Jump to content

Snow tires

rjgvt

By rjgvt
in 2020-2026 Silverado HD & Sierra HD

 Share

Recommended Posts

rjgvt Enthusiast

rjgvt

Posted
Posted (edited)

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm.

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

Edited by rjgvt
  • Like 1
rdonarski Enthusiast

rdonarski

Posted
Posted

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the all-terrain tire option, and they seem to be doing just fine in the snow. 

rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

rdonarski Enthusiast

rdonarski

Posted
Posted
2 hours ago, rjgvt said:

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

As it would turn out, I checked this morning, and my closest Harbor Freight (50 miles away) doesn't stock them. Said I could go to the store, order it and have it shipped to the store for free (2 trips to store). Checked on shipping it - $6.99 - oh hell yes! Wouldn't make one trip for $6.99.

  • Like 1
Ejl923 Enthusiast

Ejl923

Posted
Posted

Been using the HF dolly for years.  Hurt my back 20 yrs ago and this allows me to lift/rotate tires.  The fact that the tire can be spun to line up lugs is the best thing.

  • Like 2
Johnsondavid New Member

Johnsondavid

Posted
Posted (edited)
On 9/12/2024 at 7:31 AM, rjgvt said:

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm. Geometry Dash Scratch

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

I like your idea. Replacing new wheels will help the car operate better and above all it provides safety when moving.

Edited by Johnsondavid
revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
On 9/12/2024 at 7:38 AM, rdonarski said:

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the [b]all-terrain tire option[/b], and they seem to be doing just fine in the snow. 

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Edited by revrnd
  • 2 weeks later...
revrnd Senior Enthusiast

revrnd

Posted
Posted

This comment came to mind yesterday after reading the good & bad comments about Michelin's quality in the other ongoing tire thread in the Silverado HD section.

 

My brother had 2 sets of Michelin LTX M+S tires on his 2016 2500 Sierra HD. He was happy w/ the tire wear on the 1st set, however the 2nd set wore out faster than expected. 

 

His set up and/or usage hadn't changed. Talking to the tire shop, they said that they had seen the less than satisfactory tire wear from Michelin tires.

rdonarski Enthusiast

rdonarski

Posted
Posted
On 9/19/2024 at 9:35 PM, revrnd said:

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Thought I responded to this, but don't see it. Yes, they are the Transforce ATs. They have worked fine for me in the winter, but with this being my 'Till death do us part' truck, I try to minimalize winter use.

revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
2 hours ago, Hoginedgewood said:

Will you have to use a tpms relearn tool every spring and fall?

 

 

Yes. This is the relearn tool that I picked up on Amazon. It works fine w/ the GM sensors. 

 

20241006_205615.thumb.jpg.12a1633d74c89c49440e77b0df3dcb7a.jpg

 

My set of winter rims have aftermarket Schrader(?) sensors & the truck wouldn't recognise them. My local garage was able to 'match' 1 of them to my truck using their Snap-On 'tool' so I'm hoping once they do the rest, my tool will work when I do the swap in the fall.

 

I'll try to remember next month to post.

Edited by revrnd
rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

I have used an Autel TS508 to relearn the TPMS sensors on my previous 1500’s. I used it to program the tire placard pressures to 55psi front/rear on my 2024 AT4 HD. Will use it to relearn the sensors when I take off the KO3’s and put on the snow tires/wheels.

  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted

I spent 2 years in the Rockies in a 1975 Ford Ranger 2WD....it had studded tires on the rear and I stuck 2 manhole lids in the bed....I was actually quite surprised how well the truck did in the snow and ice.....I remember trying to beat the snowplow going up highway 285 on way home at 5 in the morning.......2-4in of dry colorado powder is like driving on asphalt compared to the plow scraping down to the ice.....studded tires are awesome

revrnd Senior Enthusiast

revrnd

Posted
Posted

Studded tires are fine where they're legal.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,982
    Total Members
    8,960
    Most Online
    nolankd
    Newest Member
    nolankd
    Joined

  • Who's Online   2 Members, 1 Anonymous, 438 Guests (See full list)

  • Latest Articles

  • Posts

    • Black02Silverado
      New Retail Account Promo

      By Black02Silverado · Posted

      For a limited time, retail accounts receive a free fender cover (G2803) with their order of $750 or more when they use code FENDER926 at checkout. The promotion runs through Sept. 8, 2026. Own a business and want to apply for a retail account?  Apply here. https://www.amsoil.com/business-opportunities/sell-in-your-store/?zo=521390  
    • Chuck FB
      Correct way to service 2024 l8t allison trans?

