Jump to content

Recommended Posts

Posted

This winter the alarm started going off after a remote start cycle ends.  When the car shuts off (after remote start cycle ends) there will be about a 30 second delay and then the alarm starts going off.  I mentioned it to the dealer service and they suggested trying a different FOB before they started digging into it. They obviously had not heard of the problem before. I tried a different FOB and it made no difference.  I have searched the internet and haven't seen anyone else mention this problem.  I don't have a lot of faith in the service at the dealer, so I am wondering if anyone has any ideas?

  • 7 months later...
  • 1 month later...
Posted

I have a 2019 Yukon Denali, and it’s horn starts honking for no reason. Tonight In was standing next to my truck with the door closed, key in my hand and fob hanging from the key ring, for no reason at all, the horn started blaring. Not honk honk honk, but just constant. Wouldn’t stop with me pushing buttons on the remote fob, I had to unlock the door and start it. I left the engine on and Door open as I talked to my employee, and the engine shut off, and horn started blaring again. I had to restart it to get it to stop. The other day it did the same thing but it also would honk when I turned the wheel with the engine and moving forward. It didn’t do it since Sunday so I figured it was  a random issue, but after tonight, I’m going to dealer in morning and letting them sort it out.. trust me if they say they can’t duplicate the problem, I’m not picking the truck back up. 

  • 2 months later...
Posted

Alright guys.. problem solved. rear defroster plug wasnt making connection. its part of the alarm system as if someone broke your rear glass.

so anyone having this issue its to do with one of the defroster tabs falling off which is pretty common, fix it and the alarm issue goes away.. i just did it and over 50 remote starts with the issue and now its gone!

  • 10 months later...
Posted

My 2015 tahoe just started doing this... Low and behold I looked at my rear defrost wire and it's dangling....thank you everyone. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • My truck is a ¾ ton but my placard also says 80 for the rear tires, I think I might have the upgraded suspension to the 3500 series maybe.   I put my air down to 60 and the light was still on, and there was no way I was putting over 60 psi in the rear empty and not towing because I knew the actual number Toyo gave me and I didn't wanna ruin the center of my tires!   And you actually can change it in the settings from metric or is and it will show kph or mph then when you go into your tire settings it will be either psi or kpa, but it would be nice to just change it directly on the tire psi page 
    • Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...