Jump to content

Snow tires

rjgvt

By rjgvt
in 2020-2026 Silverado HD & Sierra HD

 Share

Recommended Posts

rjgvt Enthusiast

rjgvt

Posted
Posted (edited)

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm.

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

Edited by rjgvt
  • Like 1
rdonarski Enthusiast

rdonarski

Posted
Posted

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the all-terrain tire option, and they seem to be doing just fine in the snow. 

rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

rdonarski Enthusiast

rdonarski

Posted
Posted
2 hours ago, rjgvt said:

Harbor Freight has sales often. The dolly is nice as it is mechanical and no hydraulic cylinder. 

 

I don't think I stated in my first post that I had a set of the non-studded Hakkapeliitta LT3's on my last 1500. I had to travel out of state 3 hours away every week for the last 8 months of my work life that went into winter. My last commute was in a freezing rain/snow storm. My truck was coated in ice. I drove on the thruway in NY at 45mph with the flashers on. I made it to work with no issues. 

 

If you need snow tires and can afford the $$ for Nokian snow tires, I think they are some of the best. After getting stuck in the boonies with AT tires several years ago, its dedicated snow tires for me. The guys that helped get me turned around to get out all had studded snow tires. 

 

 

As it would turn out, I checked this morning, and my closest Harbor Freight (50 miles away) doesn't stock them. Said I could go to the store, order it and have it shipped to the store for free (2 trips to store). Checked on shipping it - $6.99 - oh hell yes! Wouldn't make one trip for $6.99.

  • Like 1
Ejl923 Enthusiast

Ejl923

Posted
Posted

Been using the HF dolly for years.  Hurt my back 20 yrs ago and this allows me to lift/rotate tires.  The fact that the tire can be spun to line up lugs is the best thing.

  • Like 2
Johnsondavid New Member

Johnsondavid

Posted
Posted (edited)
On 9/12/2024 at 7:31 AM, rjgvt said:

I started my quest to get winter wheels for my truck soon after I got it this past January. I like to have a spare set of wheels/snow tires so I can change them over in October and April. I had a set for my 1500's but sold them as they were 17", same size as the spare.

 

I found a set at an offroad shop in April and bought them. They look like Denali wheels that the shop sent out to be powder coated and are the same size as my OEM wheels, 20 x 8.5 with the stock offset, 47mm. Geometry Dash Scratch

 

Went to my local tire shop to order non-studded Hakkapeliitta LT3 tires in LT275/65/R20 sometime in July. There were 3 in the country that were available. Tire shop got them and stored them for me until a 4th one came in. I called the US Nokian phone number and a guy that lives in my town in VT answered which was odd. He didn't think any would show up until October due to the Russian plant being shut down for obvious reasons. Called him again last week and still none. I asked about the studded version and there were 77 available in my size at the local Nokian warehouse. He told me that they run Nokian studded tires on all of there cars/truck. Went to the tire shop and changed the order for the studded version.

 

Got them put on today along with the GM TPMS sensors I got from my GMC dealer. Also picked up a wheel dolly from Harbor Freight last week when it was $25 off. Plan is to use it to lift the wheels/tires to install when changing over twice a year. They are made to lift a vehicle with 4 of them to move a vehicle in a garage.

 

Removed a front wheel today and installed one of the new wheel/tire combos with the HF dolly and it worked out well. Put the original wheel/tire on with the dolly. It beats lifting a wheel/tire to get it on considering that I'm not getting any younger or stronger. 

 

 

Snow tires.jpg

Wheel dolly.jpg

I like your idea. Replacing new wheels will help the car operate better and above all it provides safety when moving.

