Jump to content

Center clearance light works intermittently

Mitchell Sloan
 Share

Recommended Posts

Mitchell Sloan Enthusiast

Mitchell Sloan

Posted
Posted

I noticed through the last few weeks of driving our 07 Silverado that the center clearance light lights up some times, and other times it’s black. The two outer lights never fail to work. Are these LED or are there bulbs that I can replace in them? Anywhere I should look for connectors or a replacement center light?

1D4B6836-C204-4F29-803B-E1359E635DDC.jpeg

Mitchell Sloan Enthusiast

Mitchell Sloan

Posted
  • Author
Posted
15 minutes ago, Formulabruce said:

Typically LED light bulbs do this, the 194 versions I use sure did.

Are the light bulbs replaceable or do I have to replace the entire center housing? 

Formulabruce Enthusiast

Formulabruce

Posted
Posted

My truck is the Classic style, which is not the same as yours, but I am betting they take a standard 194 bulb when new. Should be some screws on that housing ends. Make sure you put some clear silicone sealer around them when you re install.

Colossus Senior Enthusiast

Colossus

Posted
Posted

Those are LED.  They are not replaceable.  You have to replace the entire center module.

Mitchell Sloan Enthusiast

Mitchell Sloan

Posted
  • Author
Posted
5 hours ago, Colossus said:

Those are LED.  They are not replaceable.  You have to replace the entire center module.

Thank you! Tracked one down on 1A Auto. Will be ordering this week. 

Colossus Senior Enthusiast

Colossus

Posted
Posted

My pleasure.  I'd also recommend using some good silicone sealer around the outside of them.  They like to leak water into the cab when they get old. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • newdude
      Lower trims ( WT, Custom, Silverado ( aka LT )

      By newdude · Posted

      HD at the moment, are kinda their own deal.  How LTZ sells on those vs on 1500, there is a difference.   They are merging most of the mid trims on 1500.  LT, RST and LTZ are replaced by one trim, Silverado.  LT and RST are a BIG portion of sales.    Bad naming choice aside, the new Silverado trim will offer the spread of options that those three trims offered.  So expect to see things like the tech package for example, and memory seats.  And LT Trail Boss will now just be "Trail Boss" (formerly LT Trail Boss) but will offer content spread like the new Silverado trim will.  The press photos showed the Trail Boss (formerly LT Trail Boss) has access to Super Cruise now, which on the current truck was High Country only.       Here is the Trail Boss interior.  Memory seats and Super Cruise are present.  All things the LT Trail Boss it replaces, and the RST it was based on didn't get on the current gen.  You had to go to LTZ or ZR2 for memory seats, and High Country for Super Cruise.      
    • dennismc
      2021 vs 2026 handling (1500 X31 Sierra)

      By dennismc · Posted

      I installed a Hellwig rear sway bar on my 21 Sierra SLT, it made a huge difference on how the truck handles, no body roll, the trucks much more planted now. Not sure of the suspension differences between the 21 and 26,  if its body roll your having a sway bar will solve it. 
    • Old Bay
      frustrating P0446 code

      By Old Bay · Posted

      So a follow up and my fix. I found in online searches the live data to look at on a scan tool to verify the fuel tank pressure sensor was working.  It showed an spec number towards the lower end of the rang, but in spec.  Then while it was running opened the gas cap and the pressure should change.  It didn't change even a tiny bit.  The data for the purge valve said it was open...never changed. So then I measured the voltages on the plug for the fuel pressure sensor and they matched what it should be.  So local car quest parts had the sensor in stock...it was a bit of a pain to remove and an even bigger one to get it to actually go back in.  It helped to unbolt the driveshaft and bungie cord away from the gas tank to give a bit more room to work. So fuel tank pressure sensor in I cleared the code, and started it up.  I went to the scan tool's live data and... Eureka! The pressure number was different and fluctuated a bit.  So took it on a short drive and pressure number varied saw the purge valve go from closed to open and back to closed.  Drove it to and from work for roughly a week plugged in the scan tool no codes.  I took it in to get tested and passed.  In my state's infinite wisdom (oops meant greed), since I pushed the test with the maximum extensions I have to take it back in by Feb '27 to 'get it back up to date', then my next test won't be until Feb '29. 
    • newdude
      loose lug nuts

      By newdude · Posted

      Any grease on the stud threads of any kind?   Wheel studs should have NOTHING on them for proper torquing and so the nuts don't back off.     Are all of the mating surfaces clean?  So wheel, rotor and hub?     We've had plenty of trucks at work with that wheel, this is a first to me.  Makes me think they've got a lube tech putting anti-seize on all the wheel studs or some kind of grease, and they need to stop doing that.  To have 11 other trucks with the same exact problem.      
    • Flynlow
      2027 Chevrolet Silverado: Official Discussion

      By Flynlow · Posted

      I was a Chevy guy for years, then switched to GMC because I liked the looks better.  I'm actually thinking I like the Chevy looks better than GMC for the first time in a lot of years.   One thing I know for certain, the new GMC dash is hideous!  Chevy wins this one!  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...