Jump to content

Gm remote start install

Gregory Krisa
 Share

Recommended Posts

Gregory Krisa Enthusiast

Gregory Krisa

Posted
Posted

 

Hi I just received gm remote start part# 22997089

 

And are curious where I'm supposed to connect the green wire at.

I want to get all this done so that when I take it to the dealer all they need to do is turn it on. I assumed the truck was wired for it already seeing the plug near the hood latch but guess not. I'm assuming it's supposed to go-to the bcm but I have no idea where that is and what pin slot.

 

Thank you. 9950c5d6ee6a9dda0f5d5ccb78c63aa7.jpg5a5b51f25b981c1bc1382a49730a3733.jpg3e4a4ed38ff6e3624bc38e6c5df1a384.jpg

 

Sent from my Pixel 4 XL using Tapatalk

 

 

 

d53c8ab91de1664f813912e54552dcdf.jpg

newdude Senior Enthusiast

newdude

Posted
Posted (edited)

You've got the wrong kit for a 2016 2500HD if that is what you are tying to install this on.  22997089 is a Chevy 1500 kit.  

 

84424016 is the Chevy kit, 84424017 is the GMC kit.  Its just remotes, a hood latch and a recalibration authorization that the dealer has to install.  You also need to make sure your truck has option code AQQ before installing.    

Edited by newdude
Gregory Krisa Enthusiast

Gregory Krisa

Posted
  • Author
Posted
You've got the wrong kit for a 2016 2500HD if that is what you are tying to install this on.  22997089 is a Chevy 1500 kit.  
 
84424016 is the Chevy kit, 84424017 is the GMC kit.  Its just remotes, a hood latch and a recalibration authorization that the dealer has to install.  You also need to make sure your truck has option code AQQ before installing.    
Ok thank you.
Yea I want to do as much as I can my self hope it lowers shop price.
[emoji1751]

Sent from my Pixel 4 XL using Tapatalk

newdude Senior Enthusiast

newdude

Posted
Posted
13 hours ago, Gregory Krisa said:

Ok thank you.
Yea I want to do as much as I can my self hope it lowers shop price.
emoji1751.png

Sent from my Pixel 4 XL using Tapatalk
 

 

Its only 1/2 hour labor for the dealer to install it.  I know our dealer is $90/hr for accessories so it may vary near you. 

  • 2 weeks later...
CamGTP Senior Enthusiast

CamGTP

Posted
Posted

A straight shot with nothing blocking the signal I can get hundreds of feet away and it still works. Works through glass too, obviously.

 

Around buildings or anything like that and it's not going to work real well.

Xshot Enthusiast

Xshot

Posted
Posted

So pretty much the same as the standard fob.

Trying to decide if the simple install of this is worth the lack of range as compared to an aftermarket unit.

Gregory Krisa Enthusiast

Gregory Krisa

Posted
  • Author
Posted

I went with the factory because of it being tied in with on star and I believe the smart start vs onstar are about the same I'll disable onstar in may

Sent from my Pixel 4 XL using Tapatalk

Xshot Enthusiast

Xshot

Posted
Posted

"AQQ" is the code needed to for this work correct? Or is it "AP8"? I've seen both come up in threads about this and can't nail down which is required. According to the AC Delco list of RPO codes they mean the same thing..

 

fd7b62c31f8b23cf4013bf8d340a9a1d.jpg

  • 1 month later...
  • 2 weeks later...
  • 2 weeks later...
Xshot Enthusiast

Xshot

Posted
Posted

Should come with fobs, and paperwork and code, and a good latch.
Any wiring should already be in the truck if you have the appropriate RPO code

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • CaptPat51
      2021 Yukon Electrical Issues

      By CaptPat51 · Posted

      We tested the sleep mode with an ammeter in series with the negative battery terminal - 30amp fused - so we do know the actual shutdown and non-shutdown current draws and timing of the shutdown sequence.  We just have no protocol information to determine what module is issuing the network keep alive.  
    • Vu1can
      Brake Pad Warning Message

