Jump to content

Recommended Posts

Posted

I'm looking to replace my idler and pitman arm, but there are 2 options. I don't know if I have the 3 or 4 groove.

 

My real question is, if I'm replacing both at the same time, can I just buy the same corresponding ones, and they will work? What exactly does the grooves line up to?

 

I suppose I can buy both options, but if I don't have to, I won't.

Posted (edited)

I'm looking to replace my idler and pitman arm, but there are 2 options. I don't know if I have the 3 or 4 groove.

 

My real question is, if I'm replacing both at the same time, can I just buy the same corresponding ones, and they will work? What exactly does the grooves line up to?

 

I suppose I can buy both options, but if I don't have to, I won't

 

Depends. If you buy the idler arm with the mount bracket and not just the idler arm, you would have to match up the spline count on the arm you take off. On the pitman, it is based on the pitman splines out of the steering gear. You may be able to see how many splines there are if you remove the nuts off of them, or you may just have to pull each arm off then order the correct match. Its either 3 groove (33 spline) or 4 groove (32 spline). Typically 2500HD are 3 groove, and 1500 are 4 groove from what I've seen.

 

I'd go as far as to get the idler with bracket yes. If that has never been greased especially. Some people miss that top grease fitting on the bracket.

 

If the pitman is 3 groove, the idler should be as well, same if it is 4 groove, the idler should match.

Edited by 15HDriver
Posted

And that's my dilemma. I have a 2500, non-HD.

 

Based on what you're saying, if I buy all new pieces that match with each other, it should work?

Posted

And that's my dilemma. I have a 2500, non-HD.

 

Based on what you're saying, if I buy all new pieces that match with each other, it should work?

 

Correct. I'd start with the pitman first and match the idler to what you find for groove count (they should match already but I'd base it off of the pitman).

Posted

The idler arm has neither 3 or 4 grooves, so you can't really go wrong with that one, it has a taper for the 'middle' connection between the idler arm and the idler arm bracket assembly.

 

The pitman arm SHOULD be 3 groove for your 2500, but if you have the money and don't have a second vehicle, I would get both and then return the one you don't use.

Posted

Thanks davester! The only reason I was asking on the idler arm was because Rockauto lists idler arms that go with either the 3 or 4 groove.

 

I pulled the trigger on a complete MOOG front end rebuild, and gambled on the 3 groove pitman. In the mail is:

 

(2) Upper Control Arms

(2) Lower Ball Joints

(2) Outer Tie Rod Ends

(2) Inner Tie Rod Ends

(1) Pitman Arm (3 groove)

(1) Idler Arm

(1) Idler Arm Bracket Assembly

Posted (edited)

When installing the idler arm/bracket, I couldn't find what the torque for the bolt between the two pieces should be [between the idler arm and idler arm bracket], so I just picked a bit more than the torque for the pitman arm [as they are both taper connections...

 

The service manual for my truck treats it as a single unit.

Edited by davester
Posted

On my 03 you can get to it from under the hood if you have a table or step ladder.

 

Underneath it can try your patience as the grease hose must make a sharp angle to couple the alamite. There are adapters for this, but .....

Posted

Thanks for the tips guys! Looks like the parts should be here Friday, which means I may start tackling it this weekend. I'm gonna study my Chilton's manual as well and see if that has any other tips.

 

I'll try to take some pics along the way.

Posted

Of, yeah, depending on the size of your pitman arm puller, you may find it easier to use if you loosen the bolts holding the steering box, so you can get a bit more clearance for it. And doing this also helped with getting a straight shot with a socket/torque wrench for tightening the pitman arm nut.

Posted (edited)

I did exactly what you did, but also added the cognito motorsports pitman idler support bracket to eliminate any future problems and correct the factory issues. I also added their super strong tie rods. My truck is not lifted, and has stock size tires.

 

http://www.cognitomotorsports.com/pitman-idler-support-kit.html

 

 

Thanks davester! The only reason I was asking on the idler arm was because Rockauto lists idler arms that go with either the 3 or 4 groove.