      By Chuck FB · Posted

      Thanks for that, yes just because I could I measured what came out just to give me some guidance although I already knew to expect it to take at least 9.5 to just throwing in the whole 10 quarts off the shot and doing a one and done heat cycle to drop out the excess to get to the proper level. I don't recall exactly now what I measured that came out but was less than I put back in, I knew I spilled some on the garage floor but the main part was that I was thrilled in the discovery I did not have to touch my exhaust to flex it down. The gasket manipulating is a pain of course to create that clearance to take the pan out and put back in but its all very doable if one is careful and not forcing the gasket to flex too much. From the quote I got at a transmission shop of 900.00 here in Canada ( never asked at the dealer what they charge ) I saved 700.00 doing it myself after paying for the supplies so that to me paid very good wages !, and I knew what fluid was put in and that I had changed the filter and that the level is correct without any doubts. 
    • bojanglespa
      2016 Sierra 1500 6.2L lifter Failure 🤨

      By bojanglespa · Posted

      I do have one of the AFM diasable box, using it for last 1.5 years.
    • Mellowth
      Tonneau cover and rack combo

      By Mellowth · Posted

      I found a setup that lets me open the cover partway with racks installed, using side-rail-mounted systems for easy access.
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Typically its said and I agree so far that the engine oil drain plug oring is not required to be changed out unless you see some damage happening to the oring as apparently the oring lasts well. The dealer I have been getting a few parts from never even stocked the oring but instead stocked the whole drain plug that comes with a new oring which for the dealer is easier because they just throw in a new drain plug if there was any question about damage on it as well and charge the customer accordingly but again only if it is needed.    Also a hint about the drain plug oring to help it last vs a risk of causing damage to it, after its been removed and wiped off or washed off ( that is a whole other topic about some solvents damaging orings because some solvent types do ) to make sure to relube the oring with a bit of new oil so that it won't "grip" on the sealing surface of the pan and needlessly stress out the oring. Its no different than putting some oil on the sealing ring of the engine oil filter. So I just grabbed a new drain plug to have on hand although more recently bought just the oring as well but as its special it costs half the price of the drain plug ... !   Since you mentioned the hate to be empty handed theme, I am not sure what you have in the way of filter removal tools as I like using the exact sized for the filter steel 1" wide band with side to side swivel handle filter removal tool, and it can be used to snug up the filter without risk of damaging a filter as well ( its probably a lisle brand I have ). The drain plug hex size is 15mm and I always like using a 6 point socket if I have a choice and with this truck I've been using just a 3/8 ratchet that has a fairly long handle. Do you have a funnel that will work to pour oil in as that is definitely the short coming bastard part about the design with that fill port on the valve cover on such an angle that no normal funnel will even work. There are adapters and things on the market that will set into or screw into that fill port, I didn't want to deal with US shipping as that is all I was seeing at the time so caved and bought a Lisle brand multi vehicle fit adapter funnel kit and it really works well but there are much less expensive adapters out there that work in conjunction with an off the shelf funnel that would do the job also. Now that I have it, I like how it works and works so slick with the shape of the Amsoil 1 quart containers I have now switched over to. Whatever you do, have a funnel system of some sort as you will be swearing if you dropped the oil and then realize you have nothing to properly pour new oil in without spilling it all over the engine !.     Other comments, quite a bit of oil flows out down the filter when its cracked loose due to the housing above the filter so let it dribble down the filter until it slacks off flow and then remove the filter to create less possible mess. It seems these engines can sit for quite a while and drip and if you have time let it sit there and drip out of the engine as much as it wants. Also a good time to grease the 9 zerks on the front end, that's my typical practice anyway to grease the suspension and steering each time I change the oil. And remember to reset the oil change minder ( not something I am used to doing with older vehicles and equipment ). 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...