Jump to content

Won't start ?

B.R.67

By B.R.67
in Troubleshooting, Warranty & Recalls

 Share

Recommended Posts

Conecraft New Member

Conecraft

Posted
Posted

Took truck in to the Chevy dealer .. Code P12A6 came through on the scan. This is a fuel pump driver fault code. The dealer found Bulletin #20-NA-218 which addressed the spin but no fire problem and instructed to reprogram the ECN. As I read the bulletin & code P12A6.. I believe this bulletin address' the problem. We shall see, but I have confidence that the issue is resolved. 

  • 6 months later...
  • Replies 243
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

tystaples
tystaples

I have the same issue, started yesterday on my 2020 Denali 1500 with the 6.2. I purchased the truck new the end of April and it currently has 4900 miles on it. Crank and crank with no start. I did eve

tbarn
tbarn

A video of it not starting is of no use to the dealer or GM. It's not that they don't believe you but they cannot duplicate the concern. Watching it not start isn't any help diagnosing the issue.

econometrics
econometrics

True, but if you have a video with indisputable proof that the error is occurring, it will at least leverage them to take you more seriously and give more time to do tests needed to try and replicate

Posted Images

JonoLainez New Member

JonoLainez

Posted
Posted

I have a 2015 Silverado with the code P12A6. I have had the ECM changed the fuel module changed and the fuel pump changed even have had a ground rewired. All just to land on the truck leaving me stranded which is weird because in the morning it works just fine on the way home from work is when it turns off on me. I cannot find any resolutions to this problem has anyone figured this out? This is the weirdest code I have ever seen and when it leaves me stranded i can wait a little bit and then it cranks back up just enough for me to be able to pull it over to the side so i can leave it for a couple hours and come back to get it to take it home.

  • 5 months later...
Briggs Hollow New Member

Briggs Hollow

Posted
Posted
On 12/23/2019 at 1:51 PM, Icefisher said:

I am embarrassed to report my issue was operator error.

When I was washing my truck, I cleaned the Weather-Tech Floor mats.  When I reinstalled them, I accidentally covered the accelerator pedal.  By doing this, the vehicle will turn over but will not fire.

 

I didn't feel too bad, because it took the tech 5hrs to find the issue as well.  My dealer was really cool, and did not charge me a dime for the issue.

Thanks so much for your post! I tried a new fuel control module, which didn't fix it, and was just getting ready to have it towed when I read your post. Just cleaned my truck right before this happened and unknowingly covered the gas pedal. Debating on letting my wife know or not. Thanks again!!!

  • 1 year later...
Steve in MO New Member

Steve in MO

Posted
Posted

I just had the same issue described above, washed my floormats, replaced them, (accidentally put my floor mat over the gas pedal and didn’t know it) and then tried to start the truck.  Turned over but wouldn’t start.  Thanks for posting this, saved me a lot of headaches and time.  Put the floor mat in correctly, and it started right up.  2019 GMC Sierra 1500.  Your post is appreciated!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,962
    Total Members
    8,960
    Most Online
    contrabombarde
    Newest Member
    contrabombarde
    Joined

  • Who's Online   3 Members, 0 Anonymous, 1,336 Guests (See full list)

  • Latest Articles

  • Posts

    • richard wysong
      Needing this part.

      By richard wysong · Posted

      Still looks like a rivet to me in the pics, I don't see a nut and none of the pics show the head of the screw. But if you says so.....
    • jgaudet99
      Tire psi

      By jgaudet99 · Posted

      Thanks for all the help so far!   I did try right from 2026 right down to 2021, and only from 2023 down lets me select the option for tire psi change, but I get the vehicle not supported error!   I'll definitely try it under Chevrolet after work today, and I'll get the sensor number from gm for my truck tire sensors. And I'll let you know if it works for me under Chevrolet!   And if that doesn't work, I'm going to guess that what @Atlas said about maybe I have a different body control module could be true!  
    • Jsdirt
      2010 Avalanche 5.3 not running correctly after engine swap.

      By Jsdirt · Posted

      From where I'm sitting this sounds like a compatibility problem. I'm assuming the 2007 was a 900-series truck, and not an 800-series (they were sold side-by-side in dealerships that model year), since it starts and runs.   This is why I HATE post-2006 vehicles. Everything becomes a huge problem when you try to keep the thing running for longer than the manufacturer has designed it to.    I can't remember when Global-A architecture started - either '10 or '11. For your sake, you had better hope it's '11, or you're going to be spending some BIG money to correct this cluster-eff. That's something you need to find out before doing anything else. You may have several computers bricked ... but the fact that it runs tells me you MIGHT be ok here.     EDIT: Just did a quick refresher. You're screwed. This is Global-A. The 2 systems are NOT compatible in the slightest. Once you get the correct engine in there that IS compatible, you're going to need to see how many computers are locked. Absolute NIGHTMARE to straighten out, too. Your buddy might be better off cutting his losses and finding something else.   Welcome to post-2006 vehicle electronics. This is why I quit the industry, and drive nothing built after 1994. This stuff takes all the fun out of wrenching!  
    • bwiese
      Show Us Your 2019 & Up T1 Pictures !

      By bwiese · Posted

      Recently acquired new 2026 Silv. 1500 WT  - L3B + 4WD,  std cab + std bed, in (duh!) Sierra White. Upgrades: replaced 'steelies' w/  Vision "Flow" black alloys,  17x8.5"; HDX nerf bar w/steps (black powdercoat); Weatherguard large/deep alloy saddle toolbox; Michelin fitted bedmat (sale, perfect fit) Weathertech door sill guards TBD: rear wheebox liners 4x black fender arch trim - searching for best  (Putco: chrome only; not looking for flares either!) -Bill    
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      True, hard to say what differences there may or may not be between Chev and GM as well as a production year or mid year part change either.    I just found it odd that under the Sierra choice on the Autel that many of the last few years of production year did not include the choice of changing the tire pressure but if that is an Autel thing or a GM thing as to why the choices were not there. Knowing what tpms sensors are on the truck should give some guidance into which choices on the tool even make sense to try as I wouldn't give up just yet with the tool but I guess he will see what if anything he comes up with if he finds out a bit more info and tries a few more things on the Autel. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...