Jump to content

iGo Primo has been released!

wottenad

By wottenad
in Audio, Electronics & Software

Recommended Posts

  • Replies 68
  • Created
  • Last Reply
gawillet Enthusiast

gawillet

Posted
Posted

My OGM1 and GM1 backup camera are out for delivery! I'll have a fun saturday installing it all!

RAK80 Enthusiast

RAK80

Posted
Posted

My OGM1 and GM1 backup camera are out for delivery! I'll have a fun saturday installing it all!

 

 

You are going to love it. I should have the iGo update installed next week sometime! Congrats on the purchase.

parshal Enthusiast

parshal

Posted
Posted

The only thing that I've noticed with iGo that doesn't work quite right is the elevation. I took a trip to Kansas where I drop over 2000 feet in elevation. When I was following a route I changed the three available windows in the lower right corner to have ETA, clock and elevation. The elevation never changed. I'm sure that's an issue with iGo and there's nothing Advent can do about it. I love the new system!

parshal Enthusiast

parshal

Posted
Posted

Mine had great reception. I was changing elevation at a fairly rapid rate and it never changed. I'll need to check it again, though.

turbo06 Enthusiast

turbo06

Posted
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

RAK80 Enthusiast

RAK80

Posted
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

 

 

Eww I don't like the sound of that....reconsidering

wottenad Enthusiast

wottenad

Posted
  • Author
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

 

 

Haven't heard of this issue, so I'd be curious - have you tried reinstalling the current firmware?

 

I had issues trying to get it to load in one of our units, then did a firmware reinstall and it worked like a dream...

turbo06 Enthusiast

turbo06

Posted
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

 

 

Haven't heard of this issue, so I'd be curious - have you tried reinstalling the current firmware?

 

I had issues trying to get it to load in one of our units, then did a firmware reinstall and it worked like a dream...

 

No this is a new unit that came with the new igo installed. How can I reinstall it? Thanks Walt
wottenad Enthusiast

wottenad

Posted
  • Author
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

 

 

Haven't heard of this issue, so I'd be curious - have you tried reinstalling the current firmware?

 

I had issues trying to get it to load in one of our units, then did a firmware reinstall and it worked like a dream...

 

No this is a new unit that came with the new igo installed. How can I reinstall it? Thanks Walt

 

 

Go here and and D/L the firmware, then follow the instructions on the page.

 

Shouldn't take more than 10 minutes total.

turbo06 Enthusiast

turbo06

Posted
Posted

I have the new system. There is a lot of stuff different on the igo primo. The radio lags a lot more when changing volume and stations now. I had the first ogm-1 with the navmate and there was no lag. Also on iPod the album art doesn't hardly ever come up now, and always came up before. Its like there is not enough ram in the unit now. A little window has popped up a couple times to say system memory is low then the radio reboots. The new nab is awesome but it seems to hog the memory though. Hope the new update fixes these issues.

 

 

Haven't heard of this issue, so I'd be curious - have you tried reinstalling the current firmware?

 

I had issues trying to get it to load in one of our units, then did a firmware reinstall and it worked like a dream...

 

No this is a new unit that came with the new igo installed. How can I reinstall it? Thanks Walt

 

 

Go here and and D/L the firmware, then follow the instructions on the page.

 

Shouldn't take more than 10 minutes total.

 

Ok I will try that. This morning I pulled the sd card out and the radio worked great now. Lightning fast again and album art comes right up. So it must be the map sd card.
Tony1970 Enthusiast

Tony1970

Posted
Posted

Heyy.........

 

First post...........

 

Bought the OGM 1 in April of 2011.....Great unit....looks good in the dash

 

Sounds way better than the stock radio....my Enclave has BOSE

 

The Nav software is terrible....when I input a route and start driving it...takes

 

the unit several minutes to even lock on to it....no speed info.....no lane assist

 

Audiovox produced a unit that looks great and performs well

 

Why the hell did they put such a sucky Nav on it???

