Jump to content

Under seat storage?


Recommended Posts

Posted

Anybody have any expeeriences or opinions on which underseat storage to get? IE: Husky,DuHa,GM?

Posted

Anybody have any expeeriences or opinions on which underseat storage to get? IE: Husky,DuHa,GM?

I use two of the short red COKE crates... Didn't cost much and they fit just fine under the back seat, hold a lot of stuff, and can be quickly removed any time needed.

Posted

I was considering GM and Husky for my crew. Just purchased the Husky on Realtruck about an hour ago.

 

 

Sent from my iPad using Tapatalk

Posted

Thanks much jeffsig i was wondering about the husky if it followed the contour of the 2015 rear seats. Apparently the DuHa doesnt. I don't mind the look of the Husky at all, i think i will be going this route. It looks black in color is that correct? Which rear floor mats are you using and when the seat is folded down is there any gaps between the seat and the husky storage unit?

 

Thanks in advance.

Posted

Let us know what you think of the husky Johnnyace. Send a pic or two if you don,t mind.

 

Thanks

  • 2 weeks later...
Posted

Does anyone make one with a lid? It would be nice to have the seats up and the dogs not stepping all over your gear

 

 

Sent from my iPad using Tapatalk HD

Posted

Also went with the Husky. A bit pricey perhaps but it does the job and have no complaints.

 

3BBE6553-FAB8-49EB-9B94-4067B82C77ED_zps

  • 1 month later...
Posted

Went with the husky. Not the best option for the money but still better than throwing stuff under the seat and hoping it wont slide around or stepping on it.

 

Thanks to all for your posts.

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,791
    Total Members
    8,960
    Most Online
    d.lowrey
    Newest Member
    d.lowrey
    Joined
  • Who's Online   1 Member, 0 Anonymous, 2,944 Guests (See full list)

  • Latest Articles

  • Posts

    • Just did an injector/HPFP replacement on Pepper at 192,400 miles; close enough to 200K, RIGHT? (If 200K is considered life end and to me it isn't). But hey, to each his own.    Have never run a catch can on this vehicle. Back side of every valve looked like a new valve spray painted semigloss black. Port walls looked 'neat' (all a normal result of passive EGR via VVT) Zero build up even in AFM cylinders. Just color. It uses no measurable oil and never has.    At 155,000 I put her on E-85 and a borescope of the cylinders at plug change showed very clean pistons and valve faces. The replaced injector tips looked new. (It was the pump piston seal that was leaking). Oh well, have six good backups.    Still gets 28 mpg on gas (highway average) and over 20 (highway) on alky. UOA's look good and runs as good now as it did when I bought it. Better in fact.    What improvement would a Catch Can provide this motor?     And given all this I expect that IF I installed one I'd see some water/gas/oil vapor accumulation. Byproducts of normal combustion.   Having said that, IF my motor used an appreciable amount of oil I'd consider it a useful 'crutch' until I had the situation corrected OR if bore polished, until I junked it or rebuilt it to stave off repeated plug fouling.    I'm not telling you what I THINK. But what its DONE.          
    • Love the look. I'm a SCSB lover myself.    Two items. 1.) A spacer changes scrub radius but this also changes when we use wheels of different offsets. A little isn't a big deal. 2.) Steel wheels, alloy wheels all have different thickness. Same effect on the stud and lug nut as a spacer. When hub centric the wheel isn't supported by the stud. It's supported by the hub. The stud just keeps it all together.  
    • I had a evap sol go bad a couple weeks ago. . I replaced it.  While watching live data at the time I saw I had some cylinder 1 misfires. No MIL but on live data I could see ~50 at startup and about 70 more after an hour a drive all on cyl 1.  I also noticed that the LTFT were -5% to -15% always.  And that bank 2 is always -3% richer than bank 1. Even across all driving modes, city, highway, etc it’s always 3% richer than bank 1. So I start with the misfire. Swapped coil, plug, and plug wires from 1 to 3. No follow. I got an Injector reseal kit, pulled the D/s injector rail, swapped #1 and #3 injectors, resealed them, reinstalled and retested.  The misfire followed to 3. So I ordered and replaced all 8 injectors, spark plugs, and plug wires. Also replaced the 1 time use fuel pipes under the intake manifold.  Injectors that were in the truck since new were  Part # 12668390.  I replaced them with # 12742701 Got from RockAuto. Pretty certain they’re genuine and the correct ones. I called a friend at a parts store who told me “the 12742701 were the correct superseded part # for the originals I was replacing”. So started truck after replacing all that and it’s running -15 - -30 LTFTs. I reset the fuel trims with GDS2 and drove it for a 60 miles trip each way. There have been no changes in the LTFTs.  I checked if the HPFP was leaking into the crankcase. I removed the pvc and watched the trims. No difference.  I checked the alcohol content and it was at 10%  I’m out of ideas here. Truck seems to run great. Just always rich on the fuel trims.  Anyone with any help or ideas would be greatly appreciated.  I ran an injector balance test just for the heck of it and it came back this. I’m confused.  I have gds2 and some other diag tools if anyone knows of anything I should test next.
    • Definitely needs to go back to the dealer. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...