Economy Mode when the estimated battery temperature is at least 0°C (32°F) but less than or equal to 80°C (176°F), the calculated battery current is less than 15 A and greater than −8 A, and the battery state-of-charge is greater than or equal to 80%. Its targeted generator output voltage is the open circuit voltage of the battery and can be between 12.5–13.1 V. When fuel economy mode is active, the generator is not charging, only maintaining open circuit battery voltage. The BCM will exit this mode and enter Charge Mode when any of the conditions described above are present.   Headlamp Mode The BCM will enter Headlamp Mode when ever the head lamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.   Start Up Mode When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 s.   Tow/Haul Mode (if applicable) Pressing the Tow/Haul Mode button located on the center stack, the vehicle system voltage is raised and the remote (non-vehicle) battery will be charged. Having the headlamps on will raise the system voltage and if the Tow/Haul button is applied it will not serve any purpose. The voltage is regulated between 13.9-14.5 V.      
    • jaszr2
      Active Grille Delete

      By jaszr2 · Posted

      Hello from Australia Just sharing that there is now a way to delete the active shutters entirely with just a plug in module. Opens up tons of room to light bars etc.
    • jake111
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By jake111 · Posted

      I have an observation and a question... 1) I watch the voltage closely because I have had to dial in the cut-in/cut-out voltages of the battery separator to my camper.  The "smart" charging drives me nuts.  Anyway, I noticed that when coasting for a while, and especially if lightly using the brakes (though not necessary), the voltage goes up from mid/high-13 volts to mid/high-14 volts.  Then it drops back down after stopping or going again.  Consistently!   The only explanation I can come up with is REGENERATIVE BRAKING!  Well, maybe that's a little bit of an exaggeration, but it's certainly free extra battery charging.   2) Driving on mountain roads I will use L and vary the max gear.  Things straighten out and I end up in L10.  Sometimes I leave it there for a while.  Is there any difference between L10 and D?   

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...