Jump to content

Evap Vent Valve Solenoid #

blueyedevil911

Recommended Posts

ev372 New Member

ev372

Posted
Posted

I have a 2004 Chevy Silverado 1500 that needs the "Vent Valve Solenoid" replaced due to the error code-over filled and jumped on the excelerator-stupid me. I called Advance Auto and the part # 25932571 and 214-2149 do not fit my truck. Auto Zone can order one but, no pics of the part to compare it ot hteold unit. I think mine is the square one when I started checking for possible problems. Anyone replaced this on 2004 Silverado and what did it look like? Is it 1 part or 2 parts with the 5/8" hose connected between them? Any help would be great. Its sitting at the dealership right now- $225. for part and $465 to install. OUCH and double OUCH. I cant afford this right now. So I hope someone can provide some help. So far this thread had been a great source of information that you cant find anywhere else. Thanks from, EV372

  • 2 weeks later...
  • Replies 117
  • Created
  • Last Reply
cf1 Enthusiast

cf1

Posted
Posted
ok, we need to find an evap vent valve. dealership charging us 169.18 for our 2007 silverado 1500 classic ls 4.. what do we do?

 

I have a 2006 silverado 1500. I went to gm and told them i need a solenoid for a 2006 suburban same part, with tax $30.00. put part on (exact same part) light went offf no problems. part # gm# 25932571 delco part # 214-2149. go for it..

B Ditty Enthusiast

B Ditty

Posted
Posted

I have this same code coming up on my 2003 ext cab, short box. I have been reading like crazy on here but everything mentioned seems to be for 2004 and up. Will this 214-2149 work on my truck? From what I can tell, my unit is located on the driver side, top of the tank on the frame rail. Near the gap between the cab and the box. Dealership wants about $450.00 bucks and I want to do this myself. Just want to make sure I get the right parts!! Any help will be GREATLY appreciated. Thanks.

jrrod2004 Senior Enthusiast

jrrod2004

Posted
Posted
ok, we need to find an evap vent valve. dealership charging us 169.18 for our 2007 silverado 1500 classic ls 4.. what do we do?

 

I have a 2006 silverado 1500. I went to gm and told them i need a solenoid for a 2006 suburban same part, with tax $30.00. put part on (exact same part) light went offf no problems. part # gm# 25932571 delco part # 214-2149. go for it..

 

 

 

was that the relocated version or just the swap???

cf1 Enthusiast

cf1

Posted
Posted
I have this same code coming up on my 2003 ext cab, short box. I have been reading like crazy on here but everything mentioned seems to be for 2004 and up. Will this 214-2149 work on my truck? From what I can tell, my unit is located on the driver side, top of the tank on the frame rail. Near the gap between the cab and the box. Dealership wants about $450.00 bucks and I want to do this myself. Just want to make sure I get the right parts!! Any help will be GREATLY appreciated. Thanks.

 

you can replace it with a screw driver. its round with a electrical connection and a hose. the hose was good so i reused it. had to buy a hose clamp. just call a gm dealer and ask for a evap solenoid for a suburban 2003 . i heard some are square. gm want you to buy a kit and reroute it for $184,00. witch is bull just get the solenoid and put it on..

cf1 Enthusiast

cf1

Posted
Posted
ok, we need to find an evap vent valve. dealership charging us 169.18 for our 2007 silverado 1500 classic ls 4.. what do we do?

 

I have a 2006 silverado 1500. I went to gm and told them i need a solenoid for a 2006 suburban same part, with tax $30.00. put part on (exact same part) light went offf no problems. part # gm# 25932571 delco part # 214-2149. go for it..

 

 

 

was that the relocated version or just the swap???

 

 

just the swap . gm want you to buy a kit and re route it up over the transmission.. $184.00

jrrod2004 Senior Enthusiast

jrrod2004

Posted
Posted

Gotcha, I did mine for just under 100 bones. Rerouting kit and went to get some 5/8 heater hose and installed it myself...

a10secstreetcar New Member

a10secstreetcar

Posted
Posted

My uncle has an 2007 Silverado with the same code. ( PO0449 )

 

GM part # 2593271 is this the same part for my uncles truck?

 

If so than I would be lead to believe I could just buy the Acdelco part # 214-2149 for cheaper and replace it with the bad EVAP solenoid.

 

Correct?

 

Please confirm this is the same for my uncles '07. I talked to GM on Friday the parts guy wasnt any help. I think he knew what I was trying to do. lol ( Save money )

 

Thanks in advance!

 

Kyle

jrrod2004 Senior Enthusiast

jrrod2004

Posted
Posted
My uncle has an 2007 Silverado with the same code. ( PO0449 )

 

GM part # 2593271 is this the same part for my uncles truck?

 

If so than I would be lead to believe I could just buy the Acdelco part # 214-2149 for cheaper and replace it with the bad EVAP solenoid.

 

Correct?

