Jump to content

Engine swap no start

RatdogZ7
 Share

Recommended Posts

RatdogZ7 New Member

RatdogZ7

Posted
Posted

Hi all,
Installed remanufactured 5.3
Replaced oil, cam, crankshaft, Map sensors.
Went to start,
All electric works including fuel pump.
Theft deterrent light comes on and goes off with other start up lights on dash.
Turn key to start/crank, cranks for three seconds and starter stops.
Does not fire or start.
Code reader shows no fault codes.
I have not checked for spark yet.

I believe I hooked up all grounds but two of the 18ga (?) wires are missing about an inch of insulation and are loosely wound at connection.
Any suggestions?
Thanks

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

Gotta check for spark and fuel at the fuel rail.

 

See if it runs on brake cleaner or starting fluid.

Sharpz Enthusiast

Sharpz

Posted
Posted

even if your truck doesnt have spark or fuel you should still be able to crank it for more then 3 seconds. it sounds like you have a possible loose ground or wire that isnt getting good connection, and heating up when in crank mode making poor contact but then cools and allows it to get enough contact to crank again. I would fix getting it to crank for as long as I wanted first, then move on. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • DaleB
      No Software Updates - Old Build

      By DaleB · Posted

      Thanks, all. It sounds like keeping the software "as is" is the best course of action.
    • Grumpy Bear
      The Peckish Synapse

      By Grumpy Bear · Posted

      https://en.wikipedia.org/wiki/Overengineering   Excerpt from the above link: (BTW the above is a 90 second read)   [Quote]   A story about very precise engineering is given in the 1858 story The Deacon's Masterpiece or, the Wonderful "One-hoss Shay": A Logical Story by Oliver Wendell Holmes Sr., which tells of a carriage (one-horse shay) Because it had been engineered so that no single piece failed first – no piece was over-engineered relative to the others, and they thus all collapsed at the same time. A similar quote by Ferdinand Porsche claimed "the perfect race car crosses the finish line in first place and immediately falls into pieces."[5]   [End Quote}   By Engineering's  own definition then; the AFM and Torque Converters, 4-5-6 clutch assembly of the 6L80E, and a dozen other common chronic parts and systems failures are "UNDER ENGINEERED". And by their own definition done so with INTENT. Ya can't have it both ways OEM's.     
    • Spendit
      Installing tow mirrors

      By Spendit · Posted

      Everything you need to know..... https://www.gm-trucks.com/forums/topic/198157-2014-2017-dl8-dl3-towing-mirror-upgrade-–-mirrors-explained/
    • Gangly
      Broke Down on the Mountain

      By Gangly · Posted

      I was in Utah this week attempting a bow hunt in the Wasatch mountains with friends.  On the evening of the first hunt, making my way across a ridge to a friends camp, the upper control arm on the driver's side separated, the CV axle got trashed, and the wheel was dang near at a 45 degree angle to the ground.  I was able to get it towed off the mountain and into town about 3:00 am, and spent the remainder of the night in an O'Reilly's parking lot.  Luckily, there was a Chevrolet dealership not to far away so I was able to get to the dealership and pick up a new CV and UCA.  It would have been a few days before they could have gotten to the truck and I brought tools with me on hunt since it was a two day drive to get there, so I did the repairs myself in the O'Reilly's parking lot.      What's interesting is that the UCA ball joint didn't break, it just popped out of the bottom of the UCA.  There was VERY LITTLE evidence of grease on the ball joint or in the socket, and you could see where the ball joint had warbled out part of the socket over time.  I guess that's what happens over 186K miles of use :)   Big Kudos to O'Reilly's for letting me work on the truck in their parking lot.  However, they made a $150+ off of me from the purchase of various tools, so I guess it was in their best interest anyways :)   Getting towed off the mountain.   UCA Ball Joint Socket   Trashed CV   Suspension disconnected and UCA and CV Removed   New UCA and CV installed with the suspension buttoned up.    
    • KARNUT
      What did you do to your "other" car (aka musclecar) today

      By KARNUT · Posted

      My family still laughs at me when they see me drive up in the minivan. Same with less than a V-8 truck. It helps that I have choices. I don’t think I could only have a minivan as the one and only vehicle as much as I like it. And I wouldn’t pass up a good buy on an older V-8 reg cab GM truck. Could you live Raven as the only ride?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...