Jump to content

Shaking

Ryno1985
 Share

Recommended Posts

Ryno1985 New Member

Ryno1985

Posted
Posted

2011 silverado 1500 Short story  going down the highway heard a clunk there goes my tire with the bearing and caliper on it cv axle broke with it 

I replaced cv axles struts bearings calipers rotors and pads  both sides on the front along with new tires 

When I start the truck i have no lights on the dash  soon as I move the triangle  traction light comes on  and service stabilitrack  it seems fine going slow but when I take it  down the road and slow down from 60 it shakes really bad  pretty sure I have it bleed good it's got a good firm pedal  any ideas what would cause the shaking and the light to come on 

Sharpz Enthusiast

Sharpz

Posted
Posted
7 hours ago, Ryno1985 said:

2011 silverado 1500 Short story  going down the highway heard a clunk there goes my tire with the bearing and caliper on it cv axle broke with it 

I replaced cv axles struts bearings calipers rotors and pads  both sides on the front along with new tires 

When I start the truck i have no lights on the dash  soon as I move the triangle  traction light comes on  and service stabilitrack  it seems fine going slow but when I take it  down the road and slow down from 60 it shakes really bad  pretty sure I have it bleed good it's got a good firm pedal  any ideas what would cause the shaking and the light to come on 

might be your U-joints are bad to cause the shaking.  Be sure you didnt damage any wires when your suspension dropped out. 

Brian715 Enthusiast

Brian715

Posted
Posted

What bearings did you use? I've seen the Autozone(cheapies) throw that code right away due to faulty abs sensors in the hub. 

Ryno1985 New Member

Ryno1985

Posted
  • Author
Posted
6 minutes ago, Brian715 said:

What bearings did you use? I've seen the Autozone(cheapies) throw that code right away due to faulty abs sensors in the hub. 

They were trq bearings not expensive but not the cheapest I could find either 

Ryno1985 New Member

Ryno1985

Posted
  • Author
Posted
2 hours ago, It's Tim said:

Was it possible to align the truck to specs?

I'm gonna get an alignment done Friday see if that takes care of it 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Black02Silverado
      Post your UOA, (used oil analysis) here

      By Black02Silverado · Posted

      Here's the second UOA on my 22 Wrangler with the Ecodiesel. This has 5k miles on AMSOIL Signature Series DEO 5w-40. The first one was dealer installed oil, no clue what it was, the second is what AMSOIL recommended, European FS 5w-40, Most of the Ecodiesel world is showing great results using the European MS 5w-40, I figured I would see how the DEO works. This is using an Ecoguard oil filter. It's my understanding this engine likes to shed aluminum.  We will see. So far I don't think this is too bad.    
    • revmanii
      Disable DRL's

      By revmanii · Posted

      I'm surprised nobody seems to offer a solution like the start/stop device I put in my new truck. Remembers my setting when shutdown. And while it still starts up in start/stop, it stores/evaluates what mode it was in when shut down and will change it whithin a second or 2 of startup. It'd be nice to have something like that for the DRLs.
    • btm
      Sunroof Drain Hole Entry & Exit Location (w/ Pictures)

      By btm · Posted

      2015 Sierra 1500 here. Leaks from the sunroof to front driver side and soaks carpet. How do I fix this? Thanks!
    • Atlas
      Wow I'm in a pickle. (Broke down truck) and a story.

      By Atlas · Posted

      I will be doing that for sure, but I need to solve who has/ where I can find a bidirectional scan tool that will support OBD 1.5. I'm kicking myself because I ebay'ed a Snap On MT2500 that I didn't think I'd ever need anymore. D'oh!! I'd rather not buy another, so I'll contact a few local shops to see if they have one and how much they'd want to do the procedure. I'd rather have the ability to do it myself... I wish there was a modern tool that could do it all, but I'd have no idea what to buy.   The theory with the pulled timing is that it mimics a rich condition. The delayed spark causes incomplete burn and the O2 sensor picks up low oxygen levels. That's interpreted as a rich condition so the PCM pulls fuel and that shows up in the deeply negative fuel trims.
    • Chuck FB
      Joke Thread

      By Chuck FB · Posted

      An ultra wealthy man had the most beautiful daughter. But, there was a problem. Everything she touched would melt in her hands. No matter what, Metal, Wood, Stone. Anything she touched would melt. She could not feed herself. Because of this, men were afraid of her. Nobody would dare marry her. Her father was despaired. What could he do to help his daughter? He consulted doctors, scientists and anybody who could solve this problem. Finally one of them said, "If your daughter touches one thing that does not melt in her hands, she will be cured." He was overjoyed and came up with a plan. The next day, he held a competition. Any man who could bring his daughter an object that would not melt in her hands would be given billions of dollars to marry her. Three extremely intelligent and handsome young men took up the challenge. The first brought a very heavy steel rod, But alas, when the she touched it, it completely melted in a matter of seconds. He sadly went away. The second brought a beautiful diamond, knowing diamonds were one of the hardest substance in the world and would not melt. But alas, once she held it in her hand, it melted. He too was sent away disappointed. So now, there was one left He was very nervous & sweating. He approached the daughter & said, “put your hand in my pants pocket and feel what is in there." She did exactly what he asked. She felt something very hard. She held it in her hand, squeezing it as hard as she could. It did not melt & remained extremely hard. Her father was overjoyed. Everybody was overjoyed. She was finally cured. Nothing never, ever melted in her hand again. They married and they both lived happily ever after, raising a wonderful family. Question: What was in the the groom’s pants pocket??? Answer below ↓ M&Ms of course! They melt in your mouth, not in your hand. What on earth were you thinking?

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...