Jump to content

ZR2/AT4X Part Numbers & Conversion Info

Epsilon Plus

By Epsilon Plus
in Modifications & Accessories

 Share

Recommended Posts

  • Replies 38
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Epsilon Plus
Epsilon Plus

Since the introduction of the ZR2 HD, many of us have waited for the parts to start hitting the market. They are now rolling out so let's build a thread where we can compile all the info on part numbe

Epsilon Plus
Epsilon Plus

I wish I could edit the original post as planned, but apparently that option times out. That said, here is some relative follow-up information from the larger discovery thread. This thread can serve a

Epsilon Plus
Epsilon Plus

Relevant torque specs:   Front Lower Control Arm Ball Stud Nut: First Pass 37 lb ft, Final Pass 90 -100 degrees    Front Lower Control Arm Nut [2x] First Pass 133 lb ft, Final Pass

Posted Images

  • 1 month later...
angel ullom Enthusiast

angel ullom

Posted
Posted (edited)
On 5/20/2025 at 5:12 PM, Epsilon Plus said:

Brake caliper torque specs:

Brake Caliper Torque Specs.pdf 859.29 kB · 10 downloads

Hey Epsilon I appreciate all the hard work you have done with providing the information do you think the ZR2 upper and lower control arms will work with the factory stock knuckle and if so would I need new nuts for the ball joints or are they the same nut size I appreciate it.

Edited by angel ullom
Need to ask another question
  • 4 months later...
calcagno21 New Member

calcagno21

Posted
Posted

This is a great write up and props for the work that went into compiling all of this. So in regards to the install. What is being done with the torsion bars themselves? Does the "lift" come from the geometry in the new control arms and knuckles? Are you keeping the torsion bars in the same position essentially then? Are you just adjusting until you get the desired 1.5" lift height?

kylant Enthusiast

kylant

Posted
Posted
15 hours ago, calcagno21 said:

This is a great write up and props for the work that went into compiling all of this. So in regards to the install. What is being done with the torsion bars themselves? Does the "lift" come from the geometry in the new control arms and knuckles? Are you keeping the torsion bars in the same position essentially then? Are you just adjusting until you get the desired 1.5" lift height?

exactly

  • txab pinned this topic
OS RR Enthusiast

OS RR

Posted
Posted (edited)
On 9/13/2024 at 9:56 AM, newdude said:

 

86591005 and 86591004 front flares, 85647450 and 85647449 rear flares.

 

86598488 and 86598487 front lower protector at the back of the front flares, 85543636 and 85543637 for the front of the rear flares, 85543635 and 85543634 for the back of the rear flares.  

 

Anyone know the part number for the attachment clips?

Edited by OS RR
  • 1 month later...
friasd New Member

friasd

Posted
Posted

hello everyone does anyone know if the fender flares from a 2024 GMC 2500 sierra AEV would fit a 2024 silverado 2500 AEV , that is the only thing missing from my silverado , i believe 

  • 2 weeks later...
kylant Enthusiast

kylant

Posted
Posted
On 4/2/2026 at 11:57 PM, friasd said:

hello everyone does anyone know if the fender flares from a 2024 GMC 2500 sierra AEV would fit a 2024 silverado 2500 AEV , that is the only thing missing from my silverado , i believe 

they will not. different shape

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.6k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,993
    Total Members
    8,960
    Most Online
    President Roberto
    Newest Member
    President Roberto
    Joined

  • Who's Online   0 Members, 0 Anonymous, 175 Guests (See full list)

    • There are no registered users currently online

  • Latest Articles

  • Posts

    • bwiese
      upgrading speakers on 2026 std cab WT...

      By bwiese · Posted

      I don't wanna do major surgery/upgrades, behind-the-dash work, add amps, change radio etc. on my '26 std cab WT. On the WT, it has the base 7" IOR infotainment setup, and only two speakers (doors). Since I listen to classical, looked around for speakers that do well and dug thru reviews. Two-way speakers were found to be better than 3-way. So I've ordered a pair of  Infinity Reference REF-9632IX 2 way speakers.  [These may  or may not have been discontinued / succeeded by the 3-way ...9633 ones.]    These speakers are lauded for 3 ohm and 94db sensitivity spec so they'll work well for ordinary base car radios without amps and offer better performance (quality,  strength) than  default base paper-cone speakers. They'll be installed in a few days and I'll let y'all know what I think. Bill W San Jose      
    • RyanbabZ71
      RyanbabZ71's 2019 High Country

      By RyanbabZ71 · Posted

      Thanks!   Changed out the rear shocks today to Bilstein 5100s.  So far feel much better. The stock Rancho were wore out.  Lots of heavy hauling (2 moves, home renovations, etc).  Next up is new BFG tires Monday.  Cant wait the current tires have little to no wet traction and are super loud (hum)    
    • Snowcamo
      No high speed fans...

      By Snowcamo · Posted

      Ok, I got the all the codes. What do you all think would be a place to start?
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      How about I just point to the factory pans stand pipe little drain plug and claim its a pan with a real drain plug !. I just couldn't swallow the fact that a Dorman pan which at this point is probably the only pan out there that fits the gas version truck cost that much up here in Canada so I decided initially anyway to skip it and see what I thought of pulling the pan method and down the road if I felt inclined enough then I would either install a drain plug kit in the factory pan if there is enough room for it, or have a bung welded onto it, or put an aftermarket pan on. The thing is if the pan is not pulled then the magnets in the pan can't be inspected and cleaned or if wanting to change out the filter. However of course it certainly would make the job easier to be able to drop the oil first before having to handle the pan if dropping the pan that go around was the goal.    I knew a guy locally that was doing custom field spraying years ago with a pickup pulling a ground driven sprayer, I believe it was a GM pickup with an automatic trans. He had a drain plug in his pan and would drop the oil out of it once a week and top it back up through the dipstick tube to keep refreshing a portion of the oil often and that made the transmission last far longer than had he done nothing. Soft fields pulling 500 gallons of water at the start of each mixed up sprayer tank batch and in low range sucking along. I imagine he got some tips from other custom sprayer outfits doing the same thing at the time and learning from their blown up tranny mistakes. Transmissions then had no lock up converter so would cook the crap out of the fluid slipping that much and it would not have been synthetic fluid either. 
    • KARNUT
      Gas Prices

      By KARNUT · Posted

      3.39 Kroger’s in Montgomery Texas. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...