Jump to content

What leveling kit?

Hello32

By Hello32
in Modifications, Wheels & Tires

 Share

Recommended Posts

Hello32 Enthusiast

Hello32

Posted
Posted

Ok So i have a 2021 sierra elevation crew cab. I am wanting to change the wheel set up. I love the look of 12" wide rims but don't want rubbing. So I was considering a 10" wide rim. What leveling kit do you guys recommend to preserve the factory ride? 

Gangly Senior Enthusiast

Gangly

Posted
Posted (edited)

 

6 hours ago, Hello32 said:

What leveling kit do you guys recommend to preserve the factory ride? 

There are a billion posts about this already and 5 minutes of searching would go a long way.

 

However, the bottom line for "just a level" is as follows:

If you want to do a spacer level, then brand is irrelevant and they all do the same thing.

If you want to do a suspension level, Bilstein and Eibach are quality setups that most people go with.

 

 

 

Edited by Gangly
Adam Shell New Member

Adam Shell

Posted
Posted (edited)

I have the same truck, and installed the factory leveling kit.  I gained two inches up front and it looks great.  I have the factory wheel set up, but put on 33x12.5 BFG MT KO3 Tires.  No rub, great look, factory ride... hope that helps

IMG_7086.JPG

IMG_7087.JPG

Edited by Adam Shell
added pics
andrewb24 Enthusiast

andrewb24

Posted
Posted

I installed Motofab 2.5" upper leveling kit my self and also added a 1" block in the back.  If you do consider doing your self be very careful with cv axles to not stretch and rip boots also get an alignment done after.

  • 2 weeks later...
EpisodicDoleWhip Enthusiast

EpisodicDoleWhip

Posted
Posted

Probably not what you want to hear, but I wouldn't install one.  They look good, but they all compromise the ride, they make it hard to get perfectly aligned, and I've experienced issues with the truck eating ball joints since the install.

 

Granted, that was all on my 2015 Silverado, not my 2020 Sierra, but still...

Stiffler Enthusiast

Stiffler

Posted
Posted
On 9/17/2021 at 10:00 AM, andrewb24 said:

I installed Motofab 2.5" upper leveling kit my self and also added a 1" block in the back.  If you do consider doing your self be very careful with cv axles to not stretch and rip boots also get an alignment done after.

Where did you get the 1 in block from?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.
    • SoCal Angler
      Parking Brake - Automatic Engagement Questions

      By SoCal Angler · Posted

      2023 GMC 3500 HD, SLE, 6.6L Gas, 4x4, 6 Spd Options:  SLE Convenience Package; Driver Alert Package 1; Spray on Bedliner; X31 Off Road Package; TRAILERING MIRRORS, HEATED POWER -ADJUSTABLE, AUTO DIMMING, WITH TURN INDICATORS WHEELHOUSE LINERS, REAR INC. REAR AXLE - 3.73 RATIO INC. GVWR, 11,350 LBS. (5148 KG) INC. FRONT AND REAR PARK ASSIST, INC. ULTRASONIC     I have been launching my new boat and noticed some things related to the parking brake.. I usually set the parking brake (habit) when on flat ground for typical driving.    When backed down on the launch ramp to launch the boat and I place gear selector into Park, the parking brake activates automatically. My second nature is to set parking brake manually and noticed I was turing the parking brake off.  The parking brake appears to be setting itself automatically.   I looked all over my owner's manual and only found references to being on an incline and manually setting parking brake, or at times parking brake will be auto engaged, but nothing specific to my situation.    When is the parking brake automatically engaged?  Under what specific circumstances?  Can the auto set parameters be changed?     I like the auto set feature.  It would be nice if always engaged when shifted into Park and released when shifted out of Park (like my wifes 2025 RAV4).   Thanks!    

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...