 

I hated that Nav software so much that I put my Garmin back on the dash

 

I guess they agree with me as they have changed it to the IGO Primo

 

Question....How do I get the new IGO for my beloved OGM 1

 

Would we have to pay for the upgrade?? We really shouldnt have to after

 

Spending so much on the head unit and evaluating Advents mistake

 

Yes I have the latest firmware of Oct 28 2011

 

And yes Im also a fan of ADC.....Walt is a gentleman...and runs a first class operation

 

Please help

 

Tony

Tony1970 Enthusiast

Tony1970

Posted
Posted

Hey....

 

This question may be for Walt...or anyone that knows

 

Did Advent change the OGM 1 in any way to accept the IGO primo??

 

Will this new nav software work flawlessly on any OGM 1??

 

Tony

Archived

This topic is now archived and is closed to further replies.

Go to topic listing

  • Latest Articles

  • Posts

    • needafix
      2019+ Brake failure, it's complicated

      By needafix · Posted

      I'm not sure if this should be a new topic, let me know if it's out of place. This my first post. Thanks 85077522 - AC Delco GM Genuine Parts Brake Master Cylinders. Anyone else had to replace this brake master cylinder yet. I didn't do any brake work, it looks like new parts and I've had the truck for about 4k miles, 119k total miles.  When it started to throw codes I did the calibrations with a bidirectional scanner and got the codes to clear but they came back so I did the routine; base bleed, automated bleed and final base bleed. All that with Bosch ES16-32N fluid (please look it up). That seemed to fix it but 100ish miles later it failed again so I ran the same process but with a pressure bleeder this time and got the same results, fixed for 100ish miles. The original fluid looked bad and I thought I got most of it out, it could've been the wrong fluid. The codes; P25A2, C05B0-00, C2A1B. I can get them to clear but not for long. The C05B0 indicates a leak in the front circuit (which is bone dry) so I'm thinking of doing the bleed process on that front again today and I don't know if that's taboo to just do the front but at this point it seems like it's worth the try anyway. The new master cylinder/module unit is supposed to get here today. But now I'm pretty much convinced this install is over my head. I've called several shops and some mobile guys that I know but this thing is like radio active material, scary wise. I did get 2 local shops say they should be able to do it, one says he has the SPS2 programing capability. And with the battery disconnected is there supposed to be pedal resistance, mine is to the floor, then if I pump it I can get some resistance. I had a panic stop prior to this issue which may have contributed from what I read. And on the first attempt to bleed and hydraulic test the scanner listed things to look for and one was any gaps between the pad and rotors which I did notice on the RF corner and I removed the outer pad (where the gap was) cleaned it and the hardware and didn't see a gap after that but will re-check it. I read that if pushing the caliper pistons back then you're supposed to open the bleeder so as to not push fluid backwards into the abs module or it will damage it. If that's true then that's also a possibility from the previous owner having the brakes changed before I got it. I'm using an XTool ip500 scanner. Any suggestions, questions and comments welcome. 
    • Donstar
      Navigating senior years.

      By Donstar · Posted

      Next Friday will be my 6 week point from my right knee replacement.  The surgeon says it will be fine if I choose to drive after this checkup.  I know I could drive now but best to do as my surgeon (and my wife) tell me.  Richard compared being 62 to 72.  I remember when I was in my early 60's I was experiencing slow but regular decline in my mobility.  Thanks to good medical support,  i continued to fight the speed and spread of this decline. During my 60's I worked on non-surgical methods and just when I turned 70, my orthopedic surgeon recommended joint replacements.  In a little over a year, I had one shoulder and both knees replaced.  This hasn't been a terribly fun experience, but worth the discomfort as my future mobility health trajectory has reversed.  It is a treat to now be watching my mobility. balance and confidence steadily improve!
    • Another JR
      Trailer TPS Sensor Question Rim Size

      By Another JR · Posted

      Grommets with the right cement should be perfectly fine. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      This is going to take allot of Assembly    
    • PunchT37
      Transmission Temperature Hitting 220s

      By PunchT37 · Posted

      Why do they have the gas 10l80 opening at 145?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...