      By Vu1can · Posted

      TrueBlue...Even if you don't have that info stuff displayed, If Mr. Computer thinks there's something you should know about, it will pop up a warning message no matter what else is being displayed. I keep the speedometer displayed all the time, yet the brake pad message pops up anyway.
    • CaptPat51
      2021 Yukon Electrical Issues

      By CaptPat51 · Posted

      BTW, the 11.5amp draw is all the usual systems active - it's not a single draw - that's the "we're all awake" state of the vehicle - forinstance if the power steps are actuated, the draw will spike to 22amps for that operation.  when the battery is disconnected and then reconnected, the vehicle shuts down that one time only - and we see a 10-15minute progression down 11.5  10.5  9. 8 6. 5. 1.6... 500ma... and then off to sleep at 40 milliamp... as expected.  So we know it's a module that is simply refusing to allow the SDGM to proceed to the sleep state.  We do NOT think it is the telematics VIM module - since we already duplicated the problem with the "VIM bypass" solution installed (we reverted that since it also disables the gmc app - but it does not appear that the telematics system is the culprit).  We've replaced the rear heater control module, tested without the wireless charger, and the other modules on CAN Bus 5 - but still something is keeping us awake and removing X2 from SDGM allows sleep to proceed.  We cannot diagnose from OBD since OBD drops off at about the 9volt level in sleep mode and we can't communicate with the vehicle - also we can't trace the SDGM internal packets from the OBD side - we have Autel Ultra.   Any ideas on why disconnecting X2 would allow sleep to proceed appreciated.  This is no longer a repair situation - this vehicie is simply unusable in this condition and NOBODY at GMC Dealer can even understand what it is doing.  This is crazy.  We made these systems too complex and now we're paying the price.
    • CaptPat51
      2021 Yukon Electrical Issues

      By CaptPat51 · Posted

      Did this ever get solved?   I'm chasing 2021 Yukon Denali electrical issues - vehicle will not enter sleep mode - we can disconnect and reconnect the battery and it will sleep - but that's likely because we powered down whatever module doesn't correctly sleep.  once we start/accessory the vehicle and turn off, it will stay at 11.5 amp draw with something keeping the SDGM alive - it appears to be activity on the X2 segment, specifically CAN FD Bus 5 - but we don't know which device and we think we've already isolated all of the devices on that segment - so what keeps the BCM and/or the SDGM alive is unknown.   I don't yet have a packet trace from CAN 5 (and since this Global B we might not get much info from it) - but the vehicle has been down for 8 weeks and previously GMC Dealer was unable to resolve "kills battery" issues with this particular vehicle - so I'm at a loss - it seems to be beyond local repair capabilities - and the number of "telematics keeps vehicle from sleeping" posts indicates this whole architecture has major issues - I hate to say it, but we might have to install a battery cutoff switch on the front grill - one of those red boat switches - to turn off the vehicle.;)  Any pointers appreciated;)  I just bought a CAN FD interface and I'm planning to try Savvycan and Peak Can SW to triage this further.
    • bojanglespa
      2016 Sierra 1500 6.2L lifter Failure 🤨

      By bojanglespa · Posted

      Have had this truck for 7 years and it has 135,000 km on it. Have had no issues with it. Had 70,000 km when I bought it so I average about 9300km/year. The other day I started it to leave grocery store and felt a bad miss as I was pulling out of my stall. Rolled down window and heard the clatter. Limped it home about 1 mile and investigated further. Cylinder 6 misfire,  check engine light flashing and I believe traction control light on. The flattering gave it away in my mind. I did try swapping plug, coil and wire from 6 to 4 hoping the moss would move to 4 but no luck. Also compression dropped to 120lb when cylinder 1 has over 200lbs. Called tow truck to tow to local GM dealer. Failed lifter and 1 bent pushrod. Dealer changing lifters and pushrods on 2,4,6,8 and also VLOM. Think it may be time to get rid of this truck when I pick it back up from dealer. Dealer told me they do about 2 of these repairs every month.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...