Jump to content

Tpms Reset

ricci151
 Share

Recommended Posts

Thurman Enthusiast

Thurman

Posted
Posted

FWIW: I have an '07 GMC. I have a friend who owns a brake/alignment shop. He states that some of the '07 GM trucks are hard to reset even with his $300+ tool. I had tried mine multiple times and not gotten it to work. He tried it a few times and could not get it to work. He sends them to the local Chev dealer who resets them with better equipment and charges GM, regardless of Chevy or GMC. So--it may be the sensors they used for some period of time. David

TRCM Enthusiast

TRCM

Posted
Posted

How accurate are these sensors ?

 

I reset mine to read the correct corner of the truck, and I also adjusted the tire pressures to 36 psi in all 4 tires. The TPMS confirmed the 36 psi.

 

Then while driving the next day, I checked it to see how much they had heated up, and got 4 different readings, ranging from 34 psi to 40 psi.

 

Just wondering if they are accurate, or just close.

Ironman24 Enthusiast

Ironman24

Posted
Posted (edited)

I tried for 4 hours over the weekend to reset my TPMS on my 2007 and could not get past the second tire. I think out of all of the times I tried I only got the driver side tire to honk 3 or 4 times. When I did I would move on to the pass. side tire and could never get a honk. I tried everything... letting air out slow then tried letting it out fast then tried filling up with air and never got it to work.

So I did some searching and found this tool on tirerack.com

http://www.tirerack.com/accessories/detail.jsp?ID=111

I got it today and took it out of the box and within 2 minutes had the TPMS reset. I guess I could have gone to the dealer to do it. But I just didn't want to have to go to the dealer every time I rotate my tires. So I think this little thing is worth the money to me. :dunno:

Edited by Ironman24
brims Senior Enthusiast

brims

Posted
Posted (edited)
If you're having trouble getting it to work try running a large magnet across the sensor as you're letting air out. I do this on the Vette and don't even need to let any air out but I do on the truck. I have a friend's truck where I can just use the magnet, so I'm guessing there are differences in the TPMS that's making it easier for some than others... I got a big magnet from Harbor Freight for ~$5 that works great. An old speaker magnet would work well too.

 

Magnet works for the older Corvettes, my TPMS tool came with a magnet for the older Corvettes. Using the magnet on your truck is probably just a placebo affect. Have no explaination for your friends truck.

 

I could never get mine to work and after A LOT of searching I found a service bulletin for certain types of valve stem type (rubber I think it was) letting air out causes a harmonic vibration so the sensor thinks it rolling instead of sending position information and that the programming tool was the only was to get them to register.

 

Wonderful design. Oh well, the OTC 3833 is a nice tool.

 

I tried for 4 hours over the weekend to reset my TPMS on my 2007 and could not get past the second tire. I think out of all of the times I tried I only got the driver side tire to honk 3 or 4 times. When I did I would move on to the pass. side tire and could never get a honk. I tried everything... letting air out slow then tried letting it out fast then tried filling up with air and never got it to work.

So I did some searching and found this tool on tirerack.com

http://www.tirerack.com/accessories/detail.jsp?ID=111

I got it today and took it out of the box and within 2 minutes had the TPMS reset. I guess I could have gone to the dealer to do it. But I just didn't want to have to go to the dealer every time I rotate my tires. So I think this little thing is worth the money to me. :thumbs:

 

My dealer was completely oblivious. On my 07, the guy got in the truck, turned it on, hit the button on the dash, the horn honked, he turned it off, and handed me the keys. I said something about how the manual says that's not right. I forget what happened then, I know I was pissed and left. The mechanics at that dealer are completely worthless.

Edited by brims
  • 5 years later...
ModifiedMax Enthusiast

ModifiedMax

Posted
Posted

Yah i tried the method using the DIC button and the prompt to learn wasn't showing up, as soon as i used my keyless entry FOB and pressed the two buttons for 5 seconds with the e-brake on the horn beeped twice and it was easy from there on, just let air out of each tire starting at passenger front and wait for horn good to go. Thanks for the help guys.

  • 1 month later...
kaufmankdk Enthusiast

kaufmankdk

Posted
Posted

Just purchased these "Take-Offs" from a 2015 Chevy Sierra. Tire PSI 55 Cold Load Range "E" and put them on my 2005 Yukon.

