Jump to content

Snow tires

rjgvt

By rjgvt
in 2020-2026 Silverado HD & Sierra HD

 Share

Recommended Posts

rjgvt Enthusiast

rjgvt

Posted
Posted (edited)

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm.

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

Edited by rjgvt
  • Like 1
rdonarski Enthusiast

rdonarski

Posted
Posted

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the all-terrain tire option, and they seem to be doing just fine in the snow. 

rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

rdonarski Enthusiast

rdonarski

Posted
Posted
2 hours ago, rjgvt said:

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

As it would turn out, I checked this morning, and my closest Harbor Freight (50 miles away) doesn't stock them. Said I could go to the store, order it and have it shipped to the store for free (2 trips to store). Checked on shipping it - $6.99 - oh hell yes! Wouldn't make one trip for $6.99.

  • Like 1
Ejl923 Enthusiast

Ejl923

Posted
Posted

Been using the HF dolly for years.  Hurt my back 20 yrs ago and this allows me to lift/rotate tires.  The fact that the tire can be spun to line up lugs is the best thing.

  • Like 2
Johnsondavid New Member

Johnsondavid

Posted
Posted (edited)
On 9/12/2024 at 7:31 AM, rjgvt said:

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm. Geometry Dash Scratch

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

I like your idea. Replacing new wheels will help the car operate better and above all it provides safety when moving.

Edited by Johnsondavid
revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
On 9/12/2024 at 7:38 AM, rdonarski said:

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the [b]all-terrain tire option[/b], and they seem to be doing just fine in the snow. 

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Edited by revrnd
  • 2 weeks later...
revrnd Senior Enthusiast

revrnd

Posted
Posted

This comment came to mind yesterday after reading the good & bad comments about Michelin's quality in the other ongoing tire thread in the Silverado HD section.

 

My brother had 2 sets of Michelin LTX M+S tires on his 2016 2500 Sierra HD. He was happy w/ the tire wear on the 1st set, however the 2nd set wore out faster than expected. 

 

His set up and/or usage hadn't changed. Talking to the tire shop, they said that they had seen the less than satisfactory tire wear from Michelin tires.

rdonarski Enthusiast

rdonarski

Posted
Posted
On 9/19/2024 at 9:35 PM, revrnd said:

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Thought I responded to this, but don't see it. Yes, they are the Transforce ATs. They have worked fine for me in the winter, but with this being my 'Till death do us part' truck, I try to minimalize winter use.

revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
2 hours ago, Hoginedgewood said:

Will you have to use a tpms relearn tool every spring and fall?

 

 

Yes. This is the relearn tool that I picked up on Amazon. It works fine w/ the GM sensors. 

 

20241006_205615.thumb.jpg.12a1633d74c89c49440e77b0df3dcb7a.jpg

 

My set of winter rims have aftermarket Schrader(?) sensors & the truck wouldn't recognise them. My local garage was able to 'match' 1 of them to my truck using their Snap-On 'tool' so I'm hoping once they do the rest, my tool will work when I do the swap in the fall.

 

I'll try to remember next month to post.

Edited by revrnd
rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

I have used an Autel TS508 to relearn the TPMS sensors on my previous 1500’s. I used it to program the tire placard pressures to 55psi front/rear on my 2024 AT4 HD. Will use it to relearn the sensors when I take off the KO3’s and put on the snow tires/wheels.

  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted

I spent 2 years in the Rockies in a 1975 Ford Ranger 2WD....it had studded tires on the rear and I stuck 2 manhole lids in the bed....I was actually quite surprised how well the truck did in the snow and ice.....I remember trying to beat the snowplow going up highway 285 on way home at 5 in the morning.......2-4in of dry colorado powder is like driving on asphalt compared to the plow scraping down to the ice.....studded tires are awesome

revrnd Senior Enthusiast

revrnd

Posted
Posted

Studded tires are fine where they're legal.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • davester
      Bench seat swap for 2021-2024 suburban

