Jump to content

Door Panel & Dash Speaker Removal

mjonesjr84
 Share

Recommended Posts

mjonesjr84 Enthusiast

mjonesjr84

Posted
Posted

Does anyone have the instructions to remove the door speakers and dash speakers from a 2022 refresh Silverado? 

  • Like 1
ddc1279 Enthusiast

ddc1279

Posted
Posted

for the door panels, it is essentially the same as taking off the 21 door panels (front and rear).  On the front there are screws (7mm?) under a flap in the interior door handle and at the bottom of the door panel.  Then pop the door panel and lift up.  Same for rear but less screws.

 

for the dash..

 

 

  • Like 2
ddc1279 Enthusiast

ddc1279

Posted
Posted

I swapped my front speakers out for Audiofrog 6x9" (GS690) and the rear speakers with Audiofrog 6" (GS62).  I purchased from Crutchfield and the speaker adapter mounts and wire harness adapters for a 21 Silverado work the same.  I have no swapped out the dash speakers yet, but do plan to.  I just haven't gotten around to the having the time to deal with the dash and a-pillar removal.  When I do, I will be putting Audiofrog GS25's in.  So far, the front and rear door speaker swap has been good.  I think I need to go back and put some sound dampening because I can generate a little rattle.  Otherwise, the sound is great and it was a very easy install.

 

I have noticed that the speakers I put in my truck do not show as fitting the 22 refresh on Crutchfield, I can assure you that is incorrect.  The mount adapters and wiring harness are exactly the same.

  • Like 1
mjonesjr84 Enthusiast

mjonesjr84

Posted
  • Author
Posted
36 minutes ago, ddc1279 said:

I swapped my front speakers out for Audiofrog 6x9" (GS690) and the rear speakers with Audiofrog 6" (GS62).  I purchased from Crutchfield and the speaker adapter mounts and wire harness adapters for a 21 Silverado work the same.  I have no swapped out the dash speakers yet, but do plan to.  I just haven't gotten around to the having the time to deal with the dash and a-pillar removal.  When I do, I will be putting Audiofrog GS25's in.  So far, the front and rear door speaker swap has been good.  I think I need to go back and put some sound dampening because I can generate a little rattle.  Otherwise, the sound is great and it was a very easy install.

 

I have noticed that the speakers I put in my truck do not show as fitting the 22 refresh on Crutchfield, I can assure you that is incorrect.  The mount adapters and wiring harness are exactly the same.

I ordered Kicker 6x9's for the front and 6.5's for the rear. I got Pioneer 2-3/4's for the dash. 

 

The reason I asked was because I ordered them for a 2021 since Crutchfield says they don't have wiring adapters for the 2022 refresh.

 

I may go back in the future and add a 4 channel amp for the speakers.

  • Like 1
Will Jenkins Enthusiast

Will Jenkins

Posted
Posted
On 9/13/2022 at 1:21 PM, ddc1279 said:

I swapped my front speakers out for Audiofrog 6x9" (GS690) and the rear speakers with Audiofrog 6" (GS62).  I purchased from Crutchfield and the speaker adapter mounts and wire harness adapters for a 21 Silverado work the same.  I have no swapped out the dash speakers yet, but do plan to.  I just haven't gotten around to the having the time to deal with the dash and a-pillar removal.  When I do, I will be putting Audiofrog GS25's in.  So far, the front and rear door speaker swap has been good.  I think I need to go back and put some sound dampening because I can generate a little rattle.  Otherwise, the sound is great and it was a very easy install.

 

I have noticed that the speakers I put in my truck do not show as fitting the 22 refresh on Crutchfield, I can assure you that is incorrect.  The mount adapters and wiring harness are exactly the same.

Was it plug and play? Just had to get to the speaker to remove, attach adapters and plug in new speakers?

  • Like 1
mjonesjr84 Enthusiast

mjonesjr84

Posted
  • Author
Posted
4 hours ago, Will Jenkins said:

Was it plug and play? Just had to get to the speaker to remove, attach adapters and plug in new speakers?

Yes for the door speakers it is that easy.

  • Like 1
  • 3 weeks later...
RedLT Enthusiast

RedLT

Posted
Posted
On 9/13/2022 at 12:59 PM, mjonesjr84 said:

I ordered Kicker 6x9's for the front and 6.5's for the rear. I got Pioneer 2-3/4's for the dash. 

 

The reason I asked was because I ordered them for a 2021 since Crutchfield says they don't have wiring adapters for the 2022 refresh.

 

I may go back in the future and add a 4 channel amp for the speakers.

 

Did the speaker replacement make a noticeable difference to justify the labor and expense?  I mean does it put a smile on you when you listen to it or when you crank it up or is it more of a meh..  Referencing for a future amp leads me to believe it's leaning toward meh...

 

  • Like 1
mjonesjr84 Enthusiast

mjonesjr84

Posted
  • Author
Posted
3 minutes ago, RedLT said:

 

Did the speaker replacement make a noticeable difference to justify the labor and expense?  I mean does it put a smile on you when you listen to it or when you crank it up or is it more of a meh..  Referencing for a future amp leads me to believe it's leaning toward meh...

 

 

The sound was better, but will be even better with an amp to drive them.