 

Please confirm this is the same for my uncles '07. I talked to GM on Friday the parts guy wasnt any help. I think he knew what I was trying to do. lol ( Save money )

 

Thanks in advance!

 

Kyle

 

 

This is from Rich (MS3DALE), parts guy from a GM dealership:

GMT800 Silverado Part Numbers:

 

OEM gas cap - 25827335

OEM EVAP canister vent valve - 19207763 (This is actually a kit that gives you both pieces you mentioned,the round one and the square one)

OEM EVAP canister - 15137021

OEM canister purge solenoid vent valve - 12581282 (This is the one that sits on top of the intake manifold)

 

Your part number of 214-2149 should work if you are looking for the EVAP Solenoid only

cf1 Enthusiast

cf1

Posted
Posted
My uncle has an 2007 Silverado with the same code. ( PO0449 )

 

GM part # 2593271 is this the same part for my uncles truck?

 

If so than I would be lead to believe I could just buy the Acdelco part # 214-2149 for cheaper and replace it with the bad EVAP solenoid.

 

Correct?

 

Please confirm this is the same for my uncles '07. I talked to GM on Friday the parts guy wasnt any help. I think he knew what I was trying to do. lol ( Save money )

 

Thanks in advance!

 

Kyle

 

that the part 214-2149 .. dont let gm con you and say you need the rerouting kit. all you need is the evap solenoid.. youl need a screw driver and no other tools.

B Ditty Enthusiast

B Ditty

Posted
Posted
I have this same code coming up on my 2003 ext cab, short box. I have been reading like crazy on here but everything mentioned seems to be for 2004 and up. Will this 214-2149 work on my truck? From what I can tell, my unit is located on the driver side, top of the tank on the frame rail. Near the gap between the cab and the box. Dealership wants about $450.00 bucks and I want to do this myself. Just want to make sure I get the right parts!! Any help will be GREATLY appreciated. Thanks.

 

you can replace it with a screw driver. its round with a electrical connection and a hose. the hose was good so i reused it. had to buy a hose clamp. just call a gm dealer and ask for a evap solenoid for a suburban 2003 . i heard some are square. gm want you to buy a kit and reroute it for $184,00. witch is bull just get the solenoid and put it on..

 

 

Thanks for the reply. I have one more question for you guys.....I thought I located this thing, but now I am not so sure. Does anyone have a image or diagram for a 2003 Silverado? Or can anyone explain to me where I should be finding this thing? I thought it was above the frame rail between the bed and the cab, but after crawling under there i don't see any electrical connection running to the unit, only one hose the routes over the fuel tank and back to the charcoal cansiter. Thanks.

Bob D Enthusiast

Bob D

Posted
Posted
...can anyone explain to me where I should be finding this thing? I thought it was above the frame rail between the bed and the cab,...

That's where it is. Trace the hose (5/8" or so) from the Evap Canister to the Vent Valve.

B Ditty Enthusiast

B Ditty

Posted
Posted
...can anyone explain to me where I should be finding this thing? I thought it was above the frame rail between the bed and the cab,...

That's where it is. Trace the hose (5/8" or so) from the Evap Canister to the Vent Valve.

 

 

Ok. Thank you very much. Have you had any experience with this? I am just wondeing how I am gonna get it out and more importantly, what is the proper part number. I keep seeing this AC part # 214-2149, but it looks round. The one on my truck looks square and it doesn't look like that round one will fit up there. Any info or tricks? Thanks again.

Bob D Enthusiast

Bob D

Posted
Posted
...just wondeing how I am gonna get it out and more importantly, what is the proper part number. I keep seeing this AC part # 214-2149, but it looks round. The one on my truck looks square and it doesn't look like that round one will fit up there...
Took mine out of the '03 to diagnose / bench test it (suggest you do the same unless you're getting a specific code indicating Vent failure(mine bench tested OK)).

It's affixed with a "clip" type thing to a bracket which is not obvious looking at it. I ended up disconnecting hose, elec. connection, unbolting, and wrestling it out as an assy. (had to turn it every which way to extricate it). Once out, I could see and disconnect the "clip", removing it from the bracket, which made re-install easy. It's pretty straightforward. Hose connection fitting was the most troublesome for me.

Note: Your replacement should look the same. I noticed RockAuto has some erroneous depictions of the Vent Valve that shows a picture of the Purge Valve.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • mysery1
      What have you done to your K2 today?