      By davester · Posted

      probably won't get a response from that user, as they haven't returned to the site since making that one post.  users don't (at least I don't, and I haven't seen any setting which would notify me via say, email) get any notification other than going to this site, and checking if they got a response on their thread...
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Thanks - I wasn't quite caffeinated this morning. 2:1 makes sense, turning the crankshaft 360 degrees will turn the cam 180 degrees, and had I done that, the cam's dot would be at 6 and the crank's at 12 again.   I went ahead and took the sprocket off anyway, aligned everything dot-to-dot including the balance shaft just for s&g. I'm glad I did because I discovered no Loctite on the timing sprocket bolts. Maybe it's not required, but at only 20 ft-lb torque spec, those bolts aren't in there very tight. Cleaned and reassembled with some thread locker and torqued.   A general observation: Less is more with RTV. If a little doesn't stop a leak, a LOT probably won't, either. RTV is thinly veiled revenge, in a tube...      
    • richard wysong
      Wow I'm in a pickle. (Broke down truck) and a story.

      By richard wysong · Posted

      The timing marks are ok, that is #1, you can turn it over until they line up and it won't change anything, the crankshaft turns twice for every camshaft revolution, I have always set up SB Chevs as your pic shows using a straight edge
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      Someone's been here before.... There is a receipt for a 3-piece timing set, purchased earlier this year.   Is this picture something, or, nothing?   I have the timing cover off and my crank is perfectly TDC and the keyed gear's locating mark is dead on 12 o'clock.   The cam gear locating mark is also at 12 o'clock. Now, I'm not an expert, but all the install guides say the two locating marks should meet and be perfectly aligned when installing a timing set. The mark on the crank should be dead on 12:00 and the cam gear's mark should be dead on 6:00, and both marks should be perfectly vertically aligned.   I believe the timing gear is keyed or has a dowel that ensures it can only be installed on the cam in one position, so I have to believe the cam is out of phase somehow. At the very least, with a triangular bolt pattern, it can only be installed in one of 3 different positions.   Before I pulled the front cover, the truck was running alright, no service engine soon lights except an occasional P0172 / rich condition. Timing -16 timing at idle (should be +16), and total -35% fuel trim, two conditions I haven't been able to figure out.   In related news, my injector tested pretty well, wasn't leaking, but I had it rebuilt anyway, and it's on it's way back to me.         Along with this discovery, the good and bad:   Good: The oil pan seal appears undamaged.   Bad: -The timing cover has been reused, and the positioning dowels have been broken. That could explain some of the leaking. -Some kind of white paste or grease was used to try to seal the oil pan seal and timing cover (since wiped off..). -Then, someone globbed silicone all over the front of the cover and also buried the ckp sensor in it. But, they didn't put any inside the cover or use RTV to try to seal the oil pan seal with the timing cover (good).
    • Grumpy Bear
      PF63 Oil Filters Going Away?

      By Grumpy Bear · Posted

      The guy that owns K&P filters last I checked in with him has over 300,000 miles on his Dodge base Hemi using his own 35 micron absolute stainless mesh filter from its first oil change.    The GM study I've posted a dozen times shows the relationship in engine life based in multiples of base units, not miles or years. That is the base unit is the number of miles the motor ran using the reference filter efficiency.    The above two paragraphs dismantle anecdotal arguments IF one changes oil often enough to prevent particle formation and the motor is in otherwise good shape. That is not full of silica (no air filter) or suffering a metallurgical issue that is not part of the lubrication discussion. Poor heat treat in example.   Data from UOA's I've reviewed from more than a few engines can show remarkably broad variations in oil cleanliness using the exact same filter over the course of an engines life.     Lastly there is the common sense of it. Wear debris WILL circulate the engine BEFORE it ever sees a filter in route to that filter and WILL harm the pump which NEVER sees filtered oil.    Alpha question then becomes, given the facts, how long do you believe is a reasonable service life from a vehicle you are certain you will not pass down? That is the junk yard will be it's resting place when you're done with it? (the moral issue most don't care about).    Omega question is then how diligent are you prepared to be in general mechanical, air & oil maintenance? Preventing particulates and keeping them sufficiently dilute; preventing the precursors from generation, amalgamation and precipitation.    If I get a good look at the engine bay of a vehicle I have a fair idea of the owners commitment to the inside of the power train. That 30 micron WIX is still more efficient than a sieve.                 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...