Key on O.K.

Park switch 4 times 1 Beep O.K.

Air up and or air down, No O.K.

Tried from 5 sec, 8 sec, 10 sec. to 30 sec then all the way 120 seconds. no luck ?

I did just read about the rubber stems and there could be something to that ?

is this a freebie at the dealer ? or 85.00 service fee ?

 

Thanks, Kurt

  • 4 years later...
Steve Limbert New Member

Steve Limbert

Posted
Posted

Just ridiculous, classic GM thinking..

Should be set all tires to correct pressure, get in car, press a button to tell it to learn pressure. Done. Like on every other car I have ever owned..

Pathetic.

  • Haha 1
  • 10 months later...
Bigsteve New Member

Bigsteve

Posted
Posted

Tryed this . I got up to active learn and driverside marker lit on . Let air out ,tire almost flat. No beep from the horn . Do I need to buy sensor tool

Bigsteve New Member

Bigsteve

Posted
Posted

Trying to reset my tire location after rotating my tires. Pressed lock and unlock horn beeped twice and driverside parking lite came on let our air no beep . Tire was just about flat. Truck is a 2013 gmc sierra

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Try it the other way around and see if it works, lower all the tires to 20psi, start the procedure and fill the tires one by one.

 

I'd just buy the $12 tool on amazon if that don't work.

swathdiver Senior Enthusiast

swathdiver

Posted
Posted
1 hour ago, Bigsteve said:

Trying to reset my tire location after rotating my tires. Pressed lock and unlock horn beeped twice and driverside parking lite came on let our air no beep . Tire was just about flat. Truck is a 2013 gmc sierra

From 2010 on you need the tool to relearn your TPMS locations.  It is optional before that year.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Coastie05
      Casey from the Texas Hill Country

      By Coastie05 · Posted

      Enjoy the new truck, it’s a beauty. I’m glad you’re keeping the OBS, I love those old trucks. 
    • chris21
      Towing In Loose Gravel

      By chris21 · Posted

      With large equipment or deep mud it is more of a use the higher gear to avoid spinning tires, getting stuck because of spinning tires and doing damage to your machine. The idea is if you run out of torque before you spin tires you can still downshift for more torque. If you are just spinning your tires in the lowest available gear you are stuck and things break.   Automatic transmissions, traction control and electronic transfer cases change the calculation a little as you the driver have less control over each piece. 
    • davester
      My First Project and GMC has me stumped

      By davester · Posted

      are there any codes? with lots of rust, perhaps disconnect/clean both sides of the connection/examine cable ends (the wires) for corrosion going into the sheath & replace if necessary/reconnect ALL the power AND ground cables between the battery, engine, frame, cab, fuse box and starter charm.li (website) has a no-start diagnostic procedure you can work through to get it working.
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      Its no wonder you've gravitated to the oil types and brands you have in later years after trying certain brands and one being a specialty oil or at least very hard to come by up here and the other would have been a commonly found oil of the era and the vastly different outcomes as a result to using the vehicles in question the same distance for an OCI . It shows what marketing hype can do without actually having the product to back up the claims and that is no different now with the insane claims that are written on the side of a bottle of oil from some of the off the shelf oils.    What has surprised me and I was already finding this out before I bought my truck with the GDI engine, that this newer fancy technology that seemingly would suggest better fuel economy/emissions with this high pressure spray of fuel is not in reality kind at all to the engine or at least the oils life. Yet they insist on claiming long OCI with this technology just like they did with the port or similar type fuel injection systems when in reality its a step back in oil life to have a GDI system.    I think the mistake your making Grumpy is that your not sending your samples to Blackstone and getting the feel good glowing report that you can run it another 1000 or more miles and then send another sample where they say run it yet another 1000 miles and on and on it goes until your sending in something that looks a lot like road tar and then they may suggest you change your oil within the next 1000 miles 😆
    • Chuck FB
      OCI, not when but why?

      By Chuck FB · Posted

      I am guessing that engines of that design back then had a better ability to be abused and survive longer than a new design engine with the long timing chain and the overhead cams and phasers etc. But I would never guess that an engine could go that far and not fail spectacularly or at least die a slow death. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...