Jump to content

Recommended Posts

Posted (edited)

Hi Gang,  

 

2021 2500

4wd

no oil use

no coolant use

16k

 

I realize this may be a dimwitted question, but the manual makes it way sound more "complicated" than any other vehicles i've owned in the past. Trucks or bikes.  

 

I have NO low coolant light, but as i check levels routinely, i see i should add a touch to get coolant up to the seam.  Can i just mix it and pour it in to the firewall coolant tank? 

 

Is there really a "leave the cap off, run the truck to temp, yada process etc"  that needs to be adhered too?  Again, gas engine, 6.6L8.  Can i not just top it off?

 

And for all those that say "just follow manual" [ which i don't disagree with ] thanks but still, insight would be appreciated and thanks folks.

 

 

Edited by Blatant
Posted
1 hour ago, Blatant said:

Hi Gang,  

 

2021 2500

4wd

no oil use

no coolant use

16k

 

I realize this may be a dimwitted question, but the manual makes it way sound more "complicated" than any other vehicles i've owned in the past. Trucks or bikes.  

 

I have NO low coolant light, but as i check levels routinely, i see i should add a touch to get coolant up to the seam.  Can i just mix it and pour it in to the firewall coolant tank? 

 

Is there really a "leave the cap off, run the truck to temp, yada process etc"  that needs to be adhered too?  Again, gas engine, 6.6L8.  Can i not just top it off?

 

And for all those that say "just follow manual" [ which i don't disagree with ] thanks but still, insight would be appreciated and thanks folks.

 

 

The process of running it up the point where the thermostat opens and the coolant flows is to make sure any bubbles that may be in the system due to a low coolant level are allowed to burp out to the expansion tank.  If that occurs, the fluid level would drop and you would top it up to the cold line again before closing the pressure cap.
 

If you have a slightly low level, it is very unlikely you have such bubbles in the system. With the system cold, add the amount of coolant needed to bring it up to the cold line, close it up, and drive normally. Check it again cold next time you think of it and add again if needed. You shouldn’t need to add more if there were no bubbles in the system. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 
    • "Life is getting back to normal."    I'm driving again and all new joints are operating as expected for this stage of recovery.   My most recent joint replacement still requires a lot of attention but experience has taught me that time will quiet the remaining pain.  I joked with my surgeon that another joint replacement would take my mind off my most recent surgery and he responded by saying the next will be a hip!  There are no plans for another surgery but, unlike me, I don't think he was joking!  I certainly wouldn't refuse further replacement  if required but hope to spend time out of the "post-op"  period.  I can't stress enough that if you have been recommended for total hip, knee or shoulder replacement that you welcome the offer.  Post-op "recovery" may sound daunting and painful, however, this is far better than the insidious erosion of mobility you are currently experiencing.  Imagine what it would feel like to wake up most mornings feeling better and more mobile than you did the previous day!  Prior to my first surgery in June 2025, even getting out of bed was becoming a formidable task.  Since the day after my first surgery, I get out of bed everyday easily and unassisted.  Making the switch to feeling a little better each day rather than a little worse, is hugely motivating!
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...