Jump to content

TPMS Issue

2642HDfxd
 Share

Recommended Posts

2642HDfxd Enthusiast

2642HDfxd

Posted
Posted

The TPMS warning light on my 2015 Silverado lit up and the panel indicates the left front tire is low. It shows a pressure of 28-29 pounds. Actual pressure is about 32-33. Did not change any tires and did not add air to any tire recently. I know nothing about these contraptions. Suggestions on where to start are appreciated. Thank you.

MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted (edited)
4 minutes ago, 2642HDfxd said:

The TPMS warning light on my 2015 Silverado lit up and the panel indicates the left front tire is low. It shows a pressure of 28-29 pounds. Actual pressure is about 32-33. Did not change any tires and did not add air to any tire recently. I know nothing about these contraptions. Suggestions on where to start are appreciated. Thank you.

Time to either get your TPMS re calibrated or replace the TPMS monitor at that wheel.

Edited by MikeBMW
CamGTP Senior Enthusiast

CamGTP

Posted
Posted (edited)

Put air in your tire and the light will go off. Your manual gauge could be wrong.

 

I have like 8 different tire pressure gauges, none of the slide style read exactly the same. Bridgestone used to send us boxes of like 200 at a time when I worked for that shop. I'd break them or they'd blow apart all the time. More often than not they are sorta accurate but that's good enough.

Edited by CamGTP
  • Like 1
mikeyk101 Senior Enthusiast

mikeyk101

Posted
Posted

When you check pressure in other tires, do they match on your hand held gauge? 

  • Like 1
2642HDfxd Enthusiast

2642HDfxd

Posted
  • Author
Posted

Aired all 4 tires up to 35 and disconnected battery. Warning TPMS light is now out, but only one tire shows pressure (31). The other 3 on my display are just "dashes". My screen also insists it is January 1 and 35 degrees. It's been in the 90s here for days!!! I ran it about 8 miles but perhaps it requires more calibration to set everything. Am on my second display as the other one gave up the ghost about 2 years ago. Was out of warranty but luckily GM picked up the tab after alot of complaining. Hope I don't have another issue. Appreciate the comments and help.

2015 High Miler Enthusiast

2015 High Miler

Posted
Posted

I would do the battery disconnect again, but also turn the key on when disconnected.  
 

youill have to rest your clock and drive 5-10 miles and your thermometer will readjust.  You may need to visit a tire shop or the dealer and see if they will rescan your tpms   Def sounds a little off. 

  • Like 1
2642HDfxd Enthusiast

2642HDfxd

Posted
  • Author
Posted

Thanks all. Everything working OK now except left front reading 28 psi and the others 31. I'm sure there is 35 in each one. Checked with my motorcycle tires which I keep real close and also a second gauge. Light is off which is the most important. Has anyone used the available on e bay tools which allow you to reset your TPMS?

  • Like 1
MikeBMW Senior Enthusiast

MikeBMW

Posted
Posted
10 hours ago, 2642HDfxd said:

Thanks all. Everything working OK now except left front reading 28 psi and the others 31. I'm sure there is 35 in each one. Checked with my motorcycle tires which I keep real close and also a second gauge. Light is off which is the most important. Has anyone used the available on e bay tools which allow you to reset your TPMS?

I bought the Autel TPMS TS508.
I suggest one stay away from the cheap ones, JMO...

  • Like 2
14LTZ-1LZ Enthusiast

14LTZ-1LZ

Posted
Posted

Bought this from Amazon for $19, works on my Silverado and Malibu.

 

VXSCAN TPMS Relearn Tool El50448 Auto Tire Pressure Monitor Sensor Reset OEC-T5 for GM Series Vehicle

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.

  • Forum Statistics

    250.5k
    Total Topics
    2.7m
    Total Posts

  • Member Statistics

    342,914
    Total Members
    8,960
    Most Online
    AidenVorpagel
    Newest Member
    AidenVorpagel
    Joined

  • Who's Online   4 Members, 0 Anonymous, 1,372 Guests (See full list)

  • Latest Articles

  • Posts

    • Grumpy Bear
      Sugar Bears 2015 GMC Terrain SLE-2 2.4 AWD

      By Grumpy Bear · Posted

      286,740 Mile Services   8/6/2026   New AC Compressor. Refrigerant oil and dye, evacuate and charge system.  New exhaust system from cat back.  New Iridium plugs plus replace #3 coil Repair/rewire headlamp wiring (passenger side) and replace all forward bulbs. Polish lenses of both assemblies.  Pull rear rotors, clean and adjust parking assembly. Inspect, clean and grease front calipers. Check pads and shoes.  4 wheel power bleed of brake system. Dot 4 Reset idle speed 50 rpm higher New Serpentine belt.    Will need new pads in the rear in about 5K more miles.    Tax Title and License out the door just short of a grand.    AC clutch had bitten the dust. 1 year warranty on the pick and save replacement. Thing will make a Polar Bear cry Uncle.  He spent quite some time on the wiring. It was in the harness and he does nothing half. I got off cheap. I have considerable more light down the road. Sylvania Silver Star replacements.  Gas seal between the porcelain and shell of plug #3 was blown, cooked the coil. That was the cold miss.  Love the new exhaust. I can sneak into the neighborhood again.  Nice to have a working parking brake again. Belle Tire never got it done. That was disappointing.    This was one of her bigger bills and still way cheaper than a payment even given the oil consumption. This thing cost me under a hundred a month in repairs and normal routine costs. What is my incentive to replace it? 🤔           
    • AidenVorpagel
      cam upgrade in CA