Edited by Johnsondavid
revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
On 9/12/2024 at 7:38 AM, rdonarski said:

I like the thought of the wheel dolly. I was just by Harbor Freight on Tuesday. Wish I'd known about it then. I'm at the age too where tires are not getting lighter and I rotate my own. I live in N WI, so am very familiar with snow. I had a 2-wheel drive car that couldn't make it up my driveway with 2 inches of snow with all-season tires (misnomer). I bought an extra set of tires/wheels for that. Problem was storage plus when I got rid of the vehicle the new owner didn't want them, so I had to get rid of them. I replaced the car with a SUV. 1st snow I went right into the ditch with the all-season tires that came on that. Put snow tires on it immediately. Looked at my options. Another set of wheels and tires, another set of tires to swap on rims twice a year and running snow tires year around. Due to storage logistics and convenience, I went to running snow tires year around. Probably a little rougher ride and I only get half the miles on them that I get on regular tires, but it works for me. My truck came with the [b]all-terrain tire option[/b], and they seem to be doing just fine in the snow. 

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Edited by revrnd
  • 2 weeks later...
revrnd Senior Enthusiast

revrnd

Posted
Posted

This comment came to mind yesterday after reading the good & bad comments about Michelin's quality in the other ongoing tire thread in the Silverado HD section.

 

My brother had 2 sets of Michelin LTX M+S tires on his 2016 2500 Sierra HD. He was happy w/ the tire wear on the 1st set, however the 2nd set wore out faster than expected. 

 

His set up and/or usage hadn't changed. Talking to the tire shop, they said that they had seen the less than satisfactory tire wear from Michelin tires.

rdonarski Enthusiast

rdonarski

Posted
Posted
On 9/19/2024 at 9:35 PM, revrnd said:

 

Are they they the Firestone Transforce ATs? I've used them as the winter tire (to save the alloys from winter here in Ontario on my 2017 2500HD). I haven't been impressed w/ them since day 1. I see my 2024 is coming w/ them 🙄 & will eventually just wear them out on the alloy wheels. I still have the steel rims from my 2017, so I'll get some proper winter tires in the future.

 

 

Thought I responded to this, but don't see it. Yes, they are the Transforce ATs. They have worked fine for me in the winter, but with this being my 'Till death do us part' truck, I try to minimalize winter use.

revrnd Senior Enthusiast

revrnd

Posted
Posted (edited)
2 hours ago, Hoginedgewood said:

Will you have to use a tpms relearn tool every spring and fall?

 

 

Yes. This is the relearn tool that I picked up on Amazon. It works fine w/ the GM sensors. 

 

20241006_205615.thumb.jpg.12a1633d74c89c49440e77b0df3dcb7a.jpg

 

My set of winter rims have aftermarket Schrader(?) sensors & the truck wouldn't recognise them. My local garage was able to 'match' 1 of them to my truck using their Snap-On 'tool' so I'm hoping once they do the rest, my tool will work when I do the swap in the fall.

 

I'll try to remember next month to post.

Edited by revrnd
rjgvt Enthusiast

rjgvt

Posted
  • Author
Posted

I have used an Autel TS508 to relearn the TPMS sensors on my previous 1500’s. I used it to program the tire placard pressures to 55psi front/rear on my 2024 AT4 HD. Will use it to relearn the sensors when I take off the KO3’s and put on the snow tires/wheels.

  • Like 1
Dunn Senior Enthusiast

Dunn

Posted
Posted

I spent 2 years in the Rockies in a 1975 Ford Ranger 2WD....it had studded tires on the rear and I stuck 2 manhole lids in the bed....I was actually quite surprised how well the truck did in the snow and ice.....I remember trying to beat the snowplow going up highway 285 on way home at 5 in the morning.......2-4in of dry colorado powder is like driving on asphalt compared to the plow scraping down to the ice.....studded tires are awesome

revrnd Senior Enthusiast

revrnd

Posted
Posted

Studded tires are fine where they're legal.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,897
    Total Members
    8,960
    Most Online
    ncleg
    Newest Member
    ncleg
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,271 Guests (See full list)

  • Latest Articles

  • Posts

    • dna9656
      New to Me 2010 SLE (Quirks, Issues)

