Jump to content

VIN # released

crf450r
 Share

Recommended Posts

crf450r Enthusiast

crf450r

Posted
Posted

I am new the forum,  Just ordered a 2021 2500hd,  it has been 18 years since I have ordered a vehicle, I am aware of the delays, but I wanted to know when the VIN# is provided during the process?  I want to put a topper on, and the lead time for that is 4-6 weeks.

 

Thanks

T.O. Enthusiast

T.O.

Posted
Posted

My dealer was able to get my VIN number immediately after it's production week. I am almost certain it hadn't even left the plant on the railcar yet and he had mine. There is a thread on here describing the process with all the 4 digit numbers, but I am not sure what number is associated with the VIN.  

newdude Senior Enthusiast

newdude

Posted
Posted

You won't get a VIN until 3800.

 

Quote

 

• 500, this is a dealer stock order code used to order common vehicles. Please contact your dealer to receive an actual active order number.
• 1100, Preliminary order accepted (This means your dealer has entered your order into their system but does not mean they have the allocation to submit the order to GM yet. Speak with your dealer to verify when they expect to be able to submit your order for production)
• 2000, Order accepted by GM (This means the order has been submitted and accepted by production. You are now on your way.)
• 2030, Order re-edited (if necessary) (This is simply an edit code showing that something on your order has been changed. It does not mean your order has been accepted to production and really does not mean anything beyond your previous status other than a change has been made.)
• 2051, Order changed thru Web (same as above)
• 2500, Order preferenced (This means that the Order has been moved to the stage that parts department is now ready to place the orders for the components that will become your car)
• 3000, Order accepted by production control (This is the response from production to your 2500 status and is when Parts are actually ordered. No further changes can be made to your order once you reach this point.)
• 3100, Order available to sequence (This is more or less an inter-office memo from Parts to Production saying all parts are committed to this build, they are clear to sequence them for the build.)
• 3300, Order scheduled for production (This is the response to the 3100 status where Production is cleared to sequence and schedule the build) TPW usually avaiable
• 3400, Order broadcast (This is when the order is actually loaded onto the production line computers and parts are being staged for the build)
• 3800, Order produced (The vehicle is completed and has rolled off the line. A Vin is now available.)
• 4000, Available to ship (Vehicle is off the line and available to ship)
• 4104, Bailment Invoice (Shipping documents generated)
• 4200, Shipped (Vehicle has been moved by a carrier to another location or destination. If in combination with a 4300 status code then this is transfer to either a vendor for upfitting or to a distribution yard for final transportation.)
• 4300, Intermediate Delivery (In combination with a 4200 this is saying that the vehicle has been transported to a vendor or to a distribution center.)
• 4B00, Bayed (listed anytime a vehicle is sitting parked waiting for next mode of transportation. It can also be this status while in Quality Control)
• 4800 Rail Ramp Unload, end of the line by (if) rail. To be delivered by truck to dealer
• 5000, Delivered to the dealer
• 6000, Delivered to the customer
• 9000, Order Cancelled

 

 

  • Like 2
nards444 Senior Enthusiast

nards444

Posted
Posted

yeah have to know where you are at in the process.  3800 is when you get a vin and for the most part truck should be done.  With that said to get to 3800 for some takes weeks or months.  Once you get to 3800 you can figure about a month to get the truck.

Another JR Senior Enthusiast

Another JR

Posted
Posted (edited)

I was at 3800 with a VIN on 3/8.  My dealer just gave me an ETA of 4/26.  I think the fact that they now have an ETA means it finally actually went to the outgoing shipper after a couple of weeks of moving around Flint.  

Edited by Another JR
TheeSpaniard3500hd Enthusiast

TheeSpaniard3500hd

Posted
Posted

My truck has an eta of 4/28 per the train shipping data page. Truck arrived in Portland on the way to Seattle area on Sunday. It doesn’t seem like it should take a month to delivery when it’s that close. Hoping it arrives sooner. Dealer has been sending almost daily updates of transit progress which I appreciate.


Sent from my iPhone using Tapatalk

Z45 Senior Enthusiast

Z45

Posted
Posted (edited)
6 hours ago, TheeSpaniard3500hd said:

My truck has an eta of 4/28 per the train shipping data page. Truck arrived in Portland on the way to Seattle area on Sunday. It doesn’t seem like it should take a month to delivery when it’s that close. Hoping it arrives sooner. Dealer has been sending almost daily updates of transit progress which I appreciate.


Sent from my iPhone using Tapatalk

Shipping companies are experiencing unprecedented demand,  transit delays and personnel shortages..  I been waiting for weeks to get a replacement door panel for my 16ft garage door and the local installer said its been taking months to get parts that used to take a week at most.    

Some things are just not important in the grand scheme of things and there is no priority to move them. That's just the way it is with the current state of affairs.  Vehicle movements are not high priority.

Edited by elcamino
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,914
    Total Members
    8,960
    Most Online
    AidenVorpagel
    Newest Member
    AidenVorpagel
    Joined

  • Who's Online   1 Member, 0 Anonymous, 1,056 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      286,740 Mile Services   8/6/2026   New AC Compressor. Refrigerant oil and dye, evacuate and charge system.  New exhaust system from cat back.  New Iridium plugs plus replace #3 coil Repair/rewire headlamp wiring (passenger side) and replace all forward bulbs. Polish lenses of both assemblies.  Pull rear rotors, clean and adjust parking assembly. Inspect, clean and grease front calipers. Check pads and shoes.  4 wheel power bleed of brake system. Dot 4 Reset idle speed 50 rpm higher New Serpentine belt.    Will need new pads in the rear in about 5K more miles.    Tax Title and License out the door just short of a grand.    AC clutch had bitten the dust. 1 year warranty on the pick and save replacement. Thing will make a Polar Bear cry Uncle.  He spent quite some time on the wiring. It was in the harness and he does nothing half. I got off cheap. I have considerable more light down the road. Sylvania Silver Star replacements.  Gas seal between the porcelain and shell of plug #3 was blown, cooked the coil. That was the cold miss.  Love the new exhaust. I can sneak into the neighborhood again.  Nice to have a working parking brake again. Belle Tire never got it done. That was disappointing.    This was one of her bigger bills and still way cheaper than a payment even given the oil consumption. This thing cost me under a hundred a month in repairs and normal routine costs. What is my incentive to replace it? 🤔           
    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  
    • B14Sierra
      Noise after AFM delete

      By B14Sierra · Posted

      Did you figure it out?
    • B14Sierra
      Possible lifter tick after DOD delete

      By B14Sierra · Posted

      Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...