Jump to content

Interior Dash Issue

tybuch2003
 Share

Recommended Posts

tybuch2003 Enthusiast

tybuch2003

Posted
Posted (edited)

IMG_5364.thumb.jpeg.f4683702bd839e5609669ffc01a4a210.jpegHas anyone else had a problem with their interior dash? I have 2023 Silverado 1500 High Country Refresh that I got about two months ago. It has about 1,200 miles on it. I got the Jet Black/Nightshift Blue interior. I just noticed today on my way to work the black plastic towards the driver's side is raised slightly past the blue leather with stitching on the dash where they meet as part of the dash. This would be the black plastic that has the vents to do the defrost on the front windshield. You can push this area down with your fingers when you press. Is this suppose to be designed this way, or has the plastic slightly warped?

Edited by tybuch2003
Adding Picture
NE18 Enthusiast

NE18

Posted
Posted

Same issue Ford was having for a number of years. Might be one of those situations where you leave it because the next dash will do the same. Curious to know if others are experiencing this.

TNTSierra Senior Enthusiast

TNTSierra

Posted
Posted

I had this issue on my 2016 Sierra SLT. Dealership just replaced the whole plastic piece.  I didn't have an issue with it anymore. I'd get it replaced. 

  • Like 1
  • 2 weeks later...
tybuch2003 Enthusiast

tybuch2003

Posted
  • Author
Posted
10 hours ago, Daniel Formichelli said:

Odd although i as look at my dash in my 22. I noticed the speaker covers are doing the same thing.

Are you able to upload a picture of this?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • diyer2
      The Peckish Synapse

      By diyer2 · Posted

      She's laughing all the way to the bank.
    • newdude
      SLE 2.7L L4 shudders @ 2000-3000RPM

      By newdude · Posted

      There's a new PI on 2023-2026 L3B shudder.  Possible faulty front oxygen sensor.   Dealer can pull up PIP6060A and give it a read.  
    • newdude
      OBD not ready?

      By newdude · Posted

      Also here's the drive cycle for a 2021 Yukon with V8.  DO NOT USE THE CRUISE CONTROL WHEN RUNNING DRIVE CYCLE!!!!!:   Warning: Road test a vehicle under safe conditions and while obeying all traffic laws. Do not attempt any maneuvers that could jeopardize vehicle control. Failure to adhere to these precautions could lead to serious personal injury and vehicle damage. Note: You have completed this procedure when all parameters display Complete. Short stops for traffic will not affect the procedure. Note: Do NOT use cruise control during this procedure. Ignition/Vehicle » Off — For greater than 8 h Verify the scan tool parameter: Cold Start-Up = Yes If not the specified state Ignition/Vehicle » Off — For greater than 8 h & Repeat this step If the specified state Ignition » On / Vehicle » In Service Mode — For 1 min Engine » Idling — For 2 min Drive the vehicle while maintaining the following conditions for 20 min: Part Throttle Vehicle Speed = 24 to 97 km/h (15 to 60 MPH) Safely stop the vehicle Operate the engine/vehicle within the following conditions: Accelerate the vehicle to 64 km/h (40 MPH) Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 10% and 13% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 13% and 16% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 16% and 19% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 19% and 22% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Accelerate the vehicle from 64 to 97 km/h (40 to 60 MPH) @ Throttle position between 22% and 25% Release the accelerator pedal and let the vehicle coast down with the brake pedal released — For greater than 20 s Maintain steady state throttle at 89 km/h (55 MPH) — For 10 min Safely stop the vehicle
    • KARNUT
      2027 GMC Sierra: Official Discussion

      By KARNUT · Posted

      About the only GM that compares well with its competitors through the small to midsize vehicles is the Trax. I would like nothing better to just drive GMs. My wife in a Cadillac me in a Chevy minivan and Colorado. Part of my day is comprised of reading and watching comparisons of automobile. I could buy a car today. I’m back to research the next. 
    • newdude
      OBD not ready?

      By newdude · Posted

      Do you have any DFM defeat devices like the Range modules?  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...