Jump to content

Recommended Posts

Posted

I noticed on our '21 Silverado with the L84 5.3 that there is a hose clip (see photo) that appears to be for one of the A/C hoses, but it's unclipped. Where should this be attached?

 

 

IMG-0911.jpg

Posted

i would attach it to that line with the heat wrap on it. To the right of the radiator house that the clip is attached too. 

 

Posted
2 hours ago, Kyle Ross said:

i would attach it to that line with the heat wrap on it. To the right of the radiator house that the clip is attached too. 

 

It looks like it is intended to go onto the A/C hose in the black mesh wrap to the left of it, but I wanted to double check before messing with it. The truck had a few lifters replaced on the passenger side a while back and it appears the dealer missed that clip on reassembly...

Posted
9 hours ago, voided3 said:

I noticed on our '21 Silverado with the L84 5.3 that there is a hose clip (see photo) that appears to be for one of the A/C hoses, but it's unclipped. Where should this be attached?

 

 

IMG-0911.jpg

On my 2020 5.3 the hose immediately to the left of the hose clip is what fits in the clip.

Posted
2 hours ago, Anacortes Army Guy said:

On my 2020 5.3 the hose immediately to the left of the hose clip is what fits in the clip.

Does the clip attach to the hose above or the hose below the T connector? I'm guessing above based on the alignment but wanted ask. If it's not too much of a bother, a picture would be great, but no pressure.

Posted

I'm going to be doing an oil change in a few hours I'll post my 2021 5.3 so you can see

Posted
23 minutes ago, Adamace1 said:

I'm going to be doing an oil change in a few hours I'll post my 2021 5.3 so you can see

Thank you! That would be great as I want to make sure it's in the correct spot. I mistakenly said earlier it was an A/C line but it's actually a heater hose so I don't want to risk damaging it and having coolant all over the place.

Posted
13 hours ago, voided3 said:

Does the clip attach to the hose above or the hose below the T connector? I'm guessing above based on the alignment but wanted ask. If it's not too much of a bother, a picture would be great, but no pressure.

 

Here's a picture.

Hose Clip.jpg

  • Thanks 1
Posted
9 minutes ago, Anacortes Army Guy said:

 

Here's a picture.

Hose Clip.jpg

Lol our are clipped on differently. IDK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Latest Articles

  • Posts

    • Length/amount of data capture will be important to consider, sifting through 5 minutes of a data log can be enormous when it is stored in milliseconds. Being able to find the 'event' let alone decipher it.   Presumably the driver would notice something and hit a button to capture the 'window' of data. That window has to be large enough for the operator to recognize the event and react accordingly.    The data has to be able to be retrieved easily.   The data has to be able to be understood. Which is the biggest challenge, dealer techs won't even know what most of it is and would likely not even look at it if an owner brought it to them. Meaning the owner, the least educated/qualified, trying to understand it.    How will the data be presented? Could specific PIDs be selected and a timelapse graph be watched? How will a specific value be noted as abnormal? Additionally, a good data logger would be able to 'learn' normal values for a specific vehicle and flag abnormalities automatically. It could in theory watch parameters degrade over time and suggest maintenance as needed. (If the MAF reading begins tapering off for a given set of other readings - MAP, throttle position, Ambient, etc.. a flag to check air filter.) With the amount of data available, a device (really the vehicle rather than an additional accessory) should be able to do more than issue a DTC. It should be able to run the full diagnostic suite automatically and present a solution rather than a code. (It's not the 90's anymore). The technology is available for the vehicle to not just say "P0087", it should know low fuel pressure, check other PIDs to narrow down the problem itself, and determine if it is a lift pump, high pressure pump, regulator, leak in the fuel line, clogged filter, etc. Even if it can't narrow it down, it should be able to guide the user to the likely problems.   This would be a major problem for dealer service departments, which are the manufacturers customers it is in their collective best interest to NOT have this available to the consumer.   Further, if the owner is going to be the primary consumer of the data, it's got to be at a consumer price point vs. dealer only specialty tool price.   This group is more 'involved' in their vehicle than general public/consumer and will have knowledge, experience, needs and desires that are quite different from the market at large.   
    • I put the prof up. If you read what I posted. You can see that housing, cars and income are in line with the era we were talking about. It’s harder in some places easier in others. Let’s agree to disagree and put this back on track, OK? We both are pretty stubborn and hard headed. But I bring receipts. If you wish I will not respond to you in the future. 
    • Lets see if I can sum up two pages of nothing useful.    You want to refute your own governments data of the "Purchasing Power" Index FOR THE ENTIRE USA and its territories replacing it with the experience of a single family and its business and label that reality?  Then pound on that for a week hoping it will find traction?    Stan, I've told you several times. I don't do irrational. There are more people in the USA than your family.    I'm pretty sure this tread is so blown up. I'll give you a few days or months if need be to post yourself silent then I'll see if I can find enough parts of the train to reassemble it. 
    • Facebook groups hate VSE, poor customer service; their responses to criticisms are pretty poor for a reputable company. I'm not a customer, haven't bought anything from them, but how they handle themselves on social media is a definite "No" for me. 
    • $10,000 for a transmission?   Pretty sure I could buy all the parts, tools, and education to rebuild it myself for a quarter of that amount.   or swap it out with a new one...
  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...