Jump to content

Coolant Leak 2015 Sierra

SkiDooNick700
 Share

Recommended Posts

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
Posted

Hey guys,  2015 GMC Sierra 6.2 NHT April 2015 build. 

 

All of a sudden I've got a coolant leak but haven't been able to pinpoint where from.   I see the drivers side frame wet and will drip to the ground.   Coolant level already down up to 2 inches from Cold line.   It's even wet on the back side of the lower valence. Just noticed this leak after a 200-300 mile trip back from vacation.  

 

Dried up the frame,  took it on a 3 mile drive,  already dripping with coolant.

 

Any advice? I am not sure where else to look - might need to start pulling stuff off the truck to get a better view?

Is my truck build date part of the known TSB? Is it possible to see the stress cracks per the TSB without disassembling anything?

 

 

20210804_175635.jpg

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
55 minutes ago, Snowcamo said:

Bottom of the water pump usually has a weep hole. Try there. That's not to bad of a job if your mech inclined.

 

I will have to take a look to see if it is wet.   It didn't cross my mind to check it.  

 

50 minutes ago, CamGTP said:

$5 it's the radiator that needs to be replaced.

 

I am worried this may be the case lol.   There is like a tray or something running under the radiator and it is wet all along it from what I am able to see visually. 

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted (edited)
10 hours ago, CrawlSlow said:

I would start with the easy stuff first before taking things apart.. Drain plug, check along side of radiator to see if it's wet.

 

Thanks for the tips.  Is the drain on the passenger side? 

 

As far a checking the sides of the radiator,  I swear I've looked at every possible angle top and bottom left and right and I am not able to get a clear visual of the sides of radiator. 

 

I watched a video it seems like a pretty quick process to remove the top cover piece,  air box, and fans.   Thinking this might help my view out. 

Edited by SkiDooNick700
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted

Well guys looks wet at drivers side corner of radiator.   I'm thinking it is cracked somewhere?  Going to try to pressure test.

 

It was pretty easy to get the fans out the way,  just took me a while to figure out the clips and such.   I need to buy the right tool for the job lol. 

20210805_175819.jpg

  • Like 1
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
On 8/4/2021 at 8:06 PM, CamGTP said:

$5 it's the radiator that needs to be replaced.

 

You appear to be the winner!  Took some things apart including removing fan shroud.   Did a pressure test,  the drivers side corner of radiator is leaking.  It was a pool in no time. 

 

Now to find a new one,  looks like GM replaced with a new part number. 

  • Like 1
SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
4 hours ago, Gagliano7 said:

https://www.rockauto.com/en/catalog/chevrolet,2015,silverado+1500,5.3l+v8,3307665,cooling+system,radiator,2172

 

Thanks yep I used RockAuto to figure out the updated number.   Called a local "dealer" who has one in stock,  about 350$.  Had to purchase via their website to get that price otherwise they have to sell for 500+ in person. Something about GM e-commerce policy. 

  • Like 1
Ravenkeeper Senior Enthusiast

Ravenkeeper

Posted
Posted
On 8/4/2021 at 5:00 PM, Snowcamo said:

Bottom of the water pump usually has a weep hole. Try there. That's not to bad of a job if your mech inclined.

Usually when the water pump plug goes, it's a huge mess, and not driveable.   It will blow out all of your coolant.

 

On 8/6/2021 at 6:39 AM, SkiDooNick700 said:

 

Thanks yep I used RockAuto to figure out the updated number.   Called a local "dealer" who has one in stock,  about 350$.  Had to purchase via their website to get that price otherwise they have to sell for 500+ in person. Something about GM e-commerce policy. 

Cheaper than RA?

SkiDooNick700 Enthusiast

SkiDooNick700

Posted
  • Author
Posted
7 hours ago, Ravenkeeper said:

Usually when the water pump plug goes, it's a huge mess, and not driveable.   It will blow out all of your coolant.

 

Cheaper than RA?

 

Rock Auto has it for 335 plus $20 shipped.   It was more or less a wash.   At that point I said to myself let me get locally if I can instead of having a radiator potentially tossed around by UPS or FedEx.

 

Finished install of new one last night,  took on 20 minute test drive.  All seems good so far.   I need to do a good washing of the engine bay now, there is so much coolant still down the frame and such lol. 