      By AidenVorpagel · Posted

      hello I recently bought a 2012 gmc 1500 with a 5.3 and have a AFM disabler on it I'm interested in doing a cam but I'm worried if I remove the AFM system I will fail smog does anyone have info if they are able to detect that or a work around to it (not talking about hot smogging) please let me know thank you  
    • B14Sierra
      Noise after AFM delete

      By B14Sierra · Posted

      Did you figure it out?
    • B14Sierra
      Possible lifter tick after DOD delete

      By B14Sierra · Posted

      Update. I started chasing down my symptoms. Started first with pulling valve covers and looked at everything. Everything looked good and couldn't hear or feel anything different. Then a compression test. 240 psi or really close on each cylinder. I was worried I was a tooth off of timing. Not bad for an engine with 173,000. Granted I did put new heads on. I sprayed water around the injector area to see if I could hear a change. Nothing. I hooked up my new hp tuner which I should have done in the first place but I don't really know what I'm looking at just yet but am learning. I noticed the fuel trims were way off so that told me I have to have either a bad injector or exhaust leak. New injectors, so I did the shop vac on blower and in the tail pipe. Sprayed soapy water and found the exhaust flange on the drivers side was leaking. I didn't think it would be that considereding I pulled the heads and left the manifolds attached. I did have the transmission replaced not long ago. They must have not seated them properly but I guess I didn't notice. I put in new gaskets on both sides. Which by the way isn't a bad job but I had a hard time getting them to seal right. Took two attempts. Reset the fuel trims and the ticking is gone, engine runs smooth and acceleration has improved. Got to feel the real difference with that stage 1 cam. It's not that big of a difference but it does add a little more. It feels like how the truck should have been from the factory.
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      Can it still be Assembled I?    Stribeck says that we need a certain amount of viscosity under conditions of load and velocity to prevent two surfaces of a know roughness from tearing each other asunder. And we have marketing trying to tell the masses that those two surfaced require less of that commodity due to more exact limits being placed on the same old clearances. We also know that there are limits to how hard something can before it becomes to brittle to be viable and to smooth to 'wet' the surface and that both of those conditions have been known and met since about the Second World War.    That viscosity value shook out at 10 centistokes at 212 F just under a hundred years ago.  Give this a look: [Anton Parr]     What is advertised is the Kinematic viscosity (mm2/s) or that which has been density adjusted but the value we are after is the dynamic viscosity (mPa.s) or true viscosity. You can see that this number is dependent on density thus base stock and temperature. You can also see that an SAE 30 doesn't reach that value in this example. However an SAE 30 that is at the upper end of the SAE 30 range; 12.5 cSt (mm2/s), might. 12.5 * .83 = 10.375 (mm2/s). If you could find an SAE 30 at the upper end these days.   Then there is the complication of viscosity modifiers or VII or VM, whatever you wish to call them. Polymers added to very thin base oils, perhaps 3 to 6 cP oils, that will meet the SAE *W30 spec at 'tested' shear rates and 100 C/212F  target temperature. So a polymer fortified base that is a fraction of the 10 cP requirement Stribeck insist upon.   This could be all well and good if those polymers didn't have two very problematic 'features'. They shear or loose viscosity both 1.) permanently and 2.) temporality. And they do both omitted in the advertised data with the distinct  purpose of deceiving the consumer of the actual operating state of the fluid. I've shown the example of Warren Oils COSTCO 10.91 cSt 5W30 formuation several times where the 100 C HTHS value is 6.9 cP!! That's the temporary shear down and with and SSI or shear stability index of 9.4 cSt. Note the intentional deception in using mixed units?    After a short while that 9.4 cSt oil has a viscosity corrected dynamic value of 7.8 cP. But as the SSI is still within the range of an SAE *W30 whose lower value is 9.3 cSt.    This allows them to continue to call this SAE 16 weight oil a 30 weight, the cake, and still meet the API requirements for fuel efficiency IMPROVEMENT mandated by the EPA. The eating of the cake. By the time you've worn out your motor doing the responsible thing by adhering to the warranty requirements, (the stick), you get deprived of the carrot, wear control. So sad, to bad.   So what can be done? Do I need actually say? [Anton Parr]       Even this must be monitored if the oil is on the low side and the VII an organic or you opt for a 0W40 with an even lighter base oil and more / higher MW VII. (Note the lower density of the 40 weight versus the SAE 30 mono-weight?)    There is another workaround. Temperature. An SAE *W30 run at a bulk temperature of between 180 and 195 F.    Being the belt and suspenders sort I am I do both. Run it cook and run it heavy.    In Part II I'll work the AW package. 

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...