Jump to content

C20 Driveline Carrier Bearing lubrication?

markdafedman
 Share

Recommended Posts

markdafedman New Member

markdafedman

Posted
Posted

Hey fellas and gals,

 

Got a 1984 C20 Custom Deluxe and have been making her roadworthy so I can put my tired '03 down for an engine OH.

Last weekend, I was lubing the suspension and could not for the life of me find a zerk for the carrier bearing. Is there a flush zerk that I should be searching for?

It concerns me because it is squeaking when the driveshaft is rotated. All I need is for the damned thing to seize up on me.

 

Any ideas short of replacement are much appreciated, but if R&R is the only cure, then so be it.

 

Thanks in advance.

 

<M>

txab Senior Enthusiast

txab

Posted
Posted

I haven't seen a carrier bearing that you could grease. It's always been a R&R for me. Now the slip joint  where the 2 shafts meet should have a zerk

markdafedman New Member

markdafedman

Posted
  • Author
Posted

Thank you- yes, the slip joint has a zerk, but replacing that carrier bearing looks like a real pain.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • marpel
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By marpel · Posted

      Although there is a "recommended" weight by those who sell trailers, my experience has been that they are way too aggressive in their information, for me at least. My '22 with 6.6 Gas, has a payload of about 3400 lbs and depending on your specs (I don't have 4WD so it has a bit higher Payload than others) yours will likely be different. Payload is one of the most important numbers for towing. Although you "could" tow the max trailer weight for your truck, I, personally, would not go close to that number. Having said that, a lot depends on how/where you will be towing. I live in the LMD of BC and often tow to Denver, Co, along interstates (flat and mountains) and I find I need to keep it in 5th (6spd) for the trip and travel at around 65mph. This is for a trailer dry weight of just under 3500lbs. If you are only doing local, short trips, it would not be that big an issue if you had a heavier unit. You will be surprised how much stuff you load the trailer with, so I would only recognize the trailers "full" GVWR weight rating, then decide on the appropriate trailer from that number. If you are worrying about how much stuff you should be putting in a trailer, you might have too large a rig from the get-go. Once again, depending on what terrain/distance in which you will be pulling. Marv
    • marpel
      Disconnecting Battery

      By marpel · Posted

      davester, Thanks for the response, how ever, I think I am now a bit more confused than I was before I posted - - After I posted, I actually found a YT video of a guy who replaced his Module (above tire) and he only disconnected the ground cable of the battery, but you describe rubbing the two cables together after disconnecting. I presume that is to do as you describe and eliminate any residual energy? - When I picked up the Module (between my posting and reading your response) from the dealer, I specifically asked about any re-programming and he stated it was not necessary as it was simply plug and play. Don't know how knowledgeable he is, though. - The video I watched also showed the Module plug to be difficult to "unlock" and remove, but there was no mention of silicone, although the video did show a bunch of dust/dirt in and around the plug (old truck) during removal. Are you talking about silicone that was applied by the factory, or silicone that you applied prior to plugging in? Thanks again, Marv
    • mandrautomotive
      2022+ GMC Hummer EV 40" Bumper Light Bar PRO: Factory Fit, Maximum Output

      By mandrautomotive · Posted

      Looking for a clean, factory-style lighting upgrade for your 2022+ GMC Hummer EV? M&R Automotive's 40" Bumper Light Bar PRO features a vehicle-specific, bolt-on design with no drilling or cutting required. Choose a bright white or yellow main beam, both paired with an amber DRL backlight for a sleek OEM-inspired look. The kit includes a curved LED light bar, powder-coated brackets, and all necessary mounting hardware.    Learn more or order yours See how it installs and looks on the vehicle:    
    • mandrautomotive
      🔥 2019+ GMC Sierra 1500 40" SLIM Grille Light Bar Kit – OEM-Style Fit, No Cutting or Drilling Required

      By mandrautomotive · Posted

      Looking for a clean way to add serious lighting to your 2019+ GMC Sierra 1500? Our M&R Automotive 40" SLIM Light Bar Kit was engineered to deliver maximum performance while maintaining a factory-inspired appearance.   Features: • Designed specifically for 2019+ GMC Sierra 1500 models • High-output 40" SLIM LED light bar • Clean, integrated grille-mounted design • No cutting or drilling required • Bolt-on installation using vehicle-specific brackets • OEM-style fit and finish   Whether you're hitting the trails, exploring backroads, or need additional visibility off-road, this kit provides powerful illumination without compromising the look of your truck.   For product videos, light output demonstrations, and installation content, check out our YouTube channel:   https://www.youtube.com/channel/UC3lutWP54fkXBl3iFLDJR-A Have questions about fitment or installation? We'd be happy to help.
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      $3.63 today. Inching down. Plenty still over $4.20 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...