Jump to content

T1 Switched Power Source

2019_Silverado_HC
 Share

Recommended Posts

Zeker Enthusiast

Zeker

Posted
Posted (edited)

Did anybody figure this out for the 2019s? On my old truck there was already a footwell light but it was just a tiny bulb and only on the driver side. I added LEDs to both side and just used the existing wire. That worked great. Would love to add footwell LEDs to my Trail Boss that work with the dome lights.

Edited by Zeker
  • Like 1
  • 1 month later...
  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

2019_Silverado_HC
2019_Silverado_HC

I installed some RGB footwell lights this weekend (picture forthcoming) and part of the project involved locating a switched power source and preferably one with retained accessory power.  In the righ

Smoothbassman
Smoothbassman

Yes There is only one slot that is switched. It's the spade to the left of the 50 amp circuit breaker. Top right of this picture. You have to use a spade connection to grab it and split it off

Zeker
Zeker

Hooked mine up last night. Wired them into the dome lights. Thanks Smoothbassman!

Posted Images

Smoothbassman Enthusiast

Smoothbassman

Posted
Posted
Did anybody figure this out for the 2019s? On my old truck there was already a footwell light but it was just a tiny bulb and only on the driver side. I added LEDs to both side and just used the existing wire. That worked great. Would love to add footwell LEDs to my Trail Boss that work with the dome lights.
I'm working on it today. I'll find the right wires and report back. I got the 1st part done with wiring this into the accessory power.

c1d647860f43653f42b401746dafc062.jpg

Sent from my SM-N960U using Tapatalk

  • Like 1
Zeker Enthusiast

Zeker

Posted
Posted
On 9/14/2019 at 4:21 PM, Smoothbassman said:

I'm working on it today. I'll find the right wires and report back. I got the 1st part done with wiring this into the accessory power.

c1d647860f43653f42b401746dafc062.jpg

Sent from my SM-N960U using Tapatalk
 

Any luck?

Smoothbassman Enthusiast

Smoothbassman

Posted
Posted (edited)
15 minutes ago, Zeker said:

Any luck?

Yep.

 

I figured it out. 

 

As for the dome light I found the right wire in the harness that gives me the positive output that I need as well.   Pin 10 on the forward most BCM Connector.  2nd Gray wire.

 

I have that marked and ready for the rest of the install. 

 

In order to use this Kit how I want, I had to order a couple of set's of relays. Cost 10 bucks for these relays and all of the parts will be here on Weds.  I will assemble, bench test it Thursday and get it installed on Saturday morning.  I will have photos of everything after I get the wiring completed. 

 

It sounds complicated but it really isn't.  Just need an hour of time to wire everything up offline before getting back in the dash to install everything. 

 

More to come this weekend!

Edited by Smoothbassman
  • Like 2
bendo188 New Member

bendo188

Posted
Posted (edited)

Can anyone tell me if they found an accessory powered fuse in the passenger side fuse panel. I have tested everything there and everything is hot. Even the open spots.

Edit: Found it thanks 

Edited by bendo188
Smoothbassman Enthusiast

Smoothbassman

Posted
Posted
Can anyone tell me if they found an accessory powered fuse in the passenger side fuse panel. I have tested everything there and everything is hot. Even the open spots.
Edit: Found it thanks 
Yes

There is only one slot that is switched.

It's the spade to the left of the 50 amp circuit breaker.

Top right of this picture.

You have to use a spade connection to grab it and split it off from there.

Add an inline fuse and your good to go.e7eb2a7e74c3b41fd2cf50aea95b32e6.jpg

Sent from my SM-N960U using Tapatalk

  • Like 2
  • Thanks 1
tanner709 Enthusiast

tanner709

Posted
Posted
8 hours ago, Smoothbassman said:

Yes

There is only one slot that is switched.

It's the spade to the left of the 50 amp circuit breaker.

Top right of this picture.

You have to use a spade connection to grab it and split it off from there.

Add an inline fuse and your good to go.e7eb2a7e74c3b41fd2cf50aea95b32e6.jpg

Sent from my SM-N960U using Tapatalk
 

what triggers this on/off? or is this just a constant 12v w/ ignition on?

Smoothbassman Enthusiast

Smoothbassman

Posted
Posted

It's accessory power. 

 

When the ignition is in Accessory mode or running that pin is powered.

 

 

5 hours ago, tanner709 said:

what triggers this on/off? or is this just a constant 12v w/ ignition on?

 

  • Like 1
  • Thanks 1
tanner709 Enthusiast

tanner709

Posted
Posted
26 minutes ago, Smoothbassman said:

It's accessory power. 

 

When the ignition is in Accessory mode or running that pin is powered.

 

 

 

thank you sir

Zeker Enthusiast

Zeker

Posted
Posted
On 9/19/2019 at 11:08 AM, Smoothbassman said:

It's accessory power. 

