Jump to content

Recommended Posts

Posted

Purchased Tuesday 12/22/20.

Day 3 of ownership 12/24 - rained overnight and leaking back glass with service appointment scheduled for Monday.

Day 5 of ownership 12/26 - at 361 miles - check engine light, text from onstar and email that vehicle must be serviced within 7 days - code P026C.

 

I hope this is not a sign of things to come for sure.

Posted

16K trouble free miles to date. Took delivery  1-2-20

Posted (edited)

Mine sits waiting for parts - P20C1, DEF tank heater. 20K miles. This is the second CEL with limp mode warnings.

 

Edited by In2racn
Posted

In 1450 miles of ownership:

 

I had a slight DEF leak. They replaced the DEF injector and while in the service bay, they noticed and fixed an engine oil leak at the oil filter adapter. They replaced the adapter. No leaks now.

 

My only remaining issue is a rattle in the dash when first started up (cold engine). It goes away in about a minute of driving. I haven't taken it in for that one yet. It's a known issue (on the Duramax forum).

  • 1 month later...
  • 1 month later...
Posted

At 315 mile CEL came on with error code P026C (Chevy 3500). Took it to the GM dealership the next day. They said this was a known issue and GM was investigating. They cleared the code and sent me on my way. Within a few hours, the CEL came back on. Frustrating....apparently this is a common issue with the Chevy 2500/3500's and GMC 2500/3500's.

Posted

My 2021 Chevy 3500 Dmax has had check engine code PO26C started at 4K miles now passing 6k. Dealer can’t fix it. Also displaying PO22FB and P2AOO codes now. Already had it in the shop 3 times for this. Loss of time and couldn’t tow anything for 2 weeks so far this year. I’m very grateful for their little loaner cars but they don’t  replace a one ton work truck.

  • 4 weeks later...
Posted

Has anyone had this recurring P026C check engine code resolved yet?  Have a 2021 GMC Sierra 3500 Dmax as well that was purchased out of state due to no inventory in CA...threw a code on the way home to CA and now it can't be registered in CA due to smog requirement.  Spent $80k + on a truck that can't be registered.  I have GM case number assigned but getting ahold of anyone at GM is nigh to impossible.

Posted

check #20-NA-197:  this notice is for several trouble codes, fuel pressure sensor connnector may be poor connection.

good luck. 

  • 3 months later...
Posted
On 4/2/2021 at 2:26 PM, Andrew Reeves said:

At 315 mile CEL came on with error code P026C (Chevy 3500). Took it to the GM dealership the next day. They said this was a known issue and GM was investigating. They cleared the code and sent me on my way. Within a few hours, the CEL came back on. Frustrating....apparently this is a common issue with the Chevy 2500/3500's and GMC 2500/3500's.

 

8,500 miles and my CEL is still on. PO26c. Corporate and the Dealer are just passing the buck back and forth. I may call in a Lemon Law Attorney and then try a different brand. Only possible during the first year of ownership! After that you’re at the mercy of GM. They don’t seem to care what happens. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Welcome back! No, it definitely doesn't pass the sniff test. Even "ceasefire" needs an alternative definition these days.    $5.29 at Kroger today
    • That makes sense, and I think you are describing the real product problem. Capturing data is the easy part. If the owner or technician has to manually dig through five minutes of millisecond-level logs, the product has already failed. The device would be at the ECM harness, not at the OBD port, so I agree that data retrieval and event marking need to be thought through carefully. The way I am thinking about the architecture is: The recorder itself should not depend on a phone, app, Bluetooth, Wi-Fi, or cloud connection to capture the event. It should always keep a local rolling buffer and lock the event locally. A button, phone app, or small cabin device would only act as an event marker. If the driver feels a stumble and presses the button 10–30 seconds later, the pre-buffer has to already contain the useful data. For data retrieval, the practical options would be a sealed service USB lead, Wi-Fi download, or a phone/cabin companion device. I would not expect the owner to remove the ECM-side module or work with raw files directly. The cloud or AI side would be for interpretation, not for capturing the event. The truck may have no connection when the issue happens, so the evidence has to be saved locally first. After that, cloud processing could help decode the data, compare it against baselines, and generate a readable report. For the first version, I would keep the automatic triggers conservative and objective: driver event marker bus-off error passive voltage drop / brownout device reset FIFO or queue overflow a normally periodic message disappearing side-to-side communication mismatch, if the topology supports that For “learning normal,” I agree with your point, but I would not want to overclaim it as automatic root-cause diagnosis at first. A realistic first step would be learned baseline comparison for that specific vehicle and operating condition. For example, a value would only be compared against similar conditions: RPM range load / MAP throttle position gear / vehicle speed coolant and oil temperature battery voltage AFM/DFM state, if decoded and validated Then the report could flag things like: this periodic message disappeared compared with its normal timing this value deviated from this vehicle’s normal range under similar conditions the same abnormal pattern repeated after the same type of event the anomaly occurred together with voltage, oil-pressure, misfire, or communication changes But I would still call that “abnormal pattern detected,” not “replace this part,” unless there is enough validated repair data behind it. So the intended product would not be “here is a huge log.” It would need to be an event package: what triggered the capture how much pre/post data was preserved what changed before and after the event whether the device itself reset, overflowed, or saw a bus error selected graphs around the event raw data only as supporting evidence From your perspective, what would make this kind of report useful instead of just another datalog? For example: What are the top 5 parameters or events you would want highlighted first? Would you trust a learned baseline for that specific vehicle, or would you prefer fixed thresholds? How much false-positive flagging would be acceptable before you stopped looking at the reports? What would a one-page report need to show for an independent shop to take it seriously? For misfire, AFM/DFM, oil pressure, or U-code complaints, what would you want the tool to flag automatically?
    • 2024 Silverado 2500 HD LTZ grille no camera Parts list   84603331 84913656 84913657 84913654 84913655 84911567 84911568 85646092 85646093 85797921 85797922   11570637  x10-15   grille/bumper bolts 11546500  x10      grille clips 11571006  x10      push/retainer clips 11546454  x6       nut retainers 11611609  x6       M5 bolts 11610700  x6       molding/trim retainers
    • And use RA's 5% discount code if you buy from them.  google for the code, one is always available.
    • Just don't turn the steering wheel as much?
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...