 

I pulled the trigger on a complete MOOG front end rebuild, and gambled on the 3 groove pitman. In the mail is:

 

(2) Upper Control Arms

(2) Lower Ball Joints

(2) Outer Tie Rod Ends

(2) Inner Tie Rod Ends

(1) Pitman Arm (3 groove)

(1) Idler Arm

(1) Idler Arm Bracket Assembly

Edited by vucelick
  • 3 weeks later...
Posted

Well, I finally got it all wrapped up. Some parts were a breeze, and some parts were slightly more difficult. Here's some notes for anyone looking to do this in the future:

 

Upper Control Arms - Since a complete upper control arm with new bushings only cost about $20 more than just the ball joint, this was a no brainer. Not having to press and ball joints or control arm bushings definitely comes in handy if you don't have access to a press. This also saves time. The bolts on the control arms were kinda trick to get out. They were slightly stuck and took some "convincing" to get out. I had to remove the shock to get enough access to swing the mini-sledge to knock the bolts out. After that, just replace and reverse procedures. Pretty straightforward.

 

Lower Ball joints - This one was a lil difficult for me. The ball joint press didn't knock these out, so I headed over to YouTube. This video was a huge life saver!

 

 

 

I just followed along and let the 3lb sledge knock the ball joints right out. The ball joint press put the new ones in easy as pie.

 

Tie-rod ends - I originally wanted to leave the center link in and just replace the inner and outer tie-rod ends. I couldn't get enough leverage to break to parts loose when this was installed. Now, the tie-rod end tool would have easily accomplished this task. However, since I was replacing the idler and pitman arms I knew the whole steering linkage was coming out. At that point, I just put the center link on the vice and was easily able to remove the tie-rod ends. Assembling the new tie-rod ends was easy and I was able to match up the lengths so it would be close to how it was when it came off the truck. My only gripe is the MOOG grease zerks would not go in. I had to use the old zerks to thread the new parts before I could attach the new grease zerks. Not a huge deal, I didn't break anything or lose any time.

 

Idler arm (and bracket) - Definitely replace both of these at the same time. The new bracket comes with a grease zerk relocation line so that you can make it easy to grease in the future. I mounted mine to one of the bolts on the sway bar where it attached to the frame. Really easy and straightforward. Remove and replace.

 

Pitman arm - This was the only part I wasn't convinced I could tackle easily. With the differences in parts (3 or 4 groove), I was instantly doubting myself. I bought the 3 groove, and was ready to replace it. When I went to look at replacing it, I noticed I had to move the steering gear box to gain enough access to remove the pitman arm. I was expecting a huge headache fumbling around in that tight space. So I held off and decided to wait until I was going to replace the gear box later down the road. There were 2 gear box options (33 spline or 32 spline), and I was instantly confused again. I shot in the dark and ordered the 33 spline so I could replace everything at once. Turns out the 3 groove pitman arm attaches to the 33 spline gear box. And just for reference, the 4 groove goes with the 32 spline. Makes sense now that I saw how they went together. Replacing the whole unit ended up saving a huge chunk of time versus just replacing one stuck part in tight quarters.

 

Steering gear box - I held off doing this because I thought it would be a pain to do. But, this needed to be done since it was leaking a ton of fluid. After looking at it further, it's only 3 bolts that hold it on there, and they are right on the frame. Really easy to get to. The steering linkage is held on by 1 bolt, and then it comes right off. Quick tip, MAKE SURE YOU DO NOT SPIN THE STEERING WHEEL WHILE THIS IS DETACHED!!! The wires in the steering wheel can easily get pinched and damaged because there is no stop to keep it from spinning. The power steering fluid lines were kinda tricky to break loose, but I was able to do it without breaking them. Then the whole piece came out really easy with the pitman arm attached (after the bolt on the center link was removed of course). From there I was able to attach the new pitman arm to the new steering gear box using the old as a reference, and then re-assemble. I waited to put the lines back on the new gear box until it was bolted to the frame, which was very time consuming because the 18mm wrench could only move about an 1/8 of a turn at a time. Same thing when I was removing it, but I didn't consider that because I was just excited I didn't break the lines. I would suggest trying to attach the lines before you bolt it to the frame, just be careful about how much play you have with the hoses.

 

All in all , I spent around $600 for all MOOG suspension pieces and an ACDELCO re-manufactured gear box. RockAuto was my go to on this, and they delivered big time! The local shop quoted me $2,300 to do all of this work. Even if you had to buy the ball joint press and pitman arm puller, you would still come out way ahead. This work was completed with 275,000 miles on the odometer.

