Jump to content

Differential Drop kit

ctisdell
 Share

Recommended Posts

ctisdell Enthusiast

ctisdell

Posted
Posted

Does anyone know where I can get my hands on a differential drop for my 2004 1500 Z71 Silverado?

ctisdell Enthusiast

ctisdell

Posted
  • Author
Posted

To lower my cv angles.

KMGZ400 Senior Enthusiast

KMGZ400

Posted
Posted

A diff drop would be unnecessary for just a leveling kit.. My keys are cranked about 2 and a half inches and i have about 145k now. original front end parts

ctisdell Enthusiast

ctisdell

Posted
  • Author
Posted

Theoretically by dropping the differential with a leveling kit would bring the cv shafts closer to flat, this would then create less wear on them. Once again this is just a theory!

kstruckcountry Senior Enthusiast

kstruckcountry

Posted
Posted

I briefly ran a 1.5" diff drop with my 2" leveling kit. I would always take flat cv angles if I could.

Did you have any issues with clearance on any of the front end parts? I would raise mine if the CVs would be flat.

KMGZ400 Senior Enthusiast

KMGZ400

Posted
Posted (edited)

I really dont see it as being necessary at least on a GMT800 with t bars, i know too many people who have gone 200k plus on a leveling kit not having anything wear out prematurely. But that's just what I have seen from my experiences.

 

im not saying leveling dosent wear anything out faster.. but still

Edited by KMGZ400
ctisdell Enthusiast

ctisdell

Posted
  • Author
Posted

Like I said its just a theory!

blackout07 Senior Enthusiast

blackout07

Posted
Posted

No clearance issues at all. I left it on after I pulled the Junk Country 3" kit and went back to a 2" leveling kit. If you cn find one, and you want one, then go for it. 2" of angle isn't much for any truck, but .5" of angle is always better...no matter how you look at it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • bwiese
      seat base height *lowering* (base 40/20/40 seat, 2026 1500 WT std cab)

      By bwiese · Posted

      Folks, Have a great new 2026 WT  (std cab, 2.7/4WD) w/base 40/20/40 mech adj bench "fake buckets"  (with lower and upper center console) heavy vinyl seats.  Overall the seats are very comfortable and the vinyl is heavy and appears less likely to 'split out'. Am very tall (6'5")  + a bad back/osteporosis/former hyperparathyroidism so ease/range of movement is a bit restricted.  The truck rides a bit high and I use a nerf step bar w/my left foot to step in, then I put right foot/leg in, drag my butt in  & get seated.  Worked fine in my 2018 RAM quadCab. But I end up dragging my butt over the left raised sidecushsion area of vinyl seat, and due to texture there's fair amount of traction on slide inward.  (ArmorAll didn't improve.) If the seat were even ~1/2" - 3/4" lower it'd be helpful, but base seats just have the forward/backward underseat bail and the side lever for tilt which really doesn't affect seat height.   I really don't want to 'de-puff' the left side sidecushion forming the  fake 'bucket'. I know one company sells 'seat elevator blocks':  but is there a simple way of lowering the height of the driver seat instead?   Thanks Bill W San Jose  
    • bwiese
      on-wheel cellphone control: 2026 1500 WT (2.7L 4WD std cab)

      By bwiese · Posted

      I have a basic 2026 1500 WT  (2.7L/4WD reg cab shorttbed). Comfy, generally happy with electronics/radio - but is there a way I can add switches to steering wheel right-side position (curr. empty) so I can adjust volume, push phone button to voice dial, etc? Bill W San Jose  
    • Tyler Gibbs
      Travel Trailer 2024 2500 HD 6.6 Gas Engine ?

      By Tyler Gibbs · Posted

      The curb weight on a 1 ton crew cab long bed is around 7k lbs.  Now, I don't know where you went to school but 9k is not more than 2x 7k lbs. More than 2x 7k lbs would be 14k+.   With that said, obviously yes you're going to feel a 9k lb trailer when slowing down.  I already said, when accelerating.  When changing lanes?  No.  But if you look at the context of what was quoted, the original person said, "after a mile or two..." which means that would be after the accelerating portion and you're driving a generally steady pace.  Please do learn to read and comprehend.
    • sFrank
      2026 Silverado Range AFM DFM ECU loaction

      By sFrank · Posted

      So I purchased the Range unit for my 2026 and I am seeing different locations suggested for the ECM . Can anyone confirm wither under hood, left side or right side or behind the wheelwell?
    • No F-bdy Bs
      Dave's Auto (custom engine builder) tear down of L8T

      By No F-bdy Bs · Posted

      Like I've said before. Di and Carbon buildup is not that big of a concern. Engine had minimal buildup, and that engine was obviously not super well maintained. Do regular oil changes, and you're gtg as long as the rest of the truck lasts. Also, the High Pressure FP that people ****** about, but can't tell you why.  Now, I wish they'd trash the variable oil pump. No real world issues with them, but I'll gladly eat whatever miniscule MPG it's saving me in favor of more oil at all RPMs.    Curious to see his assessment of the 7.3 compared to the 6.6. I expect he'll praise the port inj, but from a structural standpoint, the 6.6 is as robust as any engine out there.    Not to take away from the 7.3. I feel it's equally as good as the 6.6.     As to heat on the rear cyls, I'd have to see numerous examples before I'd say it's an issue. Especially not knowing the history of that engine. For all is known, they could have blown a rad hose, and ran it hot, and the 2 rear cyls may be the first to get hot in a low coolant situation, but not be an issue aside from that. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...