  • Like 1
  • 2 months later...
Baymax0317 Enthusiast

Baymax0317

Posted
Posted
On 9/13/2022 at 10:59 AM, mjonesjr84 said:

I ordered Kicker 6x9's for the front and 6.5's for the rear. I got Pioneer 2-3/4's for the dash. 

 

The reason I asked was because I ordered them for a 2021 since Crutchfield says they don't have wiring adapters for the 2022 refresh.

 

I may go back in the future and add a 4 channel amp for the speakers.

What wiring harness did you use? Looking to upgrade my dash speakers too. I just got a Rockford Fosgate P300-10 and noticed dash speakers usually make the most difference. I have a 22’ Sierra refresh. 

mjonesjr84 Enthusiast

mjonesjr84

Posted
  • Author
Posted
13 hours ago, Baymax0317 said:

What wiring harness did you use? Looking to upgrade my dash speakers too. I just got a Rockford Fosgate P300-10 and noticed dash speakers usually make the most difference. I have a 22’ Sierra refresh. 

I ordered the door wiring adapters for a 2021 Silverado from Crutchfield when I got my speakers. They do fit the 2022+ trucks. The dash doesn't have a wiring adapter. You'll have to cut the plug off the factory wiring and put the terminal ends on that come with the speakers. There is plenty of wire to leave enough of the factory plug if you want to put the factory speakers back in.

Baymax0317 Enthusiast

Baymax0317

Posted
Posted

Thank you! Good information to have. I’m not sure yet to fill be doing it just got my sub and amp going to see how that enhances the sound before proceeding!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Latest Articles

  • Posts

    • Gkistler
      2015 Sierra Denali L86 cyl 5 misfire at idle

      By Gkistler · Posted

      Hi friends - first time poster. I have a 2015 sierra Denali with 150k miles, I’m the second owner and she’s given me 75k of great service. I run a pulse AFM disable device. Starting Thursday when I exited the freeway after a short local ride it started idling rough, with an obvious misfire shake and was down on low end power.  I got it home and hooked it up to my scannner and found no codes but in live data a pretty bad misfire on cylinder 5. I replaced the coil, plug and wire with all new OE replacements (Delphi gn10165 coil, acdelco wire and 41-168 plug). It’s still behaving the same way after firing the parts cannon at it.   I know cyl 5 is a non AFM cylinder so I am not thinking this is AFM related but I’m kinda at a loss. injector? Bent pushrod? It’s running too well over 1k rpm to suggest those IMO. Has anyone chase this issue before and what was it? Any suggestions? 
    • zibzer2
      Pulsating Noise 4Cyl Mode

      By zibzer2 · Posted

      2017 Silverado L83 5.3l 6speed transmission Hello, not a new member but havent posted in a while and my old signup info isnt working so had to create a new account. anyways, I have an issue with my truck and hope someone can spread some light on whats happening: -when it goes to 4cyl mode it makes a clunk sound (but not when coasting or going downhill) -when in 4 cyl mode and under load it makes a load pulsating sound (not a tick). -goes away completely when in M5 gear or when plugging in an AFM delete. Im guessing it is one of 2 things but im not convinced of either to be honest. 1. lifter stuck in v8 mode 2. torque converter shudder realistically it doesn't seem like the TC as there is no physical vibration , and it never happens in v8 mode. but maybe? and wouldnt a lifter make a sound whether with load or not? any ideas let me know please. thank you!  
    • Chuck FB
      Some Assembly is Required

      By Chuck FB · Posted

      Which has made me wonder with the various engine failures of a few brands in the last few years, is it sub par materials such as lifters etc causing failures, or bearing clearances on the crank etc or perhaps bad designing of an engine physically or causing too much load on the components due to the hp/torque they can push out of them. Or is the oil viscosity and additive package of current oils or a lack of oil flow by an oil pump not able to supply sufficient oil at idle or under high load at low rpm. Or is it every item I listed that combined together has pushed the limits so far to the left that there is hardly a margin of safety left and add in some fuel dilution and too long of an OCI and premature engine failure is the result ?. 
    • Grumpy Bear
      Some Assembly is Required

      By Grumpy Bear · Posted

      He is not saying that an SAE *W20 will have more viscosity than a *W40 due to MORE VII polymers. He is saying that although multiple *W40 may post in the PDS the same or similar 100 C and 150 C viscosities that the blenders choice of modifier TYPE and AMOUNT to get his chosen base to grade will not give identical real world viscosities in shear and at temperature. All will pass the SII test but not all will pass the 100 C HTHS (unpublished value) testing the blender does and relies on to get the required by law "percentage improvement' referenced to his last great work.    Tis the problem with the lie. Once told others are required to support it. 
    • PunchT37
      Parking Brake - Automatic Engagement Questions

      By PunchT37 · Posted

      I have a `25, 1500 that auto sets on incline. Never knew that at first. I have the electronic shifter. Just think if it didn`t do that? Unlike a mechanical shift that you can muscle out of park, how would you get this thing out? That would be a problem.   What I found out later is, I don`t have to push the button to release. Just put it in gear.   Setting parameters? Don`t know if it`s possible.

  • GM-Trucks.com Clubs

  • Popular Contributors

×
×
  • Create New...