 

Well, off to get an alignment and then hit the road!

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Forum Statistics

    250.4k
    Total Topics
    2.7m
    Total Posts
  • Member Statistics

    342,825
    Total Members
    8,960
    Most Online
    phillja
    Newest Member
    phillja
    Joined
  • Who's Online   5 Members, 1 Anonymous, 798 Guests (See full list)

  • Latest Articles

  • Posts

    • If we're talking futures, yes, it's speculation.   The spot price of a delivered barrel is elevated now compared to before the conflict. And that is related more to current supply/demand.
    • SPECULATION on the wars effect raised prices. AI is maximizing the profit. Refining is vertically integrated. 
    • It's the Middle East conflict that raised prices, not AI. But nice distraction.
    • Lauren Fix Is AI quietly deciding what you pay at the gas pump? How the algorithm picks drivers' pockets.   Every time tensions flare somewhere in the world, gasoline prices seem to jump overnight. Drivers expect it. The news blames geopolitics, oil traders blame uncertainty, and politicians blame each other. But here's the question almost nobody is asking: If computers can raise prices within hours, why do they suddenly become so patient when it's time to lower them? Americans have lived with this frustration for decades. The price of crude oil climbs, and gas stations respond almost immediately. Crude oil falls sharply, and suddenly we're told to be patient. Refiners need time. Distributors need time. Retailers need time. Somehow, that urgency only seems to work in one direction. Regulators have already gone after algorithmic pricing in apartment rentals, and they're looking at hotel rooms, airline tickets, and online retail. Now a new California lawsuit and a federal push to investigate gasoline pricing suggest there may be another piece of the story that deserves far more attention. It isn't simply about oil markets anymore. It's about artificial intelligence, algorithms, and whether software designed to maximize profits is quietly changing how fuel prices are set across America.   If that sounds like something out of a science fiction movie, think again. Kalibrating the market? Kalibrate is a real pricing platform. The company markets its software as an advanced pricing solution that analyzes competitor prices, wholesale costs, local demand, traffic patterns, and countless other variables before recommending the "optimal" price at the pump. By the company's own marketing, it serves many of America's largest fuel retailers and convenience store chains. Retailers use it because it promises to increase profit margins while staying competitive. There is nothing inherently illegal about any of this. Every major industry now runs on data analytics. The concern begins when pricing software stops simply reacting to the market and starts shaping it. On June 22, three California drivers filed a federal class-action lawsuit in Sacramento — and they didn't just sue the software company. They sued the gas stations. Kalibrate is the lead defendant, but so are Marathon, BP, Circle K, 7-Eleven, Speedway, Walmart, Sam's Club, and Albertsons. According to the complaint, Marathon alone runs more than 1,000 ARCO stations in California and has been letting Kalibrate set prices at them since 2020. Circle K, plaintiffs claim, has more than 400 stations on the software. Albertsons, they allege, has been using it since at least 2009. The complaint alleges that Kalibrate allowed competing retailers to share competitively sensitive information and receive pricing recommendations that discouraged aggressive competition. It describes a "restoration" feature that plaintiffs say lets nearly all the stations in a market raise prices at the same time. It also quotes Kalibrate's marketing, which according to the complaint tells operators that even in the face of "falling oil prices ... it's critical to avoid a race to the bottom," and warns that cutting your price to win customers "could be making a change that triggers a downward spiral." The plaintiffs call the platform the "central nervous system for a conspiracy to extinguish retail price competition among gas stations." Price pumping What does that cost you? Research cited in the complaint found that stations switching to this kind of software raise prices by about 6 cents a gallon on average — and by as much as 30 cents where most of the stations in an area are running it. Plaintiffs point to a real-world example too: They allege that when one California Albertsons turned Kalibrate on, its pump price climbed 3 to 4 cents within days. That sounds small. It isn't. By the complaint's math, a single penny on the statewide average drains $134 million a year from California drivers' wallets. Kalibrate says it disagrees with the allegations, calls its technology lawful, and intends to defend itself. The retail chains have not yet answered the complaint. No court has ruled on any of it. But what happens when thousands of competing businesses begin relying on the same algorithm to determine prices? Price fixing has been illegal in California for more than a century, and the plaintiffs are suing under that old law. What's new is a statute that took effect on January 1 — AB 325, the Preventing Algorithmic Collusion Act — which says plainly that you cannot escape a price-fixing charge by routing the conspiracy through software. Using pricing software is still perfectly legal, but using it to coordinate with