      By mysery1 · Posted

      I have a 2018 Silverado Custom with 156k on the odometer. In the last month I've replaced the plugs, wires and the driver side engine mount. My wife just returned from a trip of about 1500 miles and told me the brakes are making a grinding noise when applied. I drove it and looked it over and this is what I found with the driver's side rear rotor.   I'm going to order new pads and check about having the rotor resurfaced. Hopefully this is easier than the last 2 jobs.   Peace  
    • FiLo
      5.3 / 6.2 valve covers / oil burning

      By FiLo · Posted

      Any update if the new valve cover help with the oil consumption?  I have a 2014 GMC sierra and my truck is consuming a lot of oil so I’m wondering if replacing the driver side valve cover will stop some of the oil consumption. Thanks 
    • Deadwood
      primary drive belt tensioner

      By Deadwood · Posted

      I bought belts and pulleys for my '20 L5P at Rock Auto a couple years ago. I have used them for many years, and almost always save significant money, especially when I buy maintenance stuff ahead of time.   They carry many OEM parts, which is all I use unless an aftermarket is shown to be same/superior, or if it is an insignificant part or unavailable OEM part anywhere else. RA is usually lower priced, often by a bunch, but parts are sometimes unavailable or out of stock, and I do shop around and sometimes find better prices at other sites.   Be aware that you pay shipping, and if you buy multiple items and they are coming from different warehouses, the shipping can kill the advantage. Planning ahead is best if possible.   If you have a transmission service in the near future, check out their OEM (AC Delco ULV) fluid, usually MUCH less than anywhere else.
    • Deadwood
      10L1000 anyone with High Mileage ? I hate Damocles....

      By Deadwood · Posted

      New member here, very long time occasional guest. Saw this thread, thought it would be a good time to contribute someting. It is only my experience and not a claim that everyone will have the same.   I bought my '20 3500 L5P new and have put 99.9% (literally) of it's current ~400k miles on it myself, with over 50% of that towing loads between 4k to 15k, and to me this truck has been nothing short of amazing. For the first 235k I had zero issues, and from there until 321k I replaced a NOx sensor, two failing glow plugs, and three of the notorious injector connectors. I believe this truck is in part, a testament to good luck, but also good care and following a decent maintenance schedule (I also keep meticulous records.) As a result, it looks as good as a well cared for 70k rig, up and down, inside and out.   At some point before that 321k mile mark I began to get a little spooked about the 10L1000, especially the valve body. Word of mouth about potential issues prompted me to jump on the net to sift through all the noise and determine what all the fuss was about. I routinely take long trips, coast-to-coast and points in between, so roadside breakdowns can be '...a thousand miles from nowhere' and a bit of a challenge, and though I had no issues, my guard was up and activated.   And then I stumbled across a chance to salvage some parts off a new 2025 that had been wrecked in transport. I grabbed a few wear items (alternator, pulleys, etc.) and on a whim asked what the ten speeder would cost me. It was cheap...really cheap. I knew some changes had been made in the '24+ version 10L and were supposedly not compatible, but I called service/parts at my local Chevy dealer and asked why and they didn't know. A call to a well known aftermarket transmission outfit revealed it was very likely it would be fine, but to them not 100% sure.   Because it was cheap (really cheap) and I was spooked, I took the chance. Had it installed by a local shop and it worked like a champ, shifted just like the original. At it's first service at 37k, I had the shop put in a Next Gen valve body kit, which after some initial hiccups and rough shifts, smoothed out though with somewhat firmer shifting.   All that said, I have a very serious concern about my newer transmission as just two weeks ago it suddenly began to exhibit a strong reluctance to engage forward or reverse. It was a bit past due anyway so I took it in for service. The reason it was sticking was due to 'glitter' in the fluid clogging the filter...not good folks, often indicates a converter giving out. We ended up going ahead with the new filter and fluid, first to see if it would move and shift, and then if so buy me a little time. It did, and I've driven it over a thousand miles and it is shifting smooth, no noises or slipping. Regardless, it looks like a third gearbox is in my future so I can resume taking long trips with some confidence. In the very short term, my curiosity will have me examining the fluid to check how much glitter has reappeared.   An earlier poster had alleged, in the context of 10L100 failures, that it is another example of how we seasoned citizens somehow descend into hysteria, lose control of our senses, and react irrationally after brief encounters with the idiocy of the internet infosphere. Let me say (and I have used and abused said internet since it's infancy) there is no segment of the populace that has a corner on over-reaction to digital garbage. Just as my offering of experience in this arena is purely anecdotal and should not be considered gospel or all-encompassing, I believe it is still worthwhile information to consider, along with other relevant anecdotal experiences about things like complex transmissions, especially when balanced with other sources.   So to answer the original question, yes I got high miles out of my first 10L, trouble free for 321,000. Now I really wonder how much longer it would have went. Did I 'overreact' to the internet ghouls by replacing a 'good' one with a 'bad' one? Maybe. Who knows, the thing might have taken a puke a 100 miles later. So I'll just fix it again, then move on and start thinking about all the other stuff that will eventually wear out. It still has the original brakes (they're at ~60%), original injectors/pump, turbo, water pump, etc....pretty much original everything. Knock on wood.
    • swathdiver
      6 Speed vs 8 Speed

      By swathdiver · Posted

      At peak temperature.  They get to cool down and warm up more, especially those with the external cooler.  I have three GMT900s and one of them has over 225K on its original transmission.  Fluid gets changed about every 36K miles, all of it.     It's not the bean counters, it was the government.  They had to meet CAFE standards and other government requirements.   To get around that, we tune them and modify them to our liking.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...