Jump to content

How-To: Install Underhood Light.

mc7719

By mc7719
in DIY Guides & Reference Library

Recommended Posts

mc7719 Enthusiast

mc7719

Posted
Posted

Well one little option I missed from my '96 was an underhood light. Well I thought this was ridiculous, since my base-model '96 Chev 4x4 had one and my fully-loaded '08 Sierra didn't. So I looked into it a bit further. After asking the dealer who informed me they no longer supplied the part (for any year) I hit the wreckers. I couldn't find an intact one from them either. The common denominator is that they contain MERCURY inside switch built within the light socket unit... and these days... you're not going to find mercury readily available. Hence, GM no longer supplies this "environmentally unfriendly" device (at least that's what they all told me) and the wreckers said they are required to remove the mercury switch portion BEFORE the vehicle goes to the yard, to ensure they are disposed of properly.

 

So I turned to eBay, and 5 days later had a brand new unit in my mailbox:

 

001.JPG

 

So I installed it on one of the metal 'tabs' that help hold the black material to the underside of the hood.

 

DSCN5011x800.jpg

 

DSCN5007x800.jpg

 

I ground the braided cable to the firewall (even though, with the hood already connected by a ground strap elsewhere, this was redundant) And then bought a 'female' side of the OEM plug to run it through a fuse (10-15A), and then connected it to one of the studs on the under-hood fuse panel (where the power take-off for trailering pkg is)

 

 

Below you can see the new looming tied on top the existing, thicker looming along the firewall. Then routed to the right of the fuse box, between the fender.

 

DSCN5008x800.jpg

 

DSCN5014x800.jpg

 

DSCN5013x800.jpg

 

 

The fuse and extra wire is hidden under the fuse box cover:

 

DSCN5016x800.jpg

 

 

End result (sorry, it was dark and the exposure made the picture blurry, but you get the idea):

 

DSCN5005x800.jpg

 

IMG_0364.jpg

 

When the hood reaches the halfway point between fully open, and closed, the light turns off as the mercury inside the socket moves off the contacts :(

pwall Senior Enthusiast

pwall

Posted
Posted

Great job.

I do miss the underhood light...they are convenient.

mc7719 Enthusiast

mc7719

Posted
  • Author
Posted
Great post I'm ordering one now! :)

 

What gauge wire did you use? And the white connector thing in the fuse box? That is the inline fuse you used?

 

EDIT: Sadly I could not find one that isn't from the 1960's eras cars....

FOUND IT: http://cgi.ebay.ca/NEW-OEM-HOOD-LAMP-LIGHT...=item1e60a3c7e3

 

I used the same wire as what was on the harness the light came with, I think 18ga. And yes the white tube is the fuse. Just an old-style glass one I had lying around (15A)

tanked_darren Senior Enthusiast

tanked_darren

Posted
Posted

How did you come to using a 15A fuse?

 

I robbed a light out of a truck, and I tried to find the fuse in it just to see what GM was going with, but I was in a rush and couldn't find it.

mc7719 Enthusiast

mc7719

Posted
  • Author
Posted

Did a rough calculation based on a 55w bulb @12v.. Ideally I would have used a 10A, but 15 is what I had lying around lol

RAF Enthusiast

RAF

Posted
Posted

Nice job man

I just hope yours works better than mine. Half the time mine doesn't turn on

xPosTech Enthusiast

xPosTech

Posted
Posted

The ideal underhood light is one of the retractable types found on a late 80's to late 90's GM trucks and even a bunch of the cars and wagons. They detach and have about a 20' cord for changing flats, etc. Wind the cord back in the reel when you're finished. Magnetic base on most of them.

 

Definitely gonna put one on mine when I find it. No reason you couldn't fit it to the hood instead of the original location on the fender or firewall.

 

I'd check the wrecking yards. You can usually clean up the contacts and reflectors and maybe replace the cord if it's a little rusty. Gargle GM retractable underhood light for new ones but they might run $50-$90.

Ted

mc7719 Enthusiast

mc7719

Posted
  • Author
Posted
Nice job man

I just hope yours works better than mine. Half the time mine doesn't turn on

 

Could it be the angle you have it mounted? The mercury switch needs specific angle to move and turn on/off. I tried a few different places, and "bent" the bracket as necessary to achieve a solid on and off position.

  • 2 months later...
BigBlueLB756 Senior Enthusiast

BigBlueLB756

Posted
Posted

Finally got around to doing this mod today and it works great. Thanks to mc for the idea and tanked for the lead to the ebuy source.

electricchiken7 Enthusiast

electricchiken7

Posted
Posted

I think im going to have to try this mod. Where did you find the female connection to the harness. Just regular parts store like Advance or Auto Zone? Thanks for the idea. I wondered why these trucks didn't have these.