      By dna9656 · Posted

      Your tire pressure issue may just be batteries, you can reset them using tge Ing switch (I think) and the owner's  manual. ChatGTP will b e a faster, better help than Google.
    • Another JR
      Towing In Loose Gravel

      By Another JR · Posted

      The thinking is that starting out in a higher gear makes it easier to avoid applying excessive torque when pressing the gas pedal. In a modern 4wd truck with 4 low and a limited slip or locking rear end, I would use 4 low and try to crawl up the ramp. Sometimes if they are too slippery, you have to back up to let the boat have some bouyancy, and then accelerate briskly to get some momentum to help you pull the through the slippery parts. 
    • XY74
      Roll up bed cover experiences

      By XY74 · Posted

      I have a Retrax pro that I first had on my 2020 chevy and transferred it to my current GMC.  It stays in the garage most of the time, so hard for me to judge it's long term weather resistance.  It still works perfectly, been very durable.  It doesn't see oil patch usage, but it's not a mall queen.  It keeps most things mostly dry (small leaks) and the security of it is enough to slow someone down but not keep them out for long.  I would buy one again, it works for me.     
    • fm2176
      New to Me 2010 SLE (Quirks, Issues)

      By fm2176 · Posted

      Thanks to the convenience of Amazon, I was able to get a few things done to the truck today.  I installed Carquest Premium oil and air filters with five quarts of Mobil1 High Mileage 10-30 along with a quart of Pennzoil Platinum 5w-30 I already had.  The latch for the flip up center console lid was broken so I replaced it along with the power mirror switch.  I found my push retainer assortment this morning and reattached the plastic under the bumper and it was only held on with a few screws and retainers.  Then I programmed a new remote keyless entry fob so I can lock my dog in the truck when I take her out with me (I've got to keep the air going for her since it's been in the 100s).  Finally, I ordered some LED interior bulbs and replaced the reading lamps.  The front lights are working fine while one of the back lights only works intermittently and the other not at all.   While under the truck, I found the source of at least one of the noises: the sway bar links need replacing.  I ordered a set of Suspension Dudes links with Code Red bushings.  Never heard of them, but they're made in the USA and have decent reviews.  While making yet another Amazon order, I went ahead and added a set of front tow hooks.  I went with red, since that's the color of the sway bar link and bushings and it should look decent enough on a black and chrome truck.  Speaking of which, it doesn't bug me much, but the passenger side mirror has a chrome cap while the driver side doesn't, so eventually I'll make them match one way or another.  Oh, and I ordered a $20 TPMS reset tool.  No idea if it will do anything for my sensors but it was cheap and will work for the Ford Transit Connect as well.     For tradition's sake, I ordered a new oil change wrench.  I kept the Snap-On 9/16"x15mm GM wrench I bought when I was 18 in the 2006 GMC from the time I bought that truck until the truck was lost.  While I was tempted, there's no need to spend $80 for a new SO wrench, or even $50 with shipping for a used one on Ebay.  I just bought a Duratech 15mm extra-long ratcheting wrench to do the job as needed.  It works, and if I like that wrench enough, I'll buy the set.  
    • Another JR
      Multigate electrical problem

      By Another JR · Posted

      The recall is for exactly this issue - those drain holes combined with the limited environmental capability of the tailgate electronics card inside the tailgate were a problem. The “safety issue” was the potential for the tailgate to spontaneously open, but all kinds of tailgate misbehavior can occur from water contamination of that control card.    There is no real fix yet. The initial recall just disabled the tailgate. Later, when parts became available, they would replace bad parts with new parts of the same bad design. My dealer is going nuts because the few times I let them get their hands on my truck, my tailgate is off due to a slide-in camper installation. They really want to cut my tailgate wires, but I won’t give them the chance. I will let them get their dirty hands on it when a real fix (redesign) is available.  My tailgate, which works just fine with sealant plugging the drain holes, will remain safe in a dry storage crate until then.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...