Jump to content

2.5" motofab Install Photos

andrewb24

By andrewb24
in Modifications, Wheels & Tires

 Share

Recommended Posts

andrewb24 Enthusiast

andrewb24

Posted
Posted

I took off my 2" Rough Country lower strut kit and installed the 2.5" motofab upper which was a pain in the a&$ doing by myself.  I also installed a 1" block in the back awhile back.  Here are some after pics finally.  

 

 

Shouldve waited til I washed it but you cant see the dirt lol thats why I got a white truck.

motofab kit 2.jpg

motofab kit 1.jpg

thebrawns New Member

thebrawns

Posted
Posted

Why did you remove the rough country lower strut kit? I ask because I am looking into doing the same to my RST and was looking at the lower strut kit from rough country for the easy install.

 

Looks great BTW. Kinda wishing I had gone white but went with satin steel metallic myself.

SILVER SLED Senior Enthusiast

SILVER SLED

Posted
Posted

I tried the motofab 1.5" front lower shock spacer and it pushed the shock against the cv boot.  Seems like some  trucks rub and others don't.  

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
2 hours ago, thebrawns said:

Why did you remove the rough country lower strut kit? I ask because I am looking into doing the same to my RST and was looking at the lower strut kit from rough country for the easy install.

 

Looks great BTW. Kinda wishing I had gone white but went with satin steel metallic myself.

The lower kit is real close to CV axle and also wanted the extra .5" after adding 1" in the back.  My next color choice was satin steel metallic.

whewitt New Member

whewitt

Posted
Posted

What was the difference between the front and back height from the factory? My 2020 RST seems to only have a 1 inch drop in the front. (From the ground to the top of the fender is 37.5" front and 38.5" rear) I was considering going with the 2 inch Ready Lift in the front and a 1 inch block in the rear to keep it level. It seems like the rake seems to differ from truck to truck.

andrewb24 Enthusiast

andrewb24

Posted
  • Author
Posted
On 11/24/2020 at 6:54 PM, whewitt said:

What was the difference between the front and back height from the factory? My 2020 RST seems to only have a 1 inch drop in the front. (From the ground to the top of the fender is 37.5" front and 38.5" rear) I was considering going with the 2 inch Ready Lift in the front and a 1 inch block in the rear to keep it level. It seems like the rake seems to differ from truck to truck.

I didnt take a measurement when it was stock.  But it was .5" higher in back with the 2" rough country in front and 1" block in back.  Havent measured difference with the 2.5" motofab kit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      Gas Prices

      By Atlas · Posted

      87 down as low as $5.14 here... winning!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Progress... sort of.   Intake is disassembled, spider is out, fuel lines removed. Used a torch on the stripped screw with the lower intake off, much easier when I've got the intake sitting on my workbench, I made it talk. Walked right out with a pair of vice grips once it was nice and toasty hot.   New parts are piling up on my service cart waiting to be installed. Distributor, temperature sensor, new gaskets, fuel line kit, themostat, water neck.   My new pickle is I don't want to spend $600 on a replacement spider. I'm not sure IT is bad. I'm probably splitting hairs. Or it's $300 to send mine away and another 3 weeks of the truck just sitting. I have half a mind to assemble everything with the old spider to see if I can get away with just replacing the fuel pressure regulator to be safe. The obvious issue was the gushing high pressure fuel line which will be replaced. Getting to the spider really isn't that hard, and now I know what I'm doing , swapping it would be a breeze should it absolutely need one. Stupid, or smart?   The part that gives me pause is replacing the distributor. Well, it's already out. And I didn't mark it, whoopsie! Engine was at TDC when I removed it, I know that, so upon correct reinstall the metal tip on the rotor should point to the TDC mark on the distributor because that's where it was pointing on the old distributor. Worst case I'm a tooth off and have to re-stab it.   But then, what? I assume the truck will start. It doesn't appear the timing can be set. Here's the problem: These distributors can't be rotated but a degree or two, by design. What I read is Cam ****** needs to be -2 to +2 degrees, ideally at 0 (and checked/set above 1000 rpm). There should be enough wiggle to get that properly set, but checking the reported value is another potential issue. My Actron 9185 scanner says it supports enhanced GM PIDs and Cam ****** is one of them but it's unclear that I'll be able to correctly see it over OBD 1.5. I can see why people end up junking these things with life left in them. They're an absolute nightmare with tweener-year diagnostics/electronics and unobtanium parts.   Fingers crossed it starts and idles nicely. There can be hope, right? I'ma buy a lottery ticket the same day just in case.   Next steps..DO IT. I have not installed an intake before so I've been reading and watching a lot. Some say NO RTV except on china walls, some say DO RTV on water ports but not fuel/air intake. 1/4 or 3/8 bead on China walls? I think my strategy will be, obviously, RTV china walls with overlap on the gasket corners. Chapstick-style RTV the water ports. Leave intake ports dry. The only set of intake gaskets I could find locally are Edelbrock performance gaskets (uh...for an asthmatic 190hp V6? LOL) so we'll see how they do.   #NoToolLeftBehind. It took an hour, but my recovery mission for my deep 10mm socket was successful. It had rolled down the bellhousing and wedged itself between what I think are the fuel lines? I couldn't see it at all, but with a junk antenna I had laying around, I blindly went poking/sweeping for it, heard it clink, raised the truck, and caught a sliver glimpse of chrome with a flashlight way up there in Narnia. I had pushed it farther along the lines holding it captive, but within access of severely improvised tools, poking and cursing at it to finally knock it free to where I could get a fingertip on it to bring it home.    Not much to see.      
    • RyanbabZ71
      Gas Prices

      By RyanbabZ71 · Posted

      Thats crazy considering im right next door (Indiana)
    • Black02Silverado
      New Retail & Commercial Promo

      By Black02Silverado · Posted

      For a limited time, retail and commercial accounts receive an AMSOIL Vinyl Tool Tray with their order of $500 or more when they use code TRAY726 at checkout. The promotion runs through July 21, 2026.   Order at https://syntheticadvantage.com   Want to use AMSOIL in your business or sell at your store, apply here.  https://www.amsoil.com/business-opportunities/?zo=521390  
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      It wouldn’t have happened if the government hadn’t mandated outrageous fuel mileage standards. It does very little for the consumer. It adds cost. Back during Covid there was a chip shortage. They gave a rebate for your truck if it didn’t have the chip to turn on cylinder deactivation. It was 50$ because at best you may see 1/2 a mile increase per gallon. Splitting hairs each fuel mileage trick wasn’t mandated. The government doesn’t do the engineering work and say use this until it’s already in use and they like it. The fuel mileage was mandated. And those add ons the results. There’s a mandate and they are the results.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...