BigBlueLB756 Senior Enthusiast

BigBlueLB756

Posted
Posted

Clip off the connector; splice on enough RED wire to reach around to the underhood fuse panel; splice on an inline fuse holder, and end it with a lug for connection to the exterior stud on the fuse panel and you'll be all hooked up. Don't worry about the braided ground; the light is grounded through the screws into the hood.

 

All the details are in mc's post #1.

Thanks again to mc for this write-up.

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • Atlas
      GM discontinuing interior parts on a 5YO vehicle??

      By Atlas · Posted

      If one can't be found, a good automotive upholstery shop should be able to replace/sew in a new panel where the damage is on the old cover. It might not be the cheapest option..
    • Chuck FB
      first oil change - 2026 2500HD gas

      By Chuck FB · Posted

      Does your dealer charge you for the tire rotation on top of the oil change price ?. I haven't had any service work done at my dealer yet other than when I brought it back soon after owning it to have the front end aligned to correct the steering wheel being off center a bit. Oh they called me at least twice hounding me to bring it in for an oil change and pushing a 300.00 package of oil change and tire rotation and whatever other quick simplistic checks they would do. Only going off of what a friend gets charged for his half ton for the basic oil change and its the same amount of oil as the L8T holds, it was about 150.00. Once one buys a set of tires from most shops these days or so I believe, they will do free tire rotations and some do free tire balancing as well as free tire repairs.    Certainly doing a tire rotation is no five minute job, and definitely not at home but because I run a set of winter tires on their own wheels, I swap them at home and its a one tire at a time deal because of the tire season swap although I jack up the rear and do it and drop it back down and then raise the front and do them and coordinate the tire rotation into that process for both sets of tires. I am using a floor jack though and if I need to raise both ends at once I use a couple sets of jack stands to have all four tires off the ground. I use either an air impact or battery impact and have electric impact as well so no shortage there of easy methods to spin the lug nuts, and then retorquing the lug nuts. None of it goes quick though but my wages are cheap though ... zero. I live an hour out of town, its easier just to do things like that myself than waste a bunch of time in town and having to make an appointment and probably a special trip and sit there at the tire shop waiting for them to get my vehicle in and get it done and not screw something up in the process. 
    • mrbflat
      Clunk when coming to a stop... driveshaft/slip yoke? Mechanic couldn't recreate it

      By mrbflat · Posted

      I do have the 8 speed.  Interestingly enough, after driving my truck for the past 2 days now, I have not had the clunking issue at all!  I am beginning to think it may have been suspension/leaf spring related, and somehow when the shop put my truck on the lift to do their initial inspection, it relieved some built up tension/pressure that was causing my problem.  I swear it felt I was a bull rider on a bucking bull the way the truck would almost rock back and forth slightly before the big thud/clunk when coming to a stop.  I am hoping I got lucky here and it's gone for good.
    • Pryme
      first oil change - 2026 2500HD gas

      By Pryme · Posted

      Bring it to discount tire. They do free rotations even if you didn’t buy your tires there. I didn’t believe it until I tried and they did. You can tip the employee if you would like 
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      Best part of this video is how it resets expectations. Wonderfully done piece. It also made clear a few points I've made from day one. Detergent oils DO NOT KEEP A MOTOR CLEAN at the recommended or longer change intervals. They just get dirty slower than a non-detergent oil and there isn't spits difference between them on this point if they carry the DEXOS license. Great thing about the license that gets missed is it assures CONFORMITY even it that means a low bar.    One thing he did not talk about that I paused on an magnified was the condition of the oil ring separator. Besides a stuck ring a plugged separator and land drain back is huge when it comes control. We see in short order improvement in control IF that is the problem.    Another item I took exception to and he did not make plain was the condition of the timing chest and under valve cover having something to do with indicating piston cleanliness. Schaeffer's Oil makes that same omission in their million mile Ford video. I'm guessing he has never torn down a Red Line HP, AMSOIL SS motor that has been on that diet from the get. What he showed in the video was a good deal of varnish. Something totally absent in Peppers 165K cover off look. I smiled because he did his at the same milage.    He also makes the mistake of assuming oil temperatures in the pan are the temperature all over the motor even though he makes note of the piston being the hottest part of the engine. that baffled me a bit.    I can tell you from personal experience and witnessing teardowns of family motors that even oils of the 1960's would keep them squeaky clean when OCI's were 1500 to 2000 miles without exception. At 3K and above you get what he experienced and the longer you leave it the quicker to gets to the junkyard.    I think his is missing a opportunity not tearing it down again when he's done killing it. Time would be his only cost. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...