 

I think I am going to order a new T Stat, my temp gage always fluctuated a tad but very very recently (last 100 miles)  it's doing some big swings, from 210 down a line and back up to almost 210.

 

Also my idle seemed kinda rough yesterday not sure what is up with that.  She's going through a phase!

  • Like 2
diyer2 Senior Enthusiast

diyer2

Posted
Posted

 instead of having a radiator potentially tossed around by UPS or FedEx.

 

They delivered the part you bought I bet. 

Z45 Senior Enthusiast

Z45

Posted
Posted (edited)

There was a service bulletin on leaks, had my 2015 repaired under warranty for leaks.  In short faulty thermostat cause radiator failure.

Quote

This condition may be the result of excessive thermocycles within the cooling system caused by excessive cycling of the thermostat. These excessive thermocycles within the coolant system may cause the tubes to fatigue, crack and leak at the radiator headers. To correct this condition, a new thermostat has been designed that eliminates the
thermostats excessive cycling.   If this condition is found, in addition to replacing the radiator, the engine coolant thermostat housing (w/thermostat) must also be replaced. Refer to Engine Coolant Thermostat Housing Replacement in SI, which is located in the Engine Heating and Cooling section.

 

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&ved=2ahUKEwiA-7iSyqvyAhUIVc0KHd6zACMQFnoECAYQAQ&url=https%3A%2F%2Fstatic.nhtsa.gov%2Fodi%2Ftsbs%2F2019%2FMC-10155058-9999.pdf&usg=AOvVaw2ifEl9-OC04g37-bj7JXC2

Edited by elcamino

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,965
    Total Members
    8,960
    Most Online
    DaleB
    Newest Member
    DaleB
    Joined

  • Who's Online   2 Members, 0 Anonymous, 1,335 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Common Sense Assembly   Your driveline is forgiving of the occasional mistake. It will even often forgive the random serious blunder. But it will not forgive a continuous bad habit.      What? Not everything needs to be a five thousand word essay.       
    • Grumpy Bear
      Gas Prices

      By Grumpy Bear · Posted

      We drove about 15 minute east today to visit a friend and saw a steep increase in price in the same county. About 50 cents a gallon steepper. 
    • Grumpy Bear
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Grumpy Bear · Posted

      Sure about that? A degree wheel and a dial indicator would lower your degree of assurance in that statement. 😉    It why we have offset keys and dialable timing sprockets. Just say'n.... I've built a few and have never seen one "On the money". 
    • Chuck FB
      Tire psi

      By Chuck FB · Posted

      I will admit I haven't experimented much with pressure drops beyond the numbers I put in and part of that is that the numbers I used are fairly low and then found out it would trigger regardless at that 35 psi. Having said that I had tried before had changed the placard pressures and being that I have a 1 ton set to 80 on the placard for the rear I believe it triggered close to 60, the front I don't recall now for sure but thought maybe it could get close to 45 from that factory 60 placard pressure. So I never did figure out if it was a number of psi from placard pressure to the alarm or a percentage of the total placard number as some figured it was like a 25% drop from placard pressure would trigger it. So as to try and answer your question, I believe I set the placard pressure on the front to 47 or so and while I run the front tires at 40, they have dipped below that some if its colder and I haven't put "winter air" in yet and never once have had the front alarm go off. I would say that the answer your looking for is no, that if you set your placard pressure to 45, you have a certain amount of room to drop below that pressure before the alarm will go off.    The pressures you decide to run in your truck, that ends up being what makes sense to you based on what your carrying in your truck or if towing, then have to bump them back up to something that will carry the load in the rear and the fronts typically left at the same pressure. It all comes down to that chart I put the link to and using an accurate roadside scale to be your guide, both unloaded and then loaded to know your minimum safe pressures.    I just wish GM would allow a person to change the readings for the tire pressures to the English system of pounds as I have to look at that goofy metric reading that will never ever jive in my head and will go over and change it just to figure out what they are if need be and then change it back. 
    • TrueBlue
      No Software Updates - Old Build

      By TrueBlue · Posted

      That part I understand, that the dealer can do it. But I'm not understanding why updates that were available to the truck since it left the factory, or the dealership originally, would not still be available to it without dealer intervention.   I'm thinking along the lines of recalls. They stay available until they are completed, regardless of whether they are in warranty or not, or in the hands of the original owner or not. Why not updates as well, especially since some of those can be safety related also?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...