your competitors is not. AB 325 makes it unlawful to use or distribute a "common pricing algorithm" — software that uses competitor data to recommend, align, or stabilize prices — as part of an agreement to restrain trade. Whatever you think of Sacramento, it closed that loophole first, and this case is the first real test of it. The A-word Washington is applying pressure of its own — though it is worth being precise about what kind. On July 3, the Department of Justice and the Federal Trade Commission sent every state attorney general a letter urging them to investigate whether antitrust violations or price gouging are keeping gas prices artificially high. "Recent volatility in crude oil prices does not suspend either the antitrust laws or state consumer protection laws," they wrote, "and it does not authorize companies to manipulate retail prices or collude with their competitors." The letter followed President Trump's complaint, posted to Truth Social on June 23, that falling crude prices weren't reaching drivers. But read that letter closely and you'll notice something. It never mentions algorithms. Not once. The federal government is going after gas prices with the same tools it has always used, while the argument about the software is being made by three drivers and their lawyers in a Sacramento courtroom. Nobody in Washington has said the word yet. And whether any of these investigations turns up illegal conduct remains to be seen. Anyone who has driven for more than a few years knows the pattern. Prices spike within days of a geopolitical event, then drift down at a painfully slow pace. Economists even have a name for it: the "rockets and feathers" effect, and they have studied it for decades. Researchers point to several reasons, including inventory replacement costs, consumer behavior, and local competition. None of those explanations necessarily involve illegal activity.   Dirty work   But artificial intelligence introduces an entirely new variable. Unlike traditional pricing models, today's software can monitor competitors continuously, process enormous amounts of market data instantly, and recommend price changes faster than any human pricing manager ever could. If dozens or even hundreds of competing retailers rely on similar recommendations generated from comparable market data, the practical result may be less price competition — without anyone ever picking up the phone to coordinate prices. That possibility isn't unique to gasoline. Regulators have already gone after algorithmic pricing in apartment rentals, and they're looking at hotel rooms, airline tickets, and online retail. The Justice Department sued RealPage over the software landlords used to set rents and settled the case last November. The concern in every case is the same: that algorithms may accomplish indirectly what competitors have long been prohibited from doing directly. It's worth being precise about what that settlement did and didn't say. RealPage paid no penalty, and the government made no finding that it broke the law. What the DOJ objected to was the use of nonpublic information from competing landlords — not the software itself. Using an algorithm to price your product isn't illegal. Feeding it your competitors' private numbers is where the trouble starts. That distinction is going to decide the gas station case too. Technology moves faster than regulation. Thin margins This debate also exposes another misconception. When Americans get angry about gas prices, they aim that anger at the oil companies. In reality, what you pay at the pump includes crude oil costs, refining expenses, transportation, taxes, distribution, and retail pricing. Gas stations generally operate on thin per-gallon margins — the National Association of Convenience Stores puts the net at roughly a dime a gallon once credit card fees and operating costs come out — while state taxes and regulatory costs can dramatically affect what you pay locally, particularly in a state like California. If gasoline prices are rising because of global supply disruptions, consumers may not like it, but they can understand it. Markets move. Wars affect energy. Hurricanes interrupt refining. But if pricing software is reducing competition by encouraging retailers to move together instead of competing aggressively for customers, consumers deserve answers. Artificial intelligence is quietly becoming the invisible middleman in countless financial decisions Americans make every day — insurance rates, airline tickets, hotel rooms, online prices, and now what you pay every time you pull up to the pump. Most consumers never know an algorithm was involved; they simply assume that's what the market decided. Algorithms don't care whether you're commuting to work, driving your kids to school, or trying to keep your small business afloat. They don't understand household budgets or family vacations. They optimize. That's what they were built to do. The question was never whether artificial intelligence can set prices more efficiently. It's whether we've quietly allowed machines to redefine what competition means. Because if software can determine the price of something as essential as gasoline today, what will it be deciding tomorrow?   https://www.theblaze.com/lifestyle/is-ai-quietly-deciding-what-you-pay-at-the-gas-pump  
    • All valid.   But.  How many people really do this?  Its few and far between.  Most just drop it into D and go.  
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...