Jump to content

Running rough

Joel godard
 Share

Recommended Posts

Joel godard Enthusiast

Joel godard

Posted
Posted

Had dreaded lifter tick. Replaced all lifters. New head gaskets, intake gaskets , coils, wires, plugs. Adjusted rockers to 22 ft. Lbs. By the manual. Torqued heads by the book. Using torque angle gauge.  Got it together. Runs rough. Any ideas?

Sharpz Enthusiast

Sharpz

Posted
Posted

are you throwing any codes?  Have you drove it at all?  A few suggestions is check your plugs for fouling.  Doing the front easy to get to ones will be good enough to check.  Also make sure all of your injectors are seated straight and plugged in. 

sspeedguy Enthusiast

sspeedguy

Posted
Posted

Does it idle ok then run rough under throttle? Cuz that what mine has started doing after a very similar rebuild, except mine was driving for around 1000 miles before it started this and also i fitted a new stg 1 cam at the rebuild.

Joel godard Enthusiast

Joel godard

Posted
  • Author
Posted

Have pulled valve covers since.It runs good for a second at start up then starts running bad. With valve covers off. #1, 4, and 6 rockers aren't moving. They move when I'm turning over by hand. It's a new vlom.?????

Joel godard Enthusiast

Joel godard

Posted
  • Author
Posted

It ran good before. Just had the lifter noise. It was only one lifter on #1 cylinder that failed. I've done mechanic work for 25 years until my health failed. But haven't worked on this particular problem. Have worked mostly on 60's-90's cars and trucks.

CamGTP Senior Enthusiast

CamGTP

Posted
Posted

If it's only the AFM cylinders then it's likely the lifters again. If the rockers don't move at all then the lifters are stuck.

  • 1 month later...
Joel godard Enthusiast

Joel godard

Posted
  • Author
Posted

Update! Fixed that problem! The lifters on 1,4,and 6 were sticking in the guide trays. Runs good now. I bought new felpro head gaskets. And bought the metal felpro intake gaskets. Runs good but after driving around for a hour or so I got a p219a code. I did smoke test on the intake. No leaks. I pulled fuel rail and checked fuel injectors. They are working great. Bought new o-rings and installed the injectors back in. Still getting p219a code. Help!

Supreme Pizza Senior Enthusiast

Supreme Pizza

Posted
Posted

I wonder if your 02 sensors on that bank are bad. I did a similar repair on a 5.3, because the intake lifter on #7 was collapsed. The engine was creating excessive vacuum in #7 cylinder, on the intake stroke. This was causing the engine to draw oil into that cylinder, and then push it into the exhaust system. I'm wondering if you had one or more cylinders doing the same thing. The oil may contaminate the O2 sensors, and then the computer would not be able to fine tune the fuel ratios properly. On your lifters that were sticking, was the problem caused by improperly aligned lifter guides?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • C/K Man
      Silverado 4500-5500-6500 are they still being produced? Would have sold better as GMCs as well

      By C/K Man · Posted

      There was talk over the last couple of years that the contract to build these trucks between GM and International would not be renewed.  International moved production of all their other trucks besides the companion CV model out of the Springfield plant some time ago when they opened their San Antonio plant.  That left Springfield only building the Silverado Medium Duty, International CV Series, and some Express/Savanna long wheelbase cutaways.  International also put the plant up for sale some time ago.  This all answered my earlier question as to why GM and International did nothing with these trucks since they were introduced, as they had basically become a market 'placeholder' with a finite life.    The Silverado Medium Duty/International CV trucks were interesting combination of a GM powertrain, electrical system, and K2XX Silverado cab with an International chassis that was supposedly designed for a step-van type vehicle they never produced.  They were manufactured in International's Springfield plant along with the IH MV series initially.  When first introduced, there was much talk that the Silverado Medium Duty/CV would eventually get a gasoline engine option along with other upgrades and GM and IH would work on a class 6/7 joint venture truck.  This was before VW bought Navistar out, after that happened no more was said.  Draw your own conclusions...   About the time talk started that the GM/IH joint venture was not going to be renewed, rumors started that GM would develop a new line of medium duty trucks themselves.  The story is the new trucks will be part of the next generation HD's due in 2028, and will still feature a 'straight rail' chassis design that the current medium duty has.  GM views this as a desirable feature that differentiates their truck from the competition.  A gasoline engine option is also expected.  As the current Silverado Medium Duty remains in production until September 2026 and there is still a lot of inventory available do not expect any official word for some time.   I believe GM remains committed to their successful partnership with Isuzu, and all the LCF models will still be available from Chevy Commercial dealers.  Isuzu is on the cusp of opening a new large plant in South Carolina and there is also speculation that this may result in new product for both Isuzu and Chevy Commercial dealers.                  
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • davester
      push to talk button

      By davester · Posted

      drive the truck back to the dealer and complain that the button works.
    • nfisherman
      Software Update

      By nfisherman · Posted

      I have a 2026 2500 HD Ultimate. My phone app says there’s a software update available. It’s something about improved battery management and something to do with the running boards. I follow the instructions for the update but the “Check for Updates” option is greyed out in my settings menu. Has anyone else seen this? How did you resolve it? The help message just says “see your dealer” if the download doesn’t work. I’m just trying to save a trip. 
    • newdude
      Exhaust Question

      By newdude · Posted

      Fuel mileage?  That's all how you use your right foot.  Exhaust will give you sound.   Stock exhaust 5.3 is 2.75" diameter piping.     If the truck is nice and worth putting some $$ into it, I'd go for a Corsa catback.  I had one on my 2019 old body 5.3 and it was just perfect.  Zero drone, just driving around and cruising on the highway you'd think it was stock, but when you opened it up it was like a Camaro with the factory dual mode.  Corsa bumps their catback to 3in diameter.  

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...