22" Fuel Wheels with Nitto Trail Grappler M/T 2011+ 2500/3500 8 Lu
-
Similar Content
-
- 1 reply
- 3,729 views
-
- 0 comments
- 1,090 views
-
- 0 comments
- 953 views
-
- 0 comments
- 851 views
-
- 0 comments
- 845 views
-
-
Recently Browsing 0 members
- No registered users viewing this page.
-
Forum Statistics
250.4k
Total Topics2.7m
Total Posts -
Member Statistics
342,794
Total Members8,960
Most Online
-
Who's Online 9 Members, 1 Anonymous, 463 Guests (See full list)
-
Latest Articles
-
Posts
-
Wire Pinout and Colors Pin A: Brown/White - 5V Reference Signal Pin B: Black/White - Sensor Ground Pin C: Dark Blue - EGR Position Signal Pin D: Pink/Black - 12V Ignition Power Pin E: White (or varies) - Ground Control for EGR Solenoid [1, 2] Understanding the Wires 5V Reference: A low-power current sent by the Powertrain Control Module (PCM - the car's computer) to the EGR. Position Signal: Tells the PCM exactly how far open or closed the valve is. Ground Control: The PCM completes the circuit to actually open and close the EGR valve using this wire. [1, 2, 3, 4] This is what AI is telling me, in absence of access to a complete service manual for the truck. So there are two grounds and I think I determined one of them is bad. I need to run through the test sequence again to validate what I think might be a bad ground. I'll be honest, electrical isn't my strong suit, but I'm learning. -
That remote-start behavior is worth separating from the AFM/DFM side. A lot of plug-in modules depend on when the vehicle wakes up the OBD-II network and when the module initializes. Remote start can change that timing compared with a normal key/button start. I would not treat unplug/replug every time as normal daily use, though. If the main goal is Auto Start/Stop only, the dash button may be less annoying. If the goal is AFM/DFM behavior, then fitment and startup behavior matter a lot. -
As seen recently on the Leno podcast that’s the purpose of the Slate truck. The ease of customizing. As entry level as possible. It does come with AC. -
By asilverblazer · Posted
Not sure how many wires you've got to play with BUT if there is constant power AND ground at the EGR how is it switching? In other words, the grounding via the PCM to activate it makes sense to me. -
By asilverblazer · Posted
Right?! Could you swap out the lights to an older style? Did they say what circuit it had to detect resistance on? It shouldn't be the running lights because those aren't on all the time, it could be the brake/turn signal circuit(s), but it seems that there might be a scenario where I would want the trailer brakes at the same time as when those lights first illuminate to recognize the trailer in the first place. If it's the 12v +, to charge trailer batteries, maybe adding a battery backup break away to the trailer would resolve the issue.
-
-
GM-Trucks.com Clubs
-
Black Truck Club
Open Club · 612 members
-
White Truck Club
Open Club · 380 members
-
Canadian Owners Club
Open Club · 282 members
-
Red Truck Club
Open Club · 157 members
-
diesel 3.0
Open Club · 279 members
-
Texas Owner's Group
Open Club · 371 members
-
NorthSky Blue Club
Open Club · 118 members
-
Midwest Owner's Group
Open Club · 212 members
-
2015 Custom Sport Club
Open Club · 5 members
-
GM Snow Plowing Club HD
Closed Club · 14 members
-
-
Popular Contributors
-
.thumb.JPG.2c573de60d3a3a4407c7d92298db46dd.JPG)
Recommended Posts
Archived
This topic is now archived and is closed to further replies.