Jump to content

2022 Tailgate

Bucket56
 Share

Recommended Posts

Bucket56 Enthusiast

Bucket56

Posted
Posted

It was my understanding that GM had fixed the issue of the fancy tailgate opening when there is a hitch in the receiver. Was I dreaming?

KennyL New Member

KennyL

Posted
Posted

I use a pin I got from Tailgatefix.com on mine. Easy installation. 

sheath Enthusiast

sheath

Posted
Posted

You can also hold the tailgate button for about 3 seconds, until the tail lights flash to quasi "lock out" the MultiFlex portion from opening.   Once locked out, to get it to function again you'll hold the button for about  3 seconds until the tail lights flash again.

Billh913 Enthusiast

Billh913

Posted
Posted

I purchased a B&W MultiPro Stow & Go hitch (TS20067BMP) that is made for this tailgate.  I set the height of the ball to work with all my trailers.  I love it.

Another JR Senior Enthusiast

Another JR

Posted
Posted
2 hours ago, sheath said:

You can also hold the tailgate button for about 3 seconds, until the tail lights flash to quasi "lock out" the MultiFlex portion from opening.   Once locked out, to get it to function again you'll hold the button for about  3 seconds until the tail lights flash again.

Very good to know!  Is this described in the owners manual?  Which “tailgate button” does this?  Main? Multiflex?  Dash?  Thanks

  • Like 1
sheath Enthusiast

sheath

Posted
Posted
10 minutes ago, Another JR said:

Very good to know!  Is this described in the owners manual?  Which “tailgate button” does this?  Main? Multiflex?  Dash?  Thanks

Yes, the 2022 Owner's Manual covers all the functions/switches of the Multiflex tailgate starting on page 27.  According to the OM on page 27, there are switches in the tail gate that don't allow the main tail gate to open if the inner gate is not fully closed.

Page 29 of the Owners Manual covers the "Multiflex Enable/Disable"  function.  It uses the top button (inner gate button).  

 

When I have the rear hitch in, I disable the inner gate, and so far, it has worked as advertised. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...