 

When the ignition is in Accessory mode or running that pin is powered.

 

 

 

Did you by chance stumble on the dome light fuse? I ideally wanted power only when the dome lights are on.

Smoothbassman Enthusiast

Smoothbassman

Posted
Posted
Did you by chance stumble on the dome light fuse? I ideally wanted power only when the dome lights are on.
Pin 10 on the forward most BCM Connector.  2nd Gray wire.

It's also in the passenger side A Pillar from what I have been told, but I haven't had time to tear into it quite yet. That's Saturday mornings plan before I head to the muffler shop to get some more bottom end on this truck.

Sent from my SM-N960U1 using Tapatalk

Zeker Enthusiast

Zeker

Posted
Posted
3 hours ago, Smoothbassman said:

Pin 10 on the forward most BCM Connector.  2nd Gray wire.

It's also in the passenger side A Pillar from what I have been told, but I haven't had time to tear into it quite yet. That's Saturday mornings plan before I head to the muffler shop to get some more bottom end on this truck.

Sent from my SM-N960U1 using Tapatalk
 

Sorry.... I just realized you posted that before. Been a long week!

 

I not sure where to look for the BCM connector, can you help me out?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,938
    Total Members
    8,960
    Most Online
    C. Hart
    Newest Member
    C. Hart
    Joined

  • Who's Online   3 Members, 0 Anonymous, 551 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      287,500 Mile Service   8/13/2026   Reset Fuel Trims   Since the work done in the previous post there was a good improvement in response in all areas except right after a fill up where the LTFT would go -20%+ for about four miles while the STFT was near neutral. Before the work they both went very negative for a few miles after a fill up but act normal thereafter.    We did a systems check of the vapor recovery system for functionality and ability to hold a vacuum. That checked out fine. But this doesn't mean the charcoal canister is dead in the water. Testing that is next up. For now the reset of the fuel trims.    I intentionally shorted the fill exactly two gallons to eliminate any chance of filling the canister. On start up the trims were behaving normally until I got up and rolling where the LTFT went -10 / -11%% but the short was + 2 to 0%. Within a mile the the STFT offset the LTFT and by 2 miles they were neutral. HUGE improvement but still not hunky-dory.    I'll watch them for a few days. Perhaps another tank where I will fill completely to 'first click' and compare. Meanwhile on the hunt for a new canister and I'll toss another purge value at it for good measure. Pending the outcome of the canister test that is. Progress of any kind is welcome.    Fuel economy improvement with bringing hole #3 back to the living was a noticeable bump to the positive. Even on the few miles I drove after the refill I already see another bump up by the trims reset.     She's purring like a kitten with a warm bowl of milk.    BTW, adding 50 rpm to the idle took the majority of the negative timing out on cold start up and leaned the cold idle. No longer burbles in the cat. What a dumb way to heat a cat.      
    • OnTheReel
      Post your UOA, (used oil analysis) here

      By OnTheReel · Posted

      Yeah, shame I can’t really get that filter easily anymore. Running a PureOne. Your fave!    TAN would be neat to see. Confirmation I ran it too long probably. 🤣
    • superdave160
      Roll up bed cover experiences

      By superdave160 · Posted

      My son and I both bought new trucks in 2017. Both of us immediately put Truck Covers USA American Roll Covers on our trucks. My son still has his truck and it never sees the inside of a garage. We live in Alabama, so not much snow. My truck was my daily driver and was in the garage when I wasn't driving it or at work. No issues with either cover even after almost 9 years. About a year ago I sold my truck to my brother and bought a 2025 Silverado 2500. The second thing that I put on that truck was a new Truck Covers USA cover. They are very well made and have a very positive locking system. I looked at a Retrax and my concern was the way that the cover locked to the rail. BTW, the first thing I put on the new truck was step bars. Those new trucks are high!
    • superdave160
      Gasser Subforum Has Been Quiet - - So, Regenerative Braking and Using L10

      By superdave160 · Posted

      The Allison 10 speed torque converter doesn't "lock up" like the previous transmissions. It has 4 operational modes; open, slip, transition from open to slip; transition from slip to open. I have an Edge CTS3 monitor and I monitor transmission torque converter slip. Step on the gas and you get a little slip. Take your foot off the gas and you get a little negative slip. I have not found a way to display the torque converter mode beyond that. My Edge CTS3 also displays something that our trucks should already display, the current gear. I also monitor throttle body position and engine load. If I see the engine load getting too high, I'll manually drop a gear.
    • Grumpy Bear
      Post your UOA, (used oil analysis) here

      By Grumpy Bear · Posted

      Nice result. Your filter is working well  I'd have like to have seen the acid number for this sample